Maxxima MEW-S150DW Instruction Manual

* Tools Required for Assembly (not included): screwdriver.
WORKS WITH PART DESCRIPTION
amazon alexa
A Switch
B Wall plate
MEW-S150DW
C Wire nuts
Indoor D Mounting screws (Wall box)
Wi-Fi In-Wall Switch
E Mounting screws (Wall plate)
F Jumper wire
INSTRUCTION GUIDE
Step1
This device is to be installed in a single gang box measuring at least
3" x 2" x 2.5" (standard single gang box) and wired in accordance with NEC.
Step2
Straighten each conductor and strip 1/2" of insulation from
each wire.
Step3
Begin by loosening all the screws on your ECO In-Wall switch. You'll notice there
is now a loose plate in the hole. The wires will need to be inserted in the middle
and tightened with a screwdriver. (See figure 3).
The screw terminals accept up to 12AWG copper wire.
3
125Vac, 60Hz, 15A Resistive,
15A General Use, 1000W Tungsten,
500VA Electronic Ballast,
120Vac, 60Hz, 8.3A Ballast, 1/2HP.

INSTALLING

Warning: To avoid fire and/or shock, turn off power. Make sure
! !
the power is off before wiring. If you are unsure or uncomfortable
with installation, contact a licensed electrician.
CAUTION! INDOOR USE ONLY! Do not use the Wi-Fi In-Wall
Switch outdoors or in damp or wet locations.
Step4
Wiring the Wi-Fi In-Wall switch.
Package Contents:
4
A B C
Ground
Neutral
Neutral
Ground wire (Green/Bare)
Neutral wire (White) Hot wire
Load wire (Black/Red)
Load
Hot wire (Black) wire
D E F Step4 Cont.
1. Insert the ground wire(s) into hole(s) labeled "G" (near green screw
2. Insert 2 neutral wires into the holes labeled "N" (near silver screw)
3. Insert the hot wire into the hole labeled "L-I" (near brass screw)
4. Insert the load wire into the hole labeled "L-O" (near brass screw)
Step5

SETUP INSTRUCTION

5-1
QUANTITY The ECO In-Wall switch requires a neutral wire
connection or the switch will not work.
1
5-1. If the existing neutral (white) wires are
1 READ ALL INSTRUCTIONS before using the Wi-Fi In-Wall Switch.
! !
connected by wire nut in the wall box,
1
RECOMMENDATION: The closer the Wi-Fi In-Wall Switch is
release the nut, insert both neutral wires
0.748 in. - 2
into the holes labeled N (near silver located to a WiFi router during set-up, the better the signal
0.33 in. - 2
strength will be for initial configuration and subsequent
screw). (See figure 5-1).
15 cm - 1
programming.
Mac address: If your router identifies by Mac address, please
key in the code number shown in the code label of the unit.
5-2. If the neutral wires from the wall box are i.e., 3x:2x:7x:0x:Cx:Cx
short and do not reach the N hole, cut the 5-2 Wall
CAUTION! INDOOR USE ONLY! RISK OF ELECTRIC SHOCK.
wire at 1-1/4 in. (include the period) from longer cord
Strip Length:
Use this product only in dry, indoor locations.
the bottom of case, remove jacket at 1/2 in.
1/2" (include the period) of both ends. Insert
Jumper
(1.27cm)
longer cord to N hole. Connect the shorter wire(F)
cord with enclosed jumper wire (F) and
wire nut, then insert to another N hole Wi-Fi Home Router
(near silver screw) (See figure 5-2).
1-1/4"
shorter cord
5-3. Tighten all screws firmly. (12lbf-in).
(See figure 5-3).
5-3
Power Indicator
SWITCH BUTTON:
Press to turn
ON/OFF
DEFAULT RESET
Step6

RESET THE Wi-Fi IN-WALL SWITCH

Carefully fold wire into the wall box and mount the Wi-Fi In-Wall switch (A) into
This is how you perform a factory reset of the Wi-Fi In-Wall switch
wall box using the mounting screws (D), then attach the wall place using the
Wall
mounting screws(F). (See figure 6).
blinking
6
B
A
D
E
1 2
STEP STEP
Press and hold the Hold the power button until
power button Insert the Wi-Fi In-Wall indicator
D
a non-conducting light TURNS OFF, then
E stick into the RESET release the button.
hole, then release it
Step7
Restore power by flipping the breaker to the "on" position or re-installing the fuse
to the circuit.

SMARTPHONE SETUP

*If this ECO-XXX network does not show in your list, perform a factory
RESET of the Wi-Fi In-Wall Switch
DOWNLOAD THE ECO PLUGS APP: ECO Plugs
*If your router does not show up in the list, press the
You can download the ECO Plugs App from either the Apple APP
manually enter your router's information
Store (iPhone) or the Google Play Store (Android)
Scan the QR Codes below or search for 'ECO Plugs'
EX: USA
USA
Enter Zip Code:
...
Name Device:
Wi-Fi Router(WLAN):
Home Router
Enter Wi-Fi Router Password:
(Wi-Fi's password, if needed)
(iOS 7 or higher) (Version 4 or higher)
*If you purchase more than one ECO In-Wall Switch , setup each device one
Wi-Fi ™ Status Indicator
by one .
Fill in Country,
LIGHT BLINKING LIGHT
Wi-Fi In-Wall Switch is
STEP 1 STEP 2
ready for programming
Name Device (Lamp, TV, small appliances) and Router Password, click the
Your phone
Your phone SAVE SETTING or JOIN button.
FAST BLINKING LIGHT
Wi-Fi In-Wall Switch Tap the
* iOS: If you can't find the
cannot find a WiFi router. Wi-Fi/WLAN icon
Please reset.
*For Canada: Please select Canada, entering the phone area code instead
Wi-Fi/WLAN on
SOLID LIGHT: of zip code.
Programming is finished and the
Setting
Wi-Fi In-Wall Switch is now
*Your smartphone should reconnect to your home router. If it does
ready to be used
not, go back into your phone WiFi settings to connect back to it.
via ECO Plugs APP
Turn on
! Go into your phone's Wi-Fi setting
Well installed Switch
NO LIGHT:
(Normally is as gear icon symbol first.)
Wi-Fi In-Wall Switch is rebooting
to default settings
RESET
STEP 3 STEP 4
Congratulations!...
Your phone Your phone Your phone
Select the
ECO-XXXXXXXX
Wi-Fi
ECO-XXXXXXXX
abcde
Xyz95
ECO-XXXXXXXX Complete setup...
Xyz95
xrgtg4 xrgtg4
ECO Plugs
Home Home
blinking blinking
OFF
Tap the

ADD MULTI Wi-Fi IN-WALL SWITCH TO THE APP

Select the ECO Plugs # (ECO-XXXXXXXX)
!
ECO Plugs APP
which labelled on the product.
Repeat steps 1-8 for each additional device. Remember to give each device a
different name (for example, Light 1, Light 2, etc.).
STEP 5 STEP 6
3 *Note: each controlled device requires a separate Wi-Fi In-Wall Switch.
STEP
Select Wi-Fi Network USA Canada Other
Finished! You can
now start setting up Device [ECO-XXXXXXXX] Enter Zip Code:
the ECO Plugs APP
Home Router
Name Device: (Named This Device)
with the Wi-Fi In-Wall
Other Router A Wi-Fi Router(WLAN):
Other Router B
Home Router
Enter Wi-Fi Router Password:
Select the Wi-Fi home router that
(Wi-Fi's password, if needed)
you want to connect to the WI-Fi
In-Wall Switch or tap ( )
(EX: Home Router) Fill in all your information.

ADD MULTIPLE USERS TO ECO PLUGS

Repeat the steps below for each additional user
icon to Your phone
Your phone
Tap the
Wi-Fi/WLAN icon
STEP 7
Wi-Fi/WLAN on
EX: CANADA
Setting
Canada Other USA Canada Other
2142 (Cambridge) Phone Area Code: 416 (Toronto)
Tap iOS's
Name Device: ! setting gear icon
(Named This Device) (Named This Device)
Android's
Wi-Fi Router(WLAN):
(Not the ECO Plugs APP)
Home Router
Enter Wi-Fi Router Password:
(Wi-Fi's password, if needed)
Your phone
Your phone
Tap the
Join / Save Setting Wi-Fi ECO Plugs APP
Home Router
Zip Code (USA Only)
Xyz95
xrgtg4
Phone Area Code (CANADA Only)
Home
Link to the same router Wi-Fi
* For cloud function. Refer
Netork as used by the first
Join button, please click in the password section.
smartphone (EX: Home Router) to EXPLORE THE TIMER
SETTING
CONTROL MULTIPLE DEVICES
*ONLY IF YOU HAVE MORE THAN ONE Wi-Fi DEVICES PROGRAMMED
ON THE ECO PLUGS APP: You can choose which Wi-Fi Devices (EX: Light 1,
STEP 8
Light 2, Light 3, etc.) you want to control by sliding the desired icon to the lower
Your phone
Your phone left position.
ECO
The Wi-Fi Devices name (EX: Light 1, Light 2, etc.) will change color from white to
yellow. The chosen is now able to be programmed or edited; such as
device
Light 1 changing timer settings, setting security settings, updating the cloud service, etc.
*Note: YOU CAN CONNECT TO A MAXIMUM OF TWELVE (12) Wi-Fi
Successful !
DEVICES VIA THE ECO PLUGS APP.

EXPLORE THE ECO PLUGS APP ICONS

More - Learn more about ECO Plugs app, including a Q & A section.
Electric Bill - Function is not available on this device.
Select the timer function
Setting - Setting your Wi-Fi In-Wall Switch, such as transfer local Wi-Fi into Tap
from the list
cloud mode, or rename the device.
Timer - Setting On/ Off programs (up to a maximum of 12 Custom On/ Off *When setting up a new timer function, make sure the Wi-Fi In-Wall Switch
events). is connected to your home/office router, and that theWi-Fi In-Wall Switch is
plugged into a 120Vac wall outlet. The Wi-Fi In-Wall Switch will also
Mail Box - Welcome share any feedback on this App.
remember programmed timers when removed from power.
NOTE: If you preprogram it and move it to a different area with completely

EXPLORE THE TIMER FUNCTION

different WiFi signals, the Wi-Fi In-Wall Switch will attempt to connect to
one of these unsuccessfully. This will make the preprogrammed timer NOT
function. In this case, you may have to RESET the Wi-Fi In-Wall Switch and
set it to a router in the area.

EDITING THE PROGRAMMED TIMER

iOS
Enter editing mode
Programmable Timer - Setting On/ Off events.
Select ON time and OFF time. (EX: ON - 06:30PM OFF - 05:00AM)
Can also select what day(s) of the week it effects.
COUNTDOWN TIMER - You will select an ON date (EX: 03/29/17) and
time (EX: 07:30PM) and an OFF date (EX: 04/02/17) and time (EX:
Delete mode
05:00AM) Tap
ASTRONOMIC TIMER - Wi-Fi In-Wall Switch will turn ON/OFF at sunset or * When the device change
sunrise. Can also select what day(s) of the week it effects. color from white to yellow
HOLIDAY RANDOM - The Wi-Fi In-Wall Switch will turn ON/OFF at random
times based on three simple settings (Night, Day, All Day)
SECURITY RANDOM - The Wi-Fi In-Wall Switch will turn ON/OFF at random Android
times between a set of selected start and end dates and times.
Your phone
PROGRAMMABLE RANDOM - This icon increases or decreases the
time of your ON/OFF events by 30 minutes

PROGRAMMING THE TIMER

Tapping and holding
Tap
When the device change color from white to yellow
*
* The Wi-Fi In-Wall Switch will remember programmed
times even if the Wi-Fi Network is down.
Tap
Tap
* When the device change
color from white to yellow
Delete
Edit
Delete