LORUS W100 Instruction Manual

NREW100
I M
NSTRUCTION
CAL. W100 (RBM SERIES)
C H A R A C T E R I S T I C S
1 . T i m e / c a l e n d a r d i s p l a y : Hour, minutes,
seconds, month, date and day of the week.
• Fully automatic calendar: Calendar adjusts
automatically for odd and even months including
February of leap years from the year 1998 to
the end of 2048.
• T i m e i n d i c a t i o n : Changeover between
12- and 24-hour indications is possible.
2 . Stopwatch: Measures up to10 hours with 1/
100 second readout.
• Lap time measurement: When the fastest
lap time is measured, a beep sounds and the
display is illuminated.
• Auto start function: The stopwatch can be
set to start automatically at a desired time .
3. Countdown timer:
• Preset timer: Five different lengths of time
(3, 10, 15, 30 and 45 minutes) have been
preset for the timer.
• Adjustable timer: Up to 23 hours and 59
minutes can be set in minute increments.
4 . Daily alarm: The alarm can be set to ring on
a 24-hour basis.
• H o u r l y t i m e s i g n a l : Can be set to ring
every hour on the hour.
5 . Dual time: Time of a different time zone can
be set and displayed.
6 . I l l u m i n a t i n g l i g h t : The light illuminates
the display in the dark.
B U T T O N S A N D D I S P L A Y S
Hour Minutes
Seconds
AM/PM
m ar k
L i g h t
button
Day
A
A l a r m
m ar k
The selection of the display can be made in the
following order with each press of button "A".
A
T i m e r
T i m e / c a l e n d a r
d i s p l a y
d i s p l a y
A
A
A l a r m
S t o p w a t c h
d i s p l a y
d i s p l a y
With each press of button "B" in the time/calen-
dar display, the display changes over between
the time/calendar and dual time alternately.
B
T i m e / c a l e n d a r
NREW100 01-99
d i s p l a y
I M
NSTRUCTION ANUAL
CAL. W100 (RBM SERIES)

HOW TO SET THE TIME/CALENDAR

Hour Minutes Seconds
AM/PM
m ar k
A
Day Month
01-99
ANUAL
B
Month
D a t e
C
Hourly time
signal mark
A
D u a l t i m e
d i s p l a y
B
C
D a t e
1 . Press button "A" to show the time/calendar
d i s p l a y .
2 . Press button "A" for 2 seconds to show the
time/calendar setting display. The second
digits start flashing.
3 . Selection of the digits to be adjusted (flashing)
is made in the following order by pressing
button "B".
Seconds
Minutes
→ Hour
→
1 2 - / 2 4 - h o u r
D a t e
indication
4 . Press button "C" to set the flashing digits.
One digit is advanced with each press of
button "C". Digits except seconds and 12-
/24-hour indication move quickly by keeping
button "C" pressed.
5 . A f t e r a l l t h e a d j u s t m e n t s a r e c o m p l e t e d ,
p r e s s b u t t o n " A " t o r e t u r n t o t h e t i m e /
calendar display.
S e c o n d s s e t t i n g
When the seconds digits are flashing, press
button "C" in accordance with a time signal.
The seconds are reset to "00" and start immediately.
W h e n t h e s e c o n d s c o u n t a n y n u m b e r f r o m
" 3 0 " t o " 5 9 " a n d b u t t o n " C " i s p r e s s e d , o n e
minute is added and the seconds are immediately
reset to "00".
N o t e s :
1 . W h e n s e t t i n g t h e h o u r d i g i t s i n t h e 1 2 -
hour indication, check that AM/PM is properly
set. In the 24-hour indication, there is no
indication.
2. Once the year, month and date have been
set, the day of the week is set automatically.
3 . If the watch is left untouched in the time/
c a l e n d a r s e t t i n g d i s p l a y w i t h t h e d i g i t s
flashing, it will automatically return to the
time/calendar display in 2 minutes.
H O W T O U S E T H E S T O P W A T C H
• The stopwatch can measure up to 10 hours
i n 1 /1 0 0 s e c o n d s .
* Even if the stopwatch display is changed to
another while the measurement is in prog-
ress, it continues counting properly. After
the stopwatch is used, however, be sure to
reset it as the battery energy is consumed
enormously to shorten the battery life.
S t o p w a t c h
display mark
A
Minutes Seconds 1/100 seconds
S t o p w a t c h O p e r a t i o n
Press button "A" to show the stopwatch display.
Accumulated elapsed time measurement
B B B
S t a r t S t o p R e s t a r t
Accumulate repeatedly by
pressing button "B".
L a p t i m e m e a s u r e m e n t
• "Lap time" refers to an elapsed time required
to cover a given section of the whole distance.
L a p 1 C L a p 2
S t a r t B
R e s e t S t o p
C
** Can repeat by pressing button "C".
Note: When a lap time measured is the fastest
among the lap times previously measured,
a beep rings and the display is illuminated.
Year
→
M o n t h
B
C
B
C
S t o p
R e s e t
C
**
B