1. Manuals
  2. Brands
  3. Celect Manuals
  4. Thermostat
  5. CC852KIT
  6. Instruction manual

Celect CC852KIT Instruction Manual

Rf programmable thermostat
Hide thumbs
Table of Contents

Advertisement

Quick Links

C
ELECT
CC852KIT
RF Programmable Thermostat
for
CORONDO CONTROLS LTD
7 days Setting
BOLTON BL1 2PT
Instruction Manual
www.coronadocontrols.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CC852KIT and is the answer not in the manual?

Questions and answers

Related Manuals for Celect CC852KIT

Summary of Contents for Celect CC852KIT

  • Page 1 ELECT CC852KIT RF Programmable Thermostat CORONDO CONTROLS LTD 7 days Setting BOLTON BL1 2PT Instruction Manual www.coronadocontrols.com...

  • Page 2: Table Of Contents

    TABLE OF CONTENT A. Installation and Mounting ………………….. 3 1. Installation …………………………………… 3 2. Mounting …………………………………….. 4 3. Receiver Addressing………………………... 5 B. Key Interface…………………………………. 7 C. LCD Interface………………………………. ..8 D. Start/Reset …………………………………...9 E. Operation Mode …………………………….10 F. Time Setting Mode ………………………….11 G.
  • Page 3 K. Specification CC852KIT RF Programmable Thermostat Frequency: 868Mhz 1. The system includes one wireless thermostat controller Temperature Measurement: 0°C~40°C plus one RF receiver Plug. Accuracy: ±0.5°C 2. Transmits up to 20 meter indoor Temperature Controllable Range: 5°C~35°C 3. Communicates at 868MHz(Europe Standard) and Resolution: 0.5°C...

  • Page 4: Installation And Mounting

    1. Installation Location: J. Temperature Setting Transmitter: should be mounted on an inner wall ~1.5m Press once to activate the temperature above the floor in position where it is readily affected by setting. the setting temperature will be flashing. change of the room temperature with freely circulating air. Do not place the unit at a location where air circulation is Press to increase or decrease the setting...

  • Page 5: Mounting

    I. RF Address Matching 2. Mounting: Set the RF address in WT852T(Transmitter) by Mounting (Transmitter): - Pull out the battery drawer accessing internal setting. for “1” and for “0” for the digit . Press - Use a screwdriver to press For example, If you are going to set 11110011, on the spot to detach the front shell...

  • Page 6: Receiver Addressing

    3. Receiver Address Accessing H. Internal Setting Mode: 1. Pull out the door by using a screwdriver. Hold key to enter internal setting. 2. Set the RF address. The receiver RF address must Press to switch items and adjust value. match the transmitter RF address.
  • Page 7 Receiver LED Indication Comfort mode When the plug is powered, Econ the Red LED will be on. mode When the output is on, the Green LED will be on.

  • Page 8: Key Interface

    G. Program Setting Mode: B. Key Interface Press to enter program setting. i) Press to select weekday Press to confirm. ii) Press to select the program. P0 – P7 are the default programs and P8 – P15 are the editable programs. Press to confirm.

  • Page 9: Lcd Interface

    F. Time Setting Mode: C. LCD Interface Introduction Hold to go to time setting. 1.Cool to adjust “weekday”. i) Press 2.Heat Press to confirm. Comfort mode is running Econ mode is running 5.Override Mode to adjust “hour”. ii) Press 6.Defrost(<5°C) Press to confirm.

  • Page 10: Start/Reset

    D. Start/Reset: E. Operation Mode: Place 2 pcs AAA 1.5V alkaline batteries according to the polarities marked. Press key to switch between the 3 operation LCD display will be switched on. modes below. If there are any display or functional errors, 1.

Table of Contents