1 Precautio 1-1 Safety Precautions WARNINGS Inspect all protective devices such as nonmetallic For continued safety, do not attempt to modify the control knobs, insulating materials, cabinet backs, circuit board. adjustment and compartment covers or shields, isolation resistor-capacitor networks, mechanical Disconnect the AC power before servicing.
1 Precautions 1-2 Servicing Precautions WARNING1: First read the “Safety Precautions” section of this manual. If unforeseen circumstances create conflict between the servicing precautions and safety precautions, always follow the safety precautions. WARNING2: A high voltage VR replaced in the wrong direction may cause excessive X-ray emissions.
2 Product Specifications 2-2 Pin Assignments Sync Type Macintosh Separate Pin No. GND-R Green Blue H/V Sync. Sense 0 DDC Return Green GND-R GND-G GND-G Sense 1 GND-B Reserved Blue GND-Sync. /Self-raster Sense 2 DDC Data V-Sync. H-Sync. GND-B V-Sync. DDC Clock H-Sync.
2 Product Specifications 2-3 Timing Chart This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals. Table 2-1. Timing Chart Mode VESA VGA2/70 Hz VGA3/60 Hz 640/85 Hz 800/75 Hz 800/85 Hz 1280/75 Hz 1024/75 Hz...
3 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the TT17J* monitor. WARNING: This monitor contains electrostatically sensitive devices. Use with caution when handling these components. 3-1 Disassembly Cautions:1. Disconnect the monitor from the power source before disassembly. 2.
Page 9
3 Disassembly and Reassembly 3. Disconnect all connectors on the CRT Socket 6. Remove the screws on the back and along PCB. each side of the Bottom Chassis. 4. Using a solder iron, disconnect Ground (G2) 7. Carefully lift the Main PCB Ass’y and remove on the back of the Video Shield and remove the remaining ground wires.
4 Alignment and Adjustments This section of the service manual explains how to make permanent adjustments to the monitor. Directions are given for adjustments using the monitor Interface Board Ver. 2.0 and software (Softjig). 4-1 Adjustment Conditions Caution: Changes made without the Softjig are saved only to the user mode settings. As such, the settings are not permanently stored and may be inadvertently deleted by the user.
Page 11
4 Alignment and Adjustments 4-1-3 Connecting the SoftJig Connect the monitor to the signal generator and/ MONITOR or PC as illustrated in Figures 4-1 and 4-2. INTERFACE Note: The signal cable connector which includes BOARD VER. 2.0 3-WIRE CABLE the 3-wire cable must connect to the monitor.
Page 12
4 Alignment and Adjustments 4-2 Display Control Adjustments 4-2-1 HIGH VOLTAGE ADJUSTMENT Signal: 1024 x 768 (68 kHz/85 Hz) 4-2-4 Centering Display image: Don’t care Centering means to position the center point of Contrast: Minimum the display in the middle of the display area. Brightness: Minimum Horizontal size and position and vertical size and...
Page 13
4 Alignment and Adjustments 4-2-4 (c) HORIZONTAL POSITION ADJUSTMENT 4-2-5 (a) HORIZONTAL LINEARITY ADJUSTMENT CONDITIONS CONDITIONS Scanning frequency: 68 kHz/85 Hz Scanning frequency: 68 kHz/85 Hz Display image: Crosshatch pattern Display image: Crosshatch pattern Brightness: Maximum Use control bar after selecting “H-POSITION” in Contrast: Maximum left menu to center the horizontal image on the...
Page 14
4 Alignment and Adjustments 4-2-7 Pinbalance Adjustment 4-2-9 Side Pincushion Adjustment CONDITIONS CONDITIONS Scanning frequency: 68 kHz/85 Hz Scanning frequency: 68 kHz/85 Hz Display image: Crosshatch pattern Display image: Crosshatch pattern Brightness: Maximum Contrast: Maximum Use control bar after selecting “PINCUSHION” in left menu to straighten the sides of the image area.
Page 15
4 Alignment and Adjustments 4-3 Color Adjustments CAUTION:Check below condition before color 4-3-2 (b) WHITE BALANCE ADJUSTMENT adjustment CONDITIONS Video signal : Analog 0.7 Vp-p (at 75 Ω) Scanning frequency: 68 kHz/85 Hz Sync : TTL level (H, V seperate signal) Display image: White box pattern Brightness:...
Page 16
4 Alignment and Adjustments 4-3-2 (d) WHITE BALANCE ADJUSTMENT VERIFICATION 4-3-3 Luminance Uniformity Check Luminance is considered uniform only if the ratio CONDITIONS of lowest to highest brightness areas on the screen Scanning frequency: 68 kHz/85 Hz is not less than 7.5:10. Display image: Back raster pattern Full White Pattern...
Page 17
4 Alignment and Adjustments 4-3-5 Color Purity Adjustment Color purity is the absence of undesired color. Conspicuous mislanding (unexpected color in a uniform field) within the display area shall not be visible at a distance of 50 cm from the CRT surface.
5 Troubleshooting 5-1 Parts Level Troubleshooting Notes: 1. If a picture does not appear, fully rotate the brightness and contrast controls clockwise and reinspect. 2. Check the following circuits. • No raster appears: Power circuit, Horizontal output circuit. • High voltage develops but no raster appears: Video output circuits. •...
Page 19
5 Troubleshooting 5-1-2 DPMS Failure WAVEFORMS Check signal source H/V sync. video level. 100V (IC601, #1) Make No H/V sync. (power off mode) CH1 P-P = 100V CH1 RMS = 325.8 V LED blinks? Check IC201 Pin 40. +12 V line off? Check IC201 Pin 6.
Page 20
5 Troubleshooting 5-1-3 H_Deflection Failure Does PWM output signal appear Does DC 12V appear at Check 12 V line. at Pin 6 (H_out) of IC401? Pin 10 of IC401? WAVEFORMS Check IC401. 2.00 V (IC401, #6) Does Horizontal paluse signal Check IC401.
Page 21
5 Troubleshooting 5-1-5 H_Lin. Failure IC201 Pin 21 voltage varies with Replace IC201. different H_Lin. DAC values? IC603 Pin 9 voltage varies with Check +13 V, –10 V line. different H_Lin. DAC values? Check some parts around IC603. Check Q412, Q413 and T402. 5-1-6 Invariable H_Size IC401 Pin 6 voltage varies with Check and replace IC401.
Page 22
5 Troubleshooting 5-1-8 Side Pin or Trap Failure WAVEFORMS IC401 Pin 11 output exists? Check and replace IC401. 1.00 V (IC401, #11) Refer to 5-1-7 Abnormal H_Size . CH1 P-P = 1.00V CH1 RMS = 3.008 V 5-1-9 Para. or Pin Balance Failure IC401 Pin 11 output varies with Refer to 5-1-7 Abnormal H_Size .
Page 23
5 Troubleshooting 5-1-11 V Deflection Failure WAVEFORMS 13 V, –10 V line is on? Refer to 5-1-1 No Power Supply 5 V (IC401, #12) IC401 Pin 12 output exists? Check and replace IC401. CH1 P-P = 5 V CH1 RMS = 1.425 V 10.0 V (IC301, #6) Check and replace some parts IC301 Pin 6 output exists?
Page 24
5 Troubleshooting 5-1-13 High Voltage Failure WAVEFORMS Check and replace IC401 IC401 Pin 6 OSC pulse exists? 2.00 V (IC401, #6) and +12 V line. Q402 Gate driving pulse exists? Check and replace Q401 and Q423. CH1 P-P = 2.00 V CH1 RMS = 5.868 V 2.00 V (Q402, Gate) Check and replace D401, Q403...
Page 25
5 Troubleshooting 5-1-15 Dynamic Focus Failure WAVEFORMS IC401 Pin 32 output is right? Replace the IC401. 2.00 V (IC401, #32) Some parts around Q551 are right? Replace failed part. CH1 P-P = 2.00V CH1 RMS = 6.124V 50.0 V (T502, #6) T502 Pin 6 input is right? Check and replace C432.
Page 26
5 Troubleshooting 5-1-16-B No Video (PC Mode) WAVEFORMS Check signal cable and connection. 1.00 V (IC101,#12,14,16) IC701 Pin 1, 3 and 5 inputs Check the signal cable connection. are right? CH1 P-P = 1.00V CH1 RMS = 2.452V 1.00 V (IC101, #18,21,24) IC101 Pin 12, 14 and 16 inputs Check the connector Ass’y.
Page 27
5 Troubleshooting 5-1-17 Micom Failure WAVEFORMS IC201 Pin 11 input voltage is 5V? Check IC604. 1.00 V (IC201, #13, 14) IC201 Pin 13 and 14 inputs Check C202, C203 and X201. are right? CH1 P-P = 1.00 V CH1 RMS = 2.108V IC201 Pin 18 input is right? Check IC605.
Page 28
5 Troubleshooting 5-1-18 OSD Failure WAVEFORMS Check CN104 and connector Ass’y. 1.00 V (IC101, #32) Check and replace Q102. IC101 Pin 32 input is right? Check CN102 Pin 14. CH1 P-P = 1.00V CH1 RMS = 4.516V 1.00 V (IC101, #1) IC101 Pin 1 input is right? Check CN102 Pin 8.
Page 29
5 Troubleshooting 5-1-19 User Control Failure Does the DC level change at Check the button. Pin 36 of IC201 when you push the (SW201 ~ SW204) button S/W? Check IC201. 5-1-20 Degaussing Failure Check degaussing connector. RL601 operation is right? Check D-coil and TH601.
5 Troubleshooting 5-2 General Troubleshooting 5-2-1 No Picture LED blinks? Refer to 5-2-2 Shut down. LED is green color? Check Micom. Check G2 voltage, high voltage and R, G, B cathode voltage. 5-2-2 Shut Down Blinking LED’s? Check power supply. Check horizontal, vertical deflection Scan failure? system and check power supply...
Page 31
5 Troubleshooting 5-2-3 Missing Color WAVEFORMS Pproper Video levels are 10.0 V (R,G,B, Video) Check signal generator. on CN101 (D-Sub) Pin 1, 3 and 5? Proper Video signal Refer to 5-1-16 No Video. is on all cathodes? CH1 P-P = 10.0V CH1 RMS = 17.02V Check IC101 Pin 17, 20 and 23.
Page 32
5 Troubleshooting 5-2-4 Visible Retrace WAVEFORMS Check white balance adjustment. 5.00 V (Q303, Collector) G2 voltage is right? Check D502, Q501 and Adjust G2. CH1 P-P = 5.00V CH1 RMS = 28.33V 20.00 V (CRT SOCKET, G1) Blank pulse is on Pin 17 of IC401? Check IC401.
Page 33
5 Troubleshooting 5-2-5 Unsynchronized Image Check input signals Pin 2 and 3 of CN202. Signals are right? Check Video Cable Signals at Pin 28 and 29 of Check IC201. IC201 are right? Signals at Pin 14 and 15 of Check IC401 IC401 are right? Check circuits on Main board.
Page 34
5 Troubleshooting 5-2-6 Misconvergence Try readjusting convergence. The convergence is now Done within spec.? Readjust convergence. The convergence is now Done within spec.? Change CRT and readjust convergence. Done TT17J* 5-17...
Page 35
5 Troubleshooting 5-2-7 Poor Focus Adjust focus VR of FBT. Aging monitor and check for focus Improved focus? change. Check focus leads from FBT to CRT Socket. Check the CRT Socket. Refer to 5-1-15 Dynamic Dynamic focus circuit is right? Focus Failure.
Page 57
7 Electrical Parts List 7-3 Others Part Name Code No. Description Specification Remarks BH03-00024D CRT-SF M41QCJ761X172(P/5),96,17,0.25,-,29.1,FST,H/C,NH,-,FILM,TILT,4 DEGAUSSING BH27-00062A COIL DEGAUSSING-ASS’Y 320*250*1100mm,TS17J,TS17JS,9.6mH,¡≤20%,100Ts,9.0§Ù,-,17,90-265VAC,-,15.2¥Ø,320 ASS`Y PBA UNIT BH94-00233A ASSY PCB-SF TT17JS-08E1/0804,-,-,- B/D ASS`Y CODE BH98-00213A ASSY PCB/MAIN-SF TT17JS-08E1/0804,-,-,- BH98-00214A ASSY PCB/VIDEO-SF TT17JS-08E1/0804,-,-,- S/CABLE BH39-00309A CBF SIGNAL TT17JS,15P/09P,05P,2990,1500MM,UL2990,HALF BLUE,D-SUB/MALE,-,-,-...
Page 58
VIDEO BOARD Signal VIDEO PRE-AMP VIDEO OUTPUT + OSD IC705 IC103(LM2413) IC101(KB2502) IC704 IC703 Line SOCKET Composite Video RGB - CUTOFF Video Decoder Doubler QR, G,B01,02 Baseband Signal HEATER MAIN BOARD Sync H-SYNC, V-SYNC KA2142 TDA4859 H/V SIZE REG. H-SYNC1 VER.