TP-Link Omada EAP225 Installation Manual page 2

Option 3: Mounting the EAP on an Antenna
Note: Sector antenna is used as a demonstration below.
Step1:
Align the mounting tabs on the back
of the EAP with the slot of the
mounting bracket (for EAP). Push and
slide the EAP downward until it locks
into place.
Step2:
Align the mounting tabs on the
mounting bracket (for EAP) with the
four slots of the mounting bracket on
the antenna. Push and slide the EAP
downward until it locks into place.
Step3:
Connect the RF cables from the EAP
to the corresponding connectors on
the antenna.
Step4:
Attach the protective cap. Push and
slide the protective cap down over the
EAP until it firmly locks into place.
Sector or omni antennas need to be purchased additonally.
TL-ANT2415MS/TL-ANT5819MS/TL-ANT2410MO are available for the EAP.
Via PoE Switch
Connect an Ethernet cable from the PoE switch to the
ETHERNET port.
PoE Switch
Connect Cables
Step 1:
Firmly grasp the rear of the interface
cover and pull it downward.
Step 2:
Use an adequate Ethernet cable to
connect the LAN port. The length of
cable is up to 100m for steady
power supply. Shielded CAT5e (or
above) cable is recommended.
Step 3:
Attach the waterproof rubber insert
to the groove at the underside of
the device for waterproofing and
replace the cover until it firmly locks
into place.
Software Configuration
The EAP supports two configuring options:
To configure and manage mass EAPs via centralized controller software, please
refer to Option 1.
To configure a single EAP via a web browser directly, please refer to Option 2.
Option 1: Via EAP Controller
Step 1: Installing the EAP Controller
On the PC, download the EAP Controller installation file from
http://www.tp-link.com/en/download/EAP-Controller.html. Run the
file and follow the wizard to install the EAP Controller.
Step 2: Configuring the EAP Controller
Launch the EAP Controller and follow the step-by-step instructions
to complete the Quick Setup. After the wizard is finished, a login
screen will appear.
Step 3: Logging in to the EAP Controller
Enter the admin name and password you created and click Sign In.
Then you can further configure the EAP Controller.
For detailed configurations, please visit
http://www.tp-link.com/support to download the User Guide of
EAP Controller in the download center.
Power On
The EAP can be powered via the provided passive PoE adapter or a
PSE device (such as a PoE switch) .
Via Passive PoE Adapter
Connecting the PoE Adapter
Connect the EAP to a Power over Ethernet (PoE) adapter as follows:
PoE LAN
Ethernet cable length up to 100m
Option 2: Via Web Browser
Step 1: Connecting to the EAP Device
Power on the EAP and connect wirelessly by using the default SSID
(format: TP-Link_2.4GHz/5GHz_XXXXXX) printed on the product
label.
Step 2: Logging in to the EAP Device
Launch a web browser and enter http://tplinkeap.net in the address
bar. Use admin for both Username and Password to log in.
Step 3: Configuring the EAP device
Set up a new Username and Password for secure management
purpose. Modify the wireless parameters and reconnect your
wireless devices to the new wireless network.
For detailed configurations, please visit
http://www.tp-link.com/support to download the User Guide of
EAP in the download center.
Attention:
For EAP225-Outdoor, in EU member states and EFTA countries, the operation in
the frequency range 5150MHz - 5350MHz is only permitted indoors.
For EAP Controller, go to Access Point page and select the desired EAP to specify
the channel. For web browser, go to Wireless > Wireless Settings to specify the
channel.
AT BE BG CH CY CZ DE DK EE EL ES FI FR HR HU
IS IT LI LT LU LV MT NL NO PL PT RO SE SI
Mounting the PoE Adapter (Optional)
Note: To ensure the passive PoE adapter is attached most securely, it is
recommended to install the adapter with the Ethernet port facing
upward.
Step 1:
Remove the mounting bracket from the passive PoE Adapter.
Drill two holes on the wall and insert the plastic wall anchors
into the the holes. Secure the mounting bracket to the wall.
Make sure the shoulders at the corners of the mounting bracket
are on the outside and pointing upward.
Step 2:
Attach the passive PoE adapter to the mounting bracket (for
PoE Adapter) by sliding the adapter in the direction of the
arrows until it locks into place.
For technical support, User Guide and other information, please
visit http://www.tp-link.com/support, or simply scan the QR code.
The products of TP-Link partly contain software code developed by third parties, including software code subject
to the GNU General Public License ("GPL"). As applicable, the terms of the GPL and any information on obtaining
access to the respective GPL Code used in TP-Link products are available to you in GPL-Code-Centre under
IE
(http://www.tp-link.com/en/support/gpl/). The respective programs are distributed WITHOUT ANY WARRANTY and
SK UK are subject to the copyrights of one or more authors. For details, see the GPL Code and other terms of the GPL.