Advertisement
Selecting a folder
When a USB containing MP3 files in several folders is being played,
1. Press [PRESET/FOLDER +/- ] on the remote control repeatedly. Index of the first played file in the folder is displayed.
2. Press d/M on the unit or remote control to play it. The first file of the folder will play.
,
y USB Folders/Files are recognized as below.
y File will be played from $ file No.1 to $ file No.14 one by one.
y The Index number of folder will be presented in order recorded and may be presented differently according to the
recording circumstances.
y *ROOT : The first screen you can see when a computer recognizes the USB is "ROOT" .
Troubleshooting
No Power
Bluetooth pairing does not work well.
y The power cord is not plugged in. Plug in the power
y Switch Bluetooth off and on again on your Bluetooth
cord.
device, then try pairing again.
y Check whether electricity failed. Check the condition
y Be sure your Bluetooth device is on.
by operating other electronic devices.
y Remove the obstacle in the path of the Bluetooth
No sound and sound distortion
device and the unit.
y The unit or your external device' s volume is set to
y Depending on the type of the Bluetooth device or
minimum. Check and adjust the volume of the unit.
surrounding environment, your device may not be
y When you use external device at high volume, the
paired with the unit.
sound quality may be deteriorated. Lower the volume
y When your Bluetooth device have been already
of device.
connected with other unit, disconnect the
y If you use the unit for purposes other than listening to
Bluetooth connection first.
music, the sound quality may be lowered or the unit
Cleaning the unit
may not work properly.
y To clean the player, use a soft, dry cloth.
The USB device does not start playback
If the surfaces are extremely dirty, use a soft cloth
y An unplayable USB device is inserted. Check the USB
lightly moistened with a mild detergent solution.
device.
Do not use strong solvents such as alcohol, benzine,
or thinner, as these might damage the surface of the
y Check whether you selected right function. Pressing
unit.
[FUNC.] button and check the selected function.
Radio stations cannot be tuned in properly.
y The antenna is positioned poorly. Adjust its position.
y The signal strength of the radio station is too weak.
Tune to the station manually.
y No stations have been preset or preset stations have
been cleared (when being tuned by scanning preset
channels). Refer to Presetting Radio Station.
The remote control does not work properly.
y The remote control is not pointed at the remote
sensor of the unit. Point the remote control at the
remote sensor of the unit.
y The remote control is too far from the unit. Operate
the remote control within about 23 ft (7 m).
y There is an obstacle in the path of the remote control
and the unit. Remove the obstacle.
y The battery in the remote control is exhausted.
Replace the battery with new one.
LHS225D-FB.AVNMLLK_ENG_MFL69306414.indd 2
Radio Operation
Listening to the radio
1. Press [FM/AUTO SCAN] on the remote control or [FUNC.] on the unit until FM appears in the display
FM antenna
window.
The last received station is tuned in.
2. - Auto tuning: Press [TUN.-/+] on the remote control or [TUNING -/+] on the unit for about 1 second
until the frequency indication starts changing, then release. scanning stops when the unit tunes in a
FM
ANTENNA
station.
- Manual tuning: Press [TUN.-/+] on the remote control or [TUNING -/+] on the unit repeatedly.
3. Adjust the volume by using [VOL +/-] on the remote control or the unit.
,
y Be sure to fully extend the FM wire antenna before using the radio function.
y Before tuning, make sure to turn down the volume.
y Press d/M on the remote control. This will change the tuner from stereo to mono.
Then the FM reception will be better than before.
Presetting Radio Station
Presetting the Radio Stations
1. Press [FUNC]on the remote control or [FUNC.] on the unit until FM appears in the display window.
2. Select the desired frequency by pressing [TUN.-/+] on the remote control or [TUNING -/+] on the unit.
3. Press [PROGRAM/MEMORY]. A preset number will blink in the display window.
4. Press [PROGRAM/MEMORY]. The station is saved.
5. Repeat steps 2 to 4 to store other stations. You can preset up to 50 stations for FM.
6. To listen a preset station, press [PRESET/FOLDER +/-].
Using AUTO SCAN
1. Press [FM/AUTO SCAN] on the remote control for longer than 2 seconds, all of the FM bands are scanned.
2. Radio frequencies are saved automatically by preset number while FM bands are scanned.
3. To cancel the scanning, press Z or convert to other function. It will be cancelled.
Deleting a saved Preset station
1. Select a desired Preset by pressing [PRESET/FOLDER -/+] and press [DELETE] on the remote control.
2. The selected Preset number will be blinked.
3. Press [DELETE] on the remote control to erase the saved preset number.
,
Press and hold [DELETE] to erase all saved radio stations.
Specification
Auto power down
This unit will turn itself off to save electricity in the case
were the main unit is not connected to an external device
and is not used for 20 minutes.
The unit will also turn itself off after six hours if the Main
unit has been connected to another device using the
analog inputs.
How to disconnect the wireless network
connection or the wireless device.
Turn off the unit.
Product type:
- 2.1 speaker system
Power Supply
- Refer to the main label.
Power Consumption
- 20 W
Dimensions (W x H x D):
- Satellite: Approx. 110 (W) mm x 201 (H) mm x 115
(D) mm
- Subwoofer: 264 (W) mm x 370 (H) mm x 323 (D)
mm
Net Weight:
- Main Set : Approx. 5.44 kg
Speaker (1EA) : Approx. 0.64 kg
Operating Temperature:
- 0 °C to 35 °C
Connectivity:
- 3.5mm stereo jack-male input jack
Tuner:
- FM Tuning Range : 87.5 to 108.0 MHz or 87.50 to
108.00 MHz
Impedance:
- Subwoofer: 6 (Ω)
- Satellite: 8 (Ω)
Frequency response
- Subwoofer: 55 Hz~ 104 Hz
- Satellite: 40 Hz ≤ 20 kHz
Total Max. power
- 70 W (THD : 10 %)
Signal to noise ratio
- 75 dB
y Design and specifications are subject to change
without notice.
Using BLUETOOTH®
Before you start the pairing procedure, make sure that the Bluetooth
feature is turned on in your Bluetooth device.
/
1. Press [1 POWER] to turn on the unit or remote control.
2. Select the (Bluetooth)
the unit or
button on the remote control.
3. "
" will blink to find a Bluetooth device on the display window.
Select "LG LH70B (XX)" on your Bluetooth device.
(XX) means the last two digits of BT address.)
y Depending on the Bluetooth device, you need to enter the PIN code (0000).
4. When this unit successfully paired with your Bluetooth device,
"
" will stop blinking.
5. Play music on your
Bluetooth
,
y Sound from the main set can be distorted if you raise the volume of Bluetooth device up to two-thirds or more.
y When you use the Bluetooth function, adjust the volume of a Bluetooth device to a proper level to listen to.
y When using Bluetooth® technology, you have to make a connection between the unit and the Bluetooth device as
close as possible and keep the distance. However it may not work well in the case below :
- There is a obstacle between the unit and the Bluetooth device.-
- There is a device using same frequency with Bluetooth® technology such as a medical equipment, a microwave
or a wireless LAN device.
y You should connect your Bluetooth device to this unit again when you restart it.
y Pairing is limited one Bluetooth device per one unit and multi-pairing is not supported.
y When you select Bluetooth function again after changing to other functions, the last connected Bluetooth device is
connected automatically.
y Depending on the type of the device, you may not be able to use the Bluetooth function.
y Bluetooth connection will be disconnected when the unit is turned off or the Bluetooth device gets too far from the
unit.
NOTICE: For safety marking information including product
CAUTION
identification and supply ratings, please refer to the main label on the
bottom or rear of the apparatus.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
This device is equipped with a portable battery or accumulator.
REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE
Safety way to remove the battery or the battery from the
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
equipment: Remove the old battery or battery pack, follow the
steps in reverse order than the assembly. To prevent contamination
of the environment and bring on possible threat to human and
This lightning flash with arrowhead symbol within
animal health, the old battery or the battery put it in the appropriate
an equilateral triangle is intended to alert the
container at designated collection points. Do not dispose of batteries
user to the presence of uninsulated dangerous
or battery together with other waste. It is recommended that you use
voltage within the product' s enclosure that may
local, free reimbursement systems batteries and accumulators. The
be of sufficient magnitude to constitute a risk of
battery shall not be exposed to excessive heat such as sunshine, fire
electric shock to persons.
or the like.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION: The apparatus shall not be exposed to water (dripping or
splashing) and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
WARNING: Do not install this equipment in a confined space such as
a book case or similar unit.
CAUTION: Do not use high voltage products around this product.
(ex. Electrical swatter) This product may malfunction due to electrical
shock.
CAUTION: Do not block any ventilation openings. Install in accordance
with the manufacturer' s instructions.
Slots and openings in the cabinet are provided for ventilation and
to ensure reliable operation of the product and to protect it from
over heating. The openings shall be never be blocked by placing the
product on a bed, sofa, rug or other similar surface. This product shall
not be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer' s instruction
has been adhered to.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit;
That is, a single outlet circuit which powers only that appliance and
has no additional outlets or branch circuits. Check the specification
page of this owner' s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged wall outlets,
extension cords, frayed power cords, or damaged or cracked wire
insulation are dangerous.
Any of these conditions could result in electric shock or fire.
Periodically examine the cord of your appliance, and if its appearance
indicates damage or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an exact replacement part
by an authorized service center. Protect the power cord from physical
or mechanical abuse, such as being twisted, kinked, pinched, closed in
a door, or walked upon. Pay particular attention to plugs, wall outlets,
and the point where the cord exits the appliance.
The Power Plug is the disconnecting device. In case of an emergency,
the Power Plug must remain readily accessible.
function by pressing [FUNC.] on the front of
device.
2017-03-20
9:06:05
Advertisement
