RCA RCRPST06GR Owner's Manual
RCA RCRPST06GR Owner's Manual

RCA RCRPST06GR Owner's Manual

Advertisement

Available languages

Available languages

RCRPST06GR US 00 2601
4.
When you've finished entering

Step 2: Program your remote

the five-digit code, keep holding
down the device key and look at
the POWER key.
To use this universal remote with your home entertainment
system, first you need to program it to control your devices.
Is the POWER key
There are four ways you can program the universal remote to
illuminated?
RCRPST06GR
operate your devices. Try them in the order listed.
YES: You're done! You've programmed this device key.
The Direct Code Entry lets you enter a code from the
NO, it blinked four times and turned off: You have
accompanying code list for your brand of device.
either entered a code number that is not in the code lists
Universal Remote Control
The Brand Code Search searches through the codes for
or missed a step in the code entry procedure. Try step 3
Owner's Manual
again.
select brands of devices.
Manual del Propietario (parte posterior)
The Auto Code Search goes automatically through all the
NOTES
codes for the device you're trying to control.
Test the remote with the device to make sure the device
FCC Statement:
key is programmed with the correct code for maximum
The Manual Code Search lets you manually go through
This device complies with part 15 of the FCC Rules. Operation is subject to the
functionality. If some features don't work, try a different code
all the codes for the device you're trying to control.
following two conditions: (1) This device may not cause harmful interference,
in the list.
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Remember to enter the code for future reference in the box
Note: This equipment has been tested and found to comply with the limits
provided in the Code Retrieval section of this manual.
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference

Direct Code Entry

If your brand isn't listed in the code list, use one of the Code
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
Direct Code Entry lets you enter a code from the accompanying
Search methods to program the remote control. (Refer to the
the instructions, may cause harmful interference to radio communications.
code list for your brand of device.
Auto and Manual Code Search methods.)
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
If you release the device key any time during the Direct Code
on, the user is encouraged to try to correct the interference by one or more of
TIP: Each device key is associated with a type of device—
Entry procedure, the POWER key blinks four times, and the
the following measures:
the TV is preset to search for TVs, SATELLITE/CABLE for
process is exited. The last programmed code under the
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
satellite receivers or cable boxes, STREAM1/2 for streaming
device key is retained.
Connect the equipment into an outlet on a circuit different from that to
players, DVD/VCR for DVD players, and AUDIO/SOUNDBAR
which the receiver is connected.
for audio devices and soundbars. To program a device key
Consult the dealer or an experienced radio/TV technician for help.
for a different type of device, see the Changing a Key's
Caution: Any Changes or modifications not expressly approved by the party

Brand Code Search

responsible for compliance could void the user's authority to operate this
Device Type section.
equipment.
The Brand Code Search goes through only the codes for one of
Industry Canada Regulatory Information
CAN ICES-3 (B)/NMB-3 (B)
the select brands listed in the accompanying code list. If your
Avis d'Industrie Canada
brand of device is listed, this search can be very quick and easy.
CAN ICES-3 (B)/NMB-3 (B)
1.
Manually turn on the device you
TIPS: Each device key is associated with a type of device—
SAVE THIS MANUAL AND THE CODE LISTS!
want to control.
Remote controls can sometimes lose their programming when
the TV is preset to search for TVs, SATELLITE/CABLE for
you change the batteries. Make sure you keep the manual and
satellite receivers or cable boxes, STREAM1/2 for streaming
code lists in a safe place so that you can reprogram the remote if
players, DVD/VCR for DVD players, and AUDIO/SOUNDBAR
you need to.
for audio devices and soundbars. To program a device key
Tip: This remote is already programmed to operate most RCA-
2.
for a different type of device, see the Changing a Key's
Find the Code List that came with
branded TVs, DVD players, and satellite receivers. Just press
Device Type section.
the corresponding key—DVD/VCR for a DVD player, TV for a
the remote. Locate the section for
television, SATELLITE/CABLE for a satellite receiver.
the type of device you're trying to
To exit without saving a new code at any point in the Brand
program, and find your brand in
Code Search, press the CLEAR key.

Step 1: Install your batteries

that section. Circle the codes for
your brand and keep them handy.
Your universal remote requires two AAA alkaline batteries (not
1.
included).
Manually turn on the device you
want to control.
To install the batteries:
3.
Press and hold the device key you want to program (the
1.
Remove the battery compartment cover.
POWER key illuminates).
2.
Insert the batteries, matching the batteries to the (+) and (–)
While you're holding down the device key, use your other
marks inside the battery compartment.
hand enter the first five-digit code for your brand in the
2.
code list (the POWER key turns off after the first digit).
Find your device's brand in the
3.
Push the battery cover back into place.
STREAM1
STREAM2
Brand Code list section of the
AUX1
POWER
AUX2
accompanying code list. Circle
Battery Precautions:
TV
SATELLITE
CABLE
DVD
VCR
SOUNDBAR
AUDIO
STREAM1
STREAM2
STREAM1
AUX1
POWER
STREAM2
AUX2
AUX1
POWER
POWER
AUX2
the number for your brand and
• Do not mix old and new batteries.
SATELLITE
DVD
AUDIO
TV
CABLE
SATELLITE
DVD
VCR
SOUNDBAR
AUDIO
TV
GUIDE•HOME
CABLE
VCR
SOUNDBAR
OPTIONS
keep the list handy.
CLEAR
INFO
• Do not mix alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium) batteries.
GUIDE•HOME
GUIDE•HOME
CLEAR
OPTIONS
INFO
• Always remove old, weak or worn-out batteries promptly and
CLEAR
OPTIONS
INFO
recycle or dispose of them in accordance with Local and National
VOL
OK
CH
Regulations.
3.
VOL
OK
CH
Press and hold the device key you want to program. The
VOL
OK
CH
Battery Saver
MUTE
MENU
GO BACK
POWER key illuminates.
Your universal remote control saves battery power by automatically
1
2
3
MUTE
GO BACK
While you're holding down the device key, use your other
MENU
turning off if any key is pressed for more than 60 seconds. This
MUTE
GO BACK
4
5
6
MENU
hand to press and hold the remote's POWER key at the
saves your battery life should your remote get stuck in a place
1
7
8
2
3
9
1
2
3
4
5
6
same time. The POWER key turns off.
where the keys remain depressed, such as between sofa cushions.
ENTER
0
INPUT
4
5
6
7
8
9
REVERSE
PLAY
FORWARD
ENTER
0
INPUT
7
8
9
RECORD
STOP
PAUSE
ENTER
0
INPUT
REVERSE
PLAY
FORWARD
STREAM1
STREAM2
AUX1
POWER
POWER
AUX2
REVERSE
PLAY
FORWARD
RECORD
STOP
PAUSE
SATELLITE
DVD
AUDIO
RECORD
STOP
PAUSE
TV
CABLE
VCR
SOUNDBAR
GUIDE•HOME
CLEAR
OPTIONS
INFO
VOL
OK
CH
MUTE
GO BACK
MENU
1
2
3
4
5
6
7
8
9
STREAM1
AUX1
POWER
STREAM2
AUX2
SATELLITE
DVD
AUDIO
TV
CABLE
VCR
SOUNDBAR
4.

Auto Code Search

STREAM1
STREAM2
Wait until the POWER key comes on
STREAM1
STREAM2
AUX1
POWER
POWER
POWER
AUX2
AUX1
POWER
POWER
POWER
GUIDE•HOME
AUX2
CLEAR
OPTIONS
INFO
and stays on. Then release both keys.
The Auto Code Search goes automatically through all the
SATELLITE
DVD
AUDIO
SATELLITE
DVD
AUDIO
TV
CABLE
VCR
SOUNDBAR
TV
CABLE
VCR
SOUNDBAR
codes for the device you're trying to control. When you find
the one that operates your device, you can stop the search and
VOL
OK
CH
store that code.
GUIDE•HOME
GUIDE•HOME
OPTIONS
CLEAR
OPTIONS
INFO
CLEAR
INFO
5.
Look at the numbers you circled for
MUTE
GO BACK
MENU
TIPS: Each device key is associated with a type of
your device's brand code number.
1
2
3
device—the TV is preset to search for TVs, SATELLITE/
Press those numbers on the remote
4
5
6
CABLE for satellite receivers or cable boxes, STREAM1/2
VOL
OK
CH
VOL
OK
CH
keypad.
7
8
9
for streaming players, DVD/VCR for DVD players, and
0
ENTER
INPUT
AUDIO/SOUNDBAR for audio devices and soundbars. To
REVERSE
PLAY
FORWARD
program a device key for a different type of device, see the
RECORD
STOP
PAUSE
Changing a Key's Device Type section.
MUTE
GO BACK
MUTE
MENU
GO BACK
MENU
6.
Point the remote directly at the
To exit without saving a new code at any point in the Auto
1
2
3
front panel of the device you want
1
2
3
Code Search, press the CLEAR key.
to control. Press POWER on the
4
5
6
4
5
6
remote and wait 2 seconds. The
7
8
9
7
8
9
remote is testing a single code for
1.
Manually turn on the device you
0
ENTER
0
INPUT
your device's brand.
ENTER
INPUT
POWER
want to control.
REVERSE
PLAY
FORWARD
Did your device turn off?
REVERSE
PLAY
FORWARD
RECORD
STOP
PAUSE
YES: Press the STOP key to store the code. You're done!
RECORD
STOP
PAUSE
You've programmed this device key.
2.
Press and hold the device key you want to program. The
NO: Press POWER again. The remote tests the next code
POWER key illuminates.
for your brand.
While you're holding down the device key, use your other
Keep pressing POWER every 2 seconds until your device
hand to press and hold the remote's POWER key at the
turns off. When it does, press STOP.
same time. The POWER key turns off.
NOTES
STREAM1
STREAM2
STREAM1
STREAM2
AUX1
POWER
POWER
AUX2
AUX1
POWER
POWER
AUX2
Throughout the programming of each key, be sure to keep
SATELLITE
DVD
AUDIO
SATELLITE
DVD
AUDIO
TV
CABLE
VCR
SOUNDBAR
TV
CABLE
VCR
SOUNDBAR
the remote pointed at the IR sensor of the device you are
currently programming the remote to control.
GUIDE•HOME
GUIDE•HOME
OPTIONS
OPTIONS
Test the remote with the device to make sure the device
CLEAR
INFO
CLEAR
INFO
key is programmed with the correct code for maximum
3.
Wait until the POWER key comes
STREAM1
STREAM2
functionality. If some features don't work, try a different
AUX1
POWER
POWER
POWER
AUX2
on and stays on. Then release
code. See the "Testing the Code for Maximum Functionality"
both keys.
VOL
OK
CH
VOL
SATELLITE
OK
DVD
CH
AUDIO
TV
CABLE
VCR
SOUNDBAR
section below for more information.
During the Brand Code Search, the remote ignores
GUIDE•HOME
OPTIONS
keypresses that aren't part of the search.
CLEAR
INFO
4.
MUTE
MENU
GO BACK
MUTE
MENU
GO BACK
The search times out after two minutes (the POWER key
Point the remote directly at the
blinks four times and turns off, and the last programmed
front panel of the device you
1
2
3
1
2
3
code under that device key is retained).
want to control. Press PLAY on
4
5
6
4
5
6
the remote and wait 5 seconds.
VOL
OK
CH
The POWER key blinks four times and turns off when the
The remote is testing a batch of
7
8
9
7
8
9
remote has gone through all the codes. The remote exits the
10 codes on your device.
ENTER
0
INPUT
ENTER
0
PLAY
INPUT
Brand Code Search. If your device hasn't turned off yet, try a
different search method.
Did your device turn off?
REVERSE
PLAY
FORWARD
MUTE
GO BACK
REVERSE
PLAY
MENU
FORWARD
YES: Go to step 5.
RECORD
STOP
PAUSE
RECORD
STOP
PAUSE
1
2
3
NO: Press PLAY again. The remote tests the next batch of
4
5
6
10 codes.
Testing the Code for Maximum
7
8
9
Functionality
Keep pressing PLAY every 5 seconds until your device turns
ENTER
0
INPUT
off.
1. Try a variety of the device's functions with the
REVERSE
PLAY
FORWARD
remote. If some device features don't work, go to
the next step to try a different code.
5.
When your device turns off, press
RECORD
STOP
PAUSE
the REVERSE key on the remote
2. Repeat the Brand Code Search from the beginning. When
and wait at least 2 seconds.
the device turns off for the first time, don't press the STOP
The remote tries the last of the
key, which would store the same code. Instead, with the
previous ten codes.
unit now off, continue to press the POWER key repeatedly
until the unit turns back on.
Did your device turn on?
YES: Press the STOP key. You're
3. Once the unit turns back on, you have found another code
that operates the device. Press the STOP key.
done! You've programmed this
device key.
4. Test the key's functionality again by attempting to control
NO: Press REVERSE again. The remote tests the next
a variety of the device's functions. If the code that has
code in the batch.
been stored controls the majority of the device's functions,
programming is complete. If the code stored does not give
Keep pressing REVERSE every 2 seconds until your device
maximum functionality, try another code.
turns back on. When it does, press STOP.
STREAM1
STREAM2
AUX1
POWER
POWER
AUX2
Note: If you accidentally press the REVERSE key after your
SATELLITE
DVD
AUDIO
device turns on, press the FORWARD key. Then, wait two
TV
CABLE
VCR
SOUNDBAR
seconds to see if your device turns off again.
GUIDE•HOME
OPTIONS
CLEAR
INFO
VOL
OK
CH
MUTE
MENU
GO BACK
1
2
3
4
5
6
7
8
9
2.
NOTES
Press and hold the device key you want to program. The

Tour of the Remote

POWER key illuminates
Throughout the programming of each key, be sure to keep
the remote pointed at the IR sensor of the device you are
While you're holding down the device key, use your other
currently programming the remote to control.
hand to press and hold the remote's POWER key at the
In most cases, the keys on
same time. The POWER key turns off.
this remote perform the same
Test the remote with the device to make sure the
functions as the keys on your
device key is programmed with the correct code for
original remotes once you've
maximum functionality. If some features don't work, try
STREAM1
AUX1
POWER
POWER
STREAM2
AUX2
STREAM1
POWER
POWER
STREAM2
programmed this remote to
AUX1
AUX2
a different code. See the "Testing the Code for Maximum
operate your components.
Functionality" section below for more information.
TV
SATELLITE
CABLE
VCR
DVD
SOUNDBAR
AUDIO
SATELLITE
DVD
AUDIO
TV
CABLE
VCR
SOUNDBAR
Many keys on this remote
have other functions as well.
During the Auto Code Search, the remote ignores
keypresses that aren't part of the search.
GUIDE•HOME
OPTIONS
GUIDE•HOME
CLEAR
INFO
CLEAR
OPTIONS
INFO
Illuminated POWER key
serves as an indicator light to
The search times out after two minutes (the POWER key
3.
STREAM1
STREAM2
Wait until the remote's POWER key
AUX1
POWER
POWER
POWER
AUX2
provide feedback.
blinks four times and turns off, and the last programmed
comes on and stays on. Then release
code under that device key is retained).
OK
SATELLITE
DVD
AUDIO
both keys.
VOL
CH
VOL
TV
CABLE
OK
VCR
CH
SOUNDBAR
Device keys (TV, SATELLITE/
CABLE, DVD/VCR, AUDIO/
The POWER key blinks four times and turns off when the
SOUNDBAR, STREAM1/
remote has gone through all the codes. The remote exits
GUIDE•HOME
OPTIONS
CLEAR
INFO
AUX1, STREAM2/AUX2) put
4.
the Auto Code Search. If your device hasn't turned off yet,
Point the remote directly at the front panel of the device you
MUTE
GO BACK
MUTE
GO BACK
MENU
MENU
the remote in the right mode
want to control. Press POWER on the remote and wait 2
try a different search method.
to control your device.
seconds. The remote is testing a single code for your device.
1
2
3
1
2
3
4
5
6
4
VOL
5
OK
6
CH
The purple keys (STREAM1/2,
Did your device turn off?
Testing the Code for Maximum
GUIDE•HOME, OPTIONS/
7
8
9
7
8
9
YES: Press the STOP key to store
INFO, MENU, GO BACK)
Functionality
ENTER
0
INPUT
ENTER
0
INPUT
the code. You're done! You've
are the most used keys for
MUTE
GO BACK
1. Try a variety of the device's functions with the
REVERSE
PLAY
FORWARD
programmed this device key.
REVERSE
PLAY
MENU
FORWARD
streaming player.
remote. If some device features don't work, go to
RECORD
STOP
PAUSE
NO: Press POWER again. The
GUIDE•HOME puts the remote
RECORD
1
STOP
2
PAUSE
3
the next step to try a different code.
POWER
remote tests the next code for
in guide mode for satellite
4
5
6
2. Repeat the Auto Code Search Method from the beginning.
your device.
receivers or cable boxes, and
When your device turns off, do not stop searching.
7
8
9
accesses the home screen for
Keep pressing POWER every 2
Instead, with the unit now off, continue to press the PLAY
0
streaming players.
seconds until your device turns off.
ENTER
INPUT
key every 5 seconds until the unit turns back on.
When it does, press STOP.
REVERSE
PLAY
FORWARD
CLEAR exits remote
3. Once the unit turns back on, press the REVERSE key on the
programming; it also
remote every 2 seconds until your device turns off again.
TIP: Because there are so many codes, you may have to press
RECORD
STOP
PAUSE
performs the same functions
When your device turns off again, press the STOP key.
the POWER key many times—possibly hundreds of times.
as on your original remotes.
4. Test the key's functionality again by attempting to control
a variety of the device's functions. If the code that has
Arrow keys act as navigation
NOTES
been stored controls the majority of the device's functions,
keys in device guides and
Throughout the programming of each key, keep the remote
programming is complete. If the code stored does not give
menu systems.
maximum functionality, try another code.
pointed at the IR sensor of the device you are programming
the remote to control.
The INPUT — (dash) key
has three functions: (1) it
Test the remote with the device to make sure the device
key is programmed with the correct code for maximum
toggles through all the video

Manual Code Search

functionality. If some features don't work, try a different
sources connected to your
The Manual Code Search lets you go one-by-one through all the
code. See the "Testing the Code for Maximum Functionality"
TV; (2) when the remote is
codes for the device you're trying to control. When you find the
in VCR mode, this button
section below for more information.
one that operates your device, you can stop the search and store
toggles between VCR and
During the Manual Code Search, the remote ignores
that code.
the TV input; (3) when you're
keypresses that aren't part of the search.
entering digital channel
TIPS: The Manual Code Search method may take a long time
The search times out after two minutes (the POWER key
numbers directly, this button
because the remote searches through all of the codes in
blinks four times and turns off, and the last programmed
lets you separate the main
its memory one-by-one. If your brand is listed in the Brand
code under that device key is retained).
channel number from the
Codes or the Code Lists, first try the Brand Code Search or
The POWER key blinks four times and turns off when the
sub-channel number (such
the Direct Code Entry method.
remote has gone through all the codes. The remote exits the
as 59.1).
Brand Code Search. If your device hasn't turned off yet, try a
Each device key is associated with a type of device—the TV
different search method.
Red, green, yellow, and
is preset to search for TVs, SATELLITE/CABLE for satellite
blue keys access additional
receivers or cable boxes, STREAM1/2 for streaming players,
features on your cable box,
DVD/VCR for DVD players, and AUDIO/SOUNDBAR for

Testing the Code for Maximum Functionality

satellite receiver, or Blu-ray
audio devices and soundbars. To program a device key for
1. Try a variety of the device's functions with the
disc player (see your device
a different type of device, see the Changing a Key's Device
remote. If some features of your devices don't work,
manual for details).
Type section.
go to the next step to try a different code.
To exit without saving a new code at any point in the Manual
2. Repeat the Manual Code Search and Entry Method from
Code Search, press the CLEAR key.
the beginning. When the device turns off for the first time,
IMPORTANT
don't press the STOP key, which would store the same
Because this remote controls more than one device, you
code. Instead, with the unit now off, continue to press the
must first "tell" the remote which device you wish to
1.
POWER key repeatedly until the unit turns back on.
Manually turn on the device you
operate. That means, if you wish to operate your TV, you
want to control.
3. Once the unit turns back on, you have found another code
must first press the TV key to put the remote in the TV
that operates the device. Press the STOP key.
Mode. The remote stays in that device mode until you press
4. Test the key's functionality again by trying a variety of
a different device key. For example, if your remote is in TV
functions. If the code controls the majority of the device's
Mode and you want to operate the DVD player, you must
functions, programming is complete. If the code stored
press the DVD/VCR key to change device modes.
does not give maximum functionality, try another code.
Channel Lock

Advanced Functions

Channel lock automatically sends channel commands, like the
CH, GO BACK, and 0–9 number keys, to your satellite receiver,
cable box, or digital TV converter when you're in TV mode.
Changing A Key's Device Type
This can save you keypresses if you use a device other than
your TV to change channels.
Each device key is associated with a type of device—the TV is
STREAM1
POWER
STREAM2
To turn channel lock on:
AUX1
AUX2
preset to search for TVs,
SATELLITE/CABLE
for satellite receivers
or cable boxes,
STREAM1/2 for
streaming players, DVD/VCR for
1.
Press and hold the device key for the device you use to
SATELLITE
DVD
AUDIO
DVD players or VCRs, and AUDIO/SOUNDBAR for audio devices
change channels. While you're holding down this device
TV
CABLE
VCR
SOUNDBAR
and soundbars. To program these keys to control a different kind
key, use your other hand to press and hold the remote's
CH up key at the same time.
of device, you have to reassign them first.
2.
Wait until the remote's POWER key comes on and stays on.
GUIDE•HOME
Reassigning the DVD/VCR Key to Control a VCR
OPTIONS
CLEAR
INFO
Then release both keys.
The DVD/VCR key defaults to control a DVD player. If you want
3.
Press ENTER to lock channel commands to this device.
the DVD/VCR key to control a VCR, you must reassign it.
1.
Press and hold the DVD/VCR key. The POWER key
To turn channel lock off:
illuminates. Keep holding down the DVD/VCR key.
1.
Press and hold the TV key. While you're holding down the
VOL
OK
CH
2.
While holding down the DVD/VCR key, press and release the
TV key, use your other hand to press and hold the remote's
number 2 key on the keypad. The POWER key turns off.
CH down key at the same time.
3.
Release the DVD/VCR key. The POWER key blinks two times
2.
Wait until the remote's POWER key comes on and stays on.
and then turns off. The DVD/VCR key is now set to control a
Then release both keys.
VCR.
MUTE
GO BACK
3.
Press ENTER to start changing channels with your TV.
MENU
4.
Follow the directions in the auto, brand, direct entry, or manual
code search to program the DVD/VCR key for your VCR.
1
2
3
Reassigning the AUDIO/SOUNDBAR Key To Control
4
5
6

Code Retrieval

Other Devices
The AUDIO/SOUNDBAR key defaults to control an audio device
Once you've programmed the remote to control your devices,
7
8
9
or soundbar. If you want the AUDIO/SOUNDBAR key to control
you may want to record the codes for future reference. If you
a different device (an additional TV, DVD, satellite or cable box,
used the Direct Code Entry method, this is easy. Just find
ENTER
0
INPUT
for example), you must reassign it.
the codes you entered and make a note of them in the boxes
below. If you used one of the Code Search methods to program
REVERSE
PLAY
FORWARD
1.
Press and hold the AUDIO/SOUNDBAR key. The POWER key
turns on.
your remote or if you used the Direct Entry method but don't
remember the code, you will need to retrieve each device's
2.
While holding down the AUDIO/SOUNDBAR key, press and
RECORD
STOP
PAUSE
five-digit code. Retrieving the actual code and writing it down
release the number key on the keypad for the device you
will save you time if you ever need to program the remote
wish to control (see the chart below). The POWER key turns
again. If the codes are recorded, you can use the Direct Entry
off.
method to reprogram your remote to control your devices,
which is quick and easy.
AUDIO/SOUNDBAR KEY CONTROLS:
1.
Press and hold the device key
STREAM1
POWER
POWER
POWER
STREAM2
AUX1
AUX2
(TV, SATELLITE/CABLE, DVD/VCR,
Additional TV
press 1
AUDIO/SOUNDBAR, STREAM1/
SATELLITE
DVD
AUDIO
VCR or DVR
press 2
TV
CABLE
VCR
SOUNDBAR
AUX1, STREAM2/AUX2) whose
code you wish to retrieve. The
Additional DVD
press 3
GUIDE•HOME
OPTIONS
POWER key illuminates. Keep
CLEAR
INFO
Audio device or soundbar
press 4
pressing the device key.
Additional satellite, cable box or
press 5
2.
While holding the device key down, press and hold the
streaming player
INFO key. The POWER key turns off. After holding down
Actual model may vary from
VOL
OK
CH
both keys for three seconds, the POWER key turns back on.
illustration
3.
Release both keys. The POWER key remains on.
3.
Release the AUDIO/SOUNDBAR key. The POWER
4.
Starting with the number 1 key, press and release each
key blinks two times and then turns off. The AUDIO/
MUTE
number key on the keypad in the following order: 1-9, then
GO BACK
SOUNDBAR key is now set to control the device type you
MENU
0. The number that causes the POWER key to blink is the
selected.
1
first number of the code. As you find each number of the
2
3
4.
Follow the directions in the auto, brand, direct entry, or
4
code, write it down for future reference.
5
6
manual code search to program the AUDIO/SOUNDBAR
Note: All TV codes begin with the number 1; all VCR and DVR
7
8
9
key.
codes begin with the number 2; all DVDs, the number 3; all
ENTER
0
INPUT
audio devices, the number 4; and all satellite receivers, cable
boxes, streaming players and DTV converters, the number 5.
REVERSE
PLAY
FORWARD

Volume Punch-Through

5.
Repeat step 4 until you have retrieved all five numbers in
Volume punch-through allows the VOL and MUTE keys, when
RECORD
STOP
PAUSE
the code. After the fifth number is retrieved, the POWER
pressed in
SATELLITE/CABLE,
DVD/VCR, or STREAM1/2 modes,
key blinks briefly, then turns off.
to "punch through" to TV or AUDIO/SOUNDBAR. Volume
punch-through occurs automatically and allows you to control
TIP: To exit the Code Retrieval Mode at any time, press the
the volume without exiting the current mode. (If the DVD/VCR
CLEAR key.
key has been programmed with a TV code, volume can punch
Note: If you press an invalid key during the Code Retrieval
through to this device as well.)
process, the remote will not respond. If you do not press a
Notes: Volume punch-through does not occur in cases where
valid Code Retrieval key (TV, SATELLITE/CABLE, DVD/VCR,
the component code has its own volume/mute controls, such
AUDIO/SOUNDBAR, STREAM1/AUX1, STREAM2/AUX2,
as some satellite receivers.
INFO, CLEAR), Code Retrieval times out after 15 seconds. The
Volume punch-through sends volume commands to the last
POWER key blinks four times, and then turns off.
device you were controlling, either TV or AUDIO/SOUNDBAR,
before the active device. For example, if you were controlling
the TV before you started controlling your DVD player, the
volume commands will "punch through" to the TV while
you're in DVD/VCR mode.
Problem: The POWER key does not light when you press a key.
TV CODE
SATELLITE/CABLE CODE
You may have pressed an invalid key for the mode the remote is in.
1
5
Make sure the remote is in the correct mode by pressing the
corresponding device key (TV, SATELLITE/CABLE, DVD/VCR,
AUDIO/SOUNDBAR, STREAM1/AUX1, STREAM2/AUX2). This
tells the remote which device to operate.
SAT
CABLE
STREAMING PLAYER
Make sure the batteries are fresh and are properly installed.
Replace the batteries with two new AAA batteries, if necessary
DVD/VCR CODE
AUDIO/SOUNDBAR CODE
(see the Battery Installation section).
Problem: The remote will not change channels on device.
Make sure the remote is in the correct mode by pressing the
corresponding device key (TV, SATELLITE/CABLE, DVD/VCR,
DVD
VCR
AUDIO RECEIVER
SOUNDBAR
AUDIO/SOUNDBAR, STREAM1/AUX1, STREAM2/AUX2). This
tells the remote which device to operate.
STREAM1/AUX1 CODE
STREAM2/AUX2 CODE
Press the ENTER key after you enter a channel number.
Remove any obstacles between the remote and the device. Make
sure to aim the remote at the IR sensor on the device.
Problem: The device's menu does not appear on the TV screen.
Make sure you have connected the device to your TV properly and
STREAMING PLAYER
DVD
TV
STREAMING PLAYER
DVD
TV
SATELLITE/CABLE
DVR/VCR
SATELLITE/CABLE
DVR/VCR
selected the correct input. (See your devices' Owner's Manuals for
proper connection procedures.)
Make sure the remote is in the correct mode by pressing the
corresponding device key (TV, SATELLITE/CABLE, DVD/VCR,
AUDIO/SOUNDBAR, STREAM1/AUX1, STREAM2/AUX2). This
tells the remote which device to operate.
Menu access isn't supported for all brands. You may need to use
your original remote control to access menu functions for some
devices.
For more information, please visit www.RCAAudioVideo.com

Troubleshooting

Consumer Help Line: 1-800-420-7968
Care and Maintenance
Problem: The remote does not operate your device.
• Keep the remote dry. If it gets wet, wipe it dry immediately.
Make sure the remote is in the correct mode by pressing the
• Use and store the remote only in normal temperature environments.
corresponding device key (TV, SATELLITE/CABLE, DVD/VCR,
• Handle the remote gently and carefully. Don't drop it.
AUDIO/SOUNDBAR, STREAM1/AUX1, STREAM2/AUX2). This
• Keep the remote away from dust and dirt.
tells the remote which device to operate.
• Wipe the remote with a damp cloth occasionally to keep it looking new.
Remove any obstacles between the remote and the device. Make
• Modifying or tampering with the remote's internal devices can cause
sure you're aiming the remote at the device's IR sensor.
malfunction and invalidate its warranty.
Make sure the batteries are fresh and are properly installed.
Replace the batteries with two new AAA batteries, if necessary
(see the Battery Installation section).
Limited Lifetime Warranty
Problem: The remote can't be programmed to operate your
device.
Voxx Accessories Corporation (the "Company") warrants to you the
If you are testing the remote while programming it, you may be
original retail purchaser of this product that should it, under normal use
too far away from the device or at a wrong angle. There must be
and conditions, be proven defective in material or workmanship during its
an unobstructed path between the remote and the IR sensor on
lifetime while you own it, such defect(s) will be repaired or replaced (at the
the device. Move closer and make sure you point the remote at the
Company's option) without charge for parts and repair labor.
device you're trying to control.
To obtain repair or replacement within the terms of the warranty, the product
If you're using the Direct Entry programming method to enter
is to be delivered with proof of warranty coverage (e.g. dated bill of sale),
specification of defect(s), transportation prepaid, to an approved warranty
the codes for your brand and the unit is still not functioning
properly, try the auto, brand, or manual search method.
station. For the location of the nearest warranty station to you, call toll-free to
our control office: 1-800-645-4994.
To control combo units, like TV/VCRs or TV/DVDs, you must
This Warranty does not cover product purchased, serviced or used outside
program the individual corresponding device keys to control
the United States or Canada. This Warranty is not transferable and does
each part of the combo unit. Once programmed successfully, the
not extend to costs incurred for installation, removal or reinstallation of
TV key controls the TV functions, and the DVD/VCR key controls
the product. This Warranty does not apply if in the Company's opinion,
the VCR or DVD functions.
the product has been damaged through alteration, improper installation,
mishandling, misuse, neglect, accident, or the simultaneous use of different
Make sure the batteries are fresh and are properly installed.
battery types (e.g. alkaline, standard or rechargeable).
THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS
Problem: The remote doesn't perform commands properly.
LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO
Make sure the remote is in the correct mode by pressing the
EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE
corresponding device key (TV, SATELLITE/CABLE, DVD/VCR,
PAID BY PURCHASER FOR THE PRODUCT.
AUDIO/SOUNDBAR, STREAM1/AUX1, STREAM2/AUX2). This
This Warranty is in lieu of all other express warranties or liabilities. ANY
tells the remote which device to operate.
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL
Make sure device is ready (for example, the DVD player has a
BE LIMITED TO DURATION OF THIS WARRANTY. IN NO CASE SHALL
disc loaded).
THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL
You may have pressed an invalid key for the mode the remote is in.
DAMAGES WHATSOEVER. No person or representative is authorized
If you're trying to enter a channel number directly, try pressing
to assume for the Company any liability other than expressed herein in
connection with the sale of this product.
the ENTER key after entering the channel number as this is a
Some states/provinces do not allow limitations on how long an implied
requirement of certain models and brands.
warranty lasts or the exclusion or limitation of incidental or consequential
There is a possibility that a programmed code may only be
damage so the above limitations or exclusions may not apply to you. This
able to control some of your device features (for example, only
Warranty gives you specific legal rights and you may also have other rights,
turns a device on and off). To confirm that the device key is
which vary from state/province to state/province.
programmed with the correct code for maximum functionality,
test the device. Attempt to control a variety of the device's
functions with the remote. If some of the features of your
devices don't work, try programming the remote with a different
code in the list using the Direct Code Entry Method, until you
find the code that allows the remote to control the majority of
©2015 Voxx Accessories Corporation
your device's functions. Different codes can provide different
levels of functionality.
Trademark(s) ® Registered

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RCRPST06GR and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for RCA RCRPST06GR

  • Page 1 Make sure the batteries are fresh and are properly installed. GUIDE•HOME OPTIONS the remote to control. The INPUT — (dash) key Tip: This remote is already programmed to operate most RCA- keypresses that aren’t part of the search. CLEAR INFO AUDIO/SOUNDBAR, STREAM1/ for a different type of device, see the Changing a Key’s...
  • Page 2 “Cómo Probar el Código dispositivo (TV, SATELLITE/CABLE, • Mantenga el control remoto resguardado del polvo y la suciedad. de televisores, lectores de DVD y receptores de satélite RCA. dispositivo para un tipo de dispositivo diferente, consulte la Las teclas de flechas podría estar demasiado alejado del dispositivo o en un ángulo...

Table of Contents