Doro PhoneEasy 508 Quick Start Manual

Doro PhoneEasy 508
®

Quick Start Guide

English
1
2 13
12
3 11
4 10
9
5
8
6 7
16 17 18
www.doro.com
1. Earpiece 11. End call /
Power on/off
2. Left selection
button 12. Arrow buttons
3. Call button 13. Right selection
button
4. Speed dials
14. Charging socket
5. Voice mail
15. Headset socket
6. Keypad lock
16. Loudspeaker
7. Silent /
Input method 17. Assistance button
8. Microphone 18. Battery cover
9. Torch shortcut 19. Lanyard hold
(not included)
10. Message shortcut
19
The items supplied with your phone might
vary depending on the software and
accessories available in your region or offered
by your service provider. You can obtain
additional accessories from your local Doro
dealer. The supplied accessories provide the
best performance with your phone.
Full user manual
For the full user manual please visit
www.doro.co.uk/support/ or contact our
Helpline.
1. GET STARTED
Installing the SIM card and battery
Important!
Turn off the phone and disconnect the
charger before removing the battery cover.
1 2 3
1. Remove the battery cover and the battery
if it is already installed.
2. Insert the SIM card by gently sliding it into
the holder. Make sure that the SIM card's
contacts are facing inwards and that the
cut off corner is pointing down. Take care
not to scratch or bend the contacts on the
SIM card.
3. Insert the battery by sliding it into the
battery compartment with the contacts
facing downwards to the right.
4. Replace the battery cover.
Charge the phone
CAUTION
Only use batteries, charger and accessories
that have been approved for use with
this particular model. Connecting other
accessories may be dangerous and may
invalidate the phone's type approval and
guarantee.
When the battery is running low,
displayed and a warning signal is heard.
• Connect the mains adapter to the wall
socket and to the charging socket y .
2. GET TO KNOW YOUR PHONE
Turn the phone on and off
1. Press and hold the red button
the phone to turn it on/off. Confirm with
Yes to power off.
2. If the SIM card is valid but protected with a
14
PIN code (Personal Identification Number),
15
PIN is displayed. Enter the PIN code and
press OK. Delete with Clear.
Note! If PIN and PUK codes were not
provided with your SIM card, please contact
your service provider.
Tip: It is recommended to remove the
protective plastic film from the display to
enhance the visibility.
Attempts: # shows the number of PIN
attempts left. When no more attempts
remain, PIN blocked is displayed. The SIM
card must now be unlocked with the PUK
code (Personal Unblocking Key).
1. Enter the PUK code and confirm with OK.
2. Enter a new PIN code and confirm with OK.
3. Re-enter the new PIN code and confirm
with OK.
Start-up wizard
When starting the telephone for the first time,
you can use the start-up wizard to set some
basic settings.
Tip: You can run the start-up wizard later if
you want.
Step-by-step instructions
The arrow (â) indicates next action in step-
by-step instructions. To confirm an action,
press OK. To select an item, scroll or highlight
the item using / and then press OK.
Enter text
• Press a numerical key repeatedly until
the desired character is shown. Wait a
few seconds before entering the next
character.
• Press for a list of special characters.
*
Select the desired character with
and press OK to enter it.
• Use / to move the cursor within the
text.
• Press to cycle upper case, lower case
#
and numerals.
• Press and hold to change writing
#
language.
Keypad lock
You can lock the keypad to prevent the keys
being accidentally pressed.
• Press and hold to lock/unlock the
*
keypad.
Activate keylock
1. Press Menu â Settings â Security â
Keypad lock:
• Auto keylock select the time delay for
automatic keypad locking.
• Unlock mode select Single key to
unlock the keypad with
tively with Dual key to lock/unlock with
right selection button (Name/Unlock)
4 and .
*
2. Press OK to confirm.
Change language, time and date
The default language is determined by the
SIM card. See Phone settings in the full
manual on how to change language, time and
date.
3. CALLS
Make a call
1. Enter the phone number including the
area code. Delete with Clear.
2. Press to dial. Press Abort to cancel
dialling.
3. Press to end the call.
Note! For international calls, always use +
before the country code for best operation.
Press twice for the international prefix +.
*
Make a call from the phonebook
1. Press Name to open the phonebook.
is
2. Use / to scroll through the
phonebook, or quick search by pressing
the key corresponding to the first letter of
the name.
3. Press Call to dial the selected entry, or
press Back to return to standby.
Receive a call
1. Press to answer, or press Silent to
switch off the ring signal and then Reject
on
to reject the call (busy signal).
Alternately, press
directly.
2. Press to end the call.
Volume control
Use / to adjust the sound volume
during a call. The volume level is indicated on
the display. See also Audio setup in the full
manual.
Silent
Silent is a fixed profile with keypad tone,
message tone and ring tone disabled, while
vibration, tasks and alarm are unchanged.
• Press and hold
silent.
Call options
During a call the soft keys (
to additional functions.
Speed dial
Use – , and
A B 0
entry from standby.
• Press and hold the corresponding button
to dial.
Add speed dial numbers
1. Press Menu â Settings â Calls â
Speed dial.
2. Select â Add an select an entry from
A
the phonebook.
3. Press OK to confirm.
4. Repeat to add speed dial entries for
buttons , ,
B 0 2
SOS calls
As long as the phone is switched on, it is
always possible to place an SOS call by
entering the main local emergency number
/
for your present location followed by
Call log
Received, missed, and dialled calls are saved
in a combined call log. 20 calls of each type
can be stored in the log. For multiple calls
related to the same number, only the most
recent call is saved.
1. Press .
2. Use / to scroll through the call log.
= Received call
= Dialled call
= Missed call
3. Press to dial, or Options.
4. PHONEBOOK
The Phonebook can store 100 entries with 3
phone numbers in each entry.
Add contact
alterna-
1. Press Menu â Phonebook â
*
-New contact- â Add.
2. Enter a Name for the contact, see
Enter text. Delete with Clear.
3. Use / to select
Home or
phone number(s) including the area code.
4. When done, press Save.
ICE (In Case of Emergency)
First responders can access important
information such as medical information
from the victim's phone
emergency. In the event of a trauma, it is
critical to have this information as early
as possible to increase the chances of
survival. All fields are optional, but the more
information provided the better.
1. Press Menu â ICE.
2. Use / to scroll the list of entries.
3. Press Edit to add or edit information in
each entry. Delete with Clear.
4. Press Save when done.
See Phonebook/ICE in the full manual.
5. ASSISTANCE BUTTON
The assistance button allows easy access to
contact your predefined help numbers should
you need help. Make sure that the assistance
to reject the call function is activated before use. See the
full manual on how to activate, how to enter
recipients in the numbers list, and how to edit
the text message.
Important!
Always inform recipients in the Number
list that they are listed as your assistance
contacts.
Make an assistance call
1. When help is needed, press and hold the
assistance button for 3 seconds, or press
it twice within 1 second.
The assistance call begins after a delay of
to activate/deactivate
#
5 seconds. In this time you can prevent a
possible false alarm by pressing
2. An assistance text message (SMS) is sent
) give access
to all recipients.
3. The first recipient in the list is dialled.
If the call is not answered within 25
– to speed dial an
2 9
seconds, the next number is dialled.
Dialling is repeated 3 times or until the
call is answered, or until
CAUTION
When an assistance call is activated the
phone is pre-set to handsfree mode. Do
not hold the device near your ear when
the handsfree mode is in use, because the
volume may be extremely loud.
Note! Some private security companies can
accept automatic calls from their clients.
– .
Always contact the security company before
9
using their phone number.
See Assistance settings in the full manual.
.
6. MESSAGES
Create and send text messages
1. Press shortcut button
Alternatively press Menu â Messages â
Write message.
2. Write your message, see Enter text, then
press To.
3. Select a recipient from Phonebook.
Alternatively, select Enter number to add
recipient manually and press Done.
4. Select Add to add more recipients.
You can modify the recipients by selecting
one and press Options â Edit/Delete/
Delete all.
5. When done, press Send.
7. CONNECTIVITY
Bluetooth
Mobile,
Office, and enter the
You can connect wirelesses to other
Bluetooth
headsets or other phones.
Important!
When you are not using Bluetooth
tivity, turn off Function on/off or Visibility. Do
not pair with an unknown device.
in case of
Activate Bluetooth
1. Press Menu â Settings â Bluetooth â
Function on/off â On.
2. Press OK to confirm.
Visibility
1. Press Menu â Settings â Bluetooth â
Visibility â On.
2. Press OK to confirm.
Search device
1. Press Menu â Settings â Bluetooth â
Search device.
2. Select a device from the list and press
Bond to connect. If Bluetooth
enabled, press Yes to activate.
3. Press OK to confirm.
.
is pressed.
.
®
compatible devices such as
®
connec-
®
®
® is not