Table of Contents
Advertisement
Power save function
The second and minute hands stop automatically at 0:00 to save power when the
dial of the watch has not been exposed to light for a long time.
• The watch works normally even while saving power.
• However, automatic time reception is not executed while saving power.
• The power save function is not activated when the position of the crown is not
Canceling the power save function
The power save status ends and the hands return to normal indication as the dial
is exposed to light and power generation starts.
• After power saving of a long period of time, check the time and calendar of the
watch and adjust them if required.
Adjusting the time and calendar manually
1
Pull the crown out to position
The second hand indicates the alarm setting ( ON/OFF).
2
Rotate the crown to make the second hand point "ACT"
(0-second position).
• Each time you rotate the crown, the second hand moves as
follows:
Alarm setting ( ON/OFF) → ACT →
flight mode setting ( ON/OFF) → (back to the top).
3
Press and hold the button for 2 seconds or more.
• Release the button after the second hand swings left and right and
points "ACT" (0-second position).
4
Press the button to change the target to correct.
• Each time you press button , the target changes as follows.
Minute → hour/date → year/month → (back to the top)
• The hands and indications slightly move when selected to show
they become adjustable.
5
Rotate the crown to adjust the hand/indication.
• Minute/second hands and hour hand/date indication
synchronously move respectively.
• Change of date indication shows it just became AM. Take care the
time set is AM or PM.
• When you rotate the crown quickly a few times, the hands
and date indication will move continuously. To stop the rapid
movement, rotate the crown in either direction.
• Refer to
"Month and year
6
Repeat steps 4 and 5.
7
Push the crown in to position
time source to finish the procedure.
Month and year indications
Set the year and month with the position of the second hand.
"Month" corresponds to one of the 12
zones shown in the figure below.
Each number means month.
12
11
1
10
2
9
3
8
4
7
5
6
Actual year
2016 2020 2024 2028 2032
2017 2021 2025 2029 2033
2018 2022 2026 2030 2034
2019 2023 2027 2031 2035
.
1
indications" to set the year and month.
in accordance with a reliable
0
"Year" corresponds to the years
since leap year and is indicated with
markers in the zone of each month.
Years since leap year: 0
(Leap year)
Years since leap year: 1
Years since leap year: 2
Years since leap year: 3
0
1
2
3
Years since leap
Second hand position
year
0 (Leap year)
Hour marker
1st min. marker
1
2
2nd min. marker
3
3rd min. marker
Ex.: Position of the second hand when setting August 2018
You can find that the years since leap year of 2018 is "2"
from the table and the second hand must be set to the
2nd minute marker of August zone.
.
0
Troubleshooting
Checking and correcting the reference position
If the time or calender is not shown correctly even after proper reception of the
time info, check whether the reference position is correct.
• If the hands and indication do not reflect the correct reference position, the time
and calendar will not be indicated accurately even if the time info is received.
What is the reference position?
The base position of all hands and
calendar to properly indicate the various
functions of this watch.
• Hour, minute and second hands: 0 hour
00 minute 0 second
• Date indication: midway between "31"
and "1"
1
Pull the crown out to position
The second hand indicates the alarm setting ( ON/OFF).
2
Rotate the crown to make the second hand point the flight
mode setting ( ON/OFF).
• Each time you rotate the crown, the second hand moves as
follows:
Alarm setting( ON/OFF) → ACT →
flight mode setting ( ON/OFF) → (back to the top).
3
Press and hold the button for 5 seconds.
The hands and indication start to move to the current reference
positions stored in memory.
• Release the button as the second hand start to move.
4
Check the reference positions of them referring to the
illustration above.
Correct
Wrong
5
Pull the crown out to position
6
Press and release the button repeatedly to change the hand/
indication to be corrected.
• Each time you press the button, the target changes as follows.
Hour hand/date indication → minute/second hands →
(back to the top)
• The hands slightly move when selected to show they become
adjustable.
7
Rotate the crown to adjust the hand/indication.
• Minute/second hands and hour hand/date indication
synchronously move respectively.
• When you rotate the crown quickly a few times, the hand/
indication will move continuously. To stop the rapid movement,
rotate the crown in either direction.
8
Repeat steps 6 and 7.
9
Push the crown in to position
The watch keeps to indicate the reference position.
10
Press the button to finish the procedure.
• The hands and indication returns normal in 2 minutes without
pressing the button.
CITIZEN Bluetooth Watch W410 Instruction manual
Correct reference positions
12
9
6
.
1
Proceed to step 9 without adjusting the reference
position.
Proceed to step 5 and correct the reference position.
.
2
.
0
11/14
Advertisement
Table of Contents
