Table of Contents
Advertisement
When the user input or
RST
corresponding "on" output is reset immediately and remains off until the
trigger point is crossed again. (Previously latched alarms will be off if power
up Display Value is lower than setpoint value.)
= Latch with delay reset action; This action latches the output on at the
L-dLY
trigger point per the Setpoint Action shown in Setpoint Output Figures. Latch
means that the output can only be turned off by the front panel
or user input manual reset, serial reset command or meter power cycle. When
the user input or
button is activated (momentary action), the meter
RST
delays the event until the corresponding "on" output crosses the trigger off
point. (Previously latched outputs are off if power up Display Value is lower
than setpoint value. During a power cycle, the meter erases a previous
reset if it is not activated at power up.)
SP
SP - Hys
{
OFF
ON
OUTPUT
OFF
ON
STATE
OFF
ON
Setpoint Output Reset Actions
OUTPUT RESET WITH DISPLAY RESET
rEn-n
NO
YES
This parameter enables the
RST
the display is reset.
Note: For this parameter to operate, the
must be set to
and the Input value must be displayed. If these conditions are
dSP
not met, the output will not reset.
5.5 Module 5 - S
5-SEr
SEL
bAUd
Baud Rate
The Serial Setup Parameters are only active when one of the optional serial communications/programming cards is installed in the meter.
Refer to the CUB5COM bulletin for details and setup for the CUB5 RS232 or RS485 serial communications.
Refer to the CUB5USB bulletin for details on the CUB5 USB programming and programming requirements.
The Company warrants the products it manufactures against defects in materials and workmanship for a period limited to two years
from the date of shipment, provided the products have been stored, handled, installed, and used under proper conditions. The
Company's liability under this limited warranty shall extend only to the repair or replacement of a defective product, at The
Company's option. The Company disclaims all liability for any affirmation, promise or representation with respect to the products.
The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify RLC against damages, claims, and expenses
arising out of subsequent sales of RLC products or products containing components manufactured by RLC and based upon personal
injuries, deaths, property damage, lost profits, and other matters which Buyer, its employees, or sub-contractors are or may be to
any extent liable, including without limitation penalties imposed by the Consumer Product Safety Act (P.L. 92-573) and liability
imposed upon any person pursuant to the Magnuson-Moss Warranty Act (P.L. 93-637), as now in effect or as amended hereafter.
No warranties expressed or implied are created with respect to The Company's products except those expressly contained herein.
The Customer acknowledges the disclaimers and limitations contained herein and relies on no other warranties or affirmations.
button is activated (momentary action), the
RST
MANUAL
RESET
(
)
OFF
OFF
ON
Auto
(
)
OFF
OFF
LAtCH
ON
OFF
OFF
(
)
L-dLY
ON
YES
button or user input to reset the output when
button or User Input being used
RST
erial
PARAMETER MENU
PAr
dAtA
Data Bit
Parity Bit
Stb-n
NO
When
, the output is disabled (after a power up) until the trigger point is
YES
crossed. Once the output is on, the output operates normally per the Setpoint
button
Action and OutputReset Action.
L-dLY
brn-n
OFF
Hys
Enter the probe burn-out action. In the event of a temperature probe failure
(open), the output can be programmed to be on or off.
CHANGE DISPLAY COLOR w/OUTPUT STATE
ChC-n
NO
This parameter enables the backlight CUB5 to switch the backlight color when
the output state changes. This parameter is only active for the backlight version.
S
p
etup
araMeterS
Addr
Meter
Address
LIMITED WARRANTY
11
STANDBY OPERATION
NO
YES
PROBE BURN-OUT ACTION
OFF
ON
NO
YES
(
)
5-SEr
Abbr
OPt
Abbreviated
Print
Printing
Options
Pro
Advertisement
Table of Contents
