Check-line TI-25P Operating Instructions Manual

Ultrasonic thickness gauge

Advertisement

Quick Links

N
OTES
- 20 -
T
ABLE OF
01.0
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
02.0
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
03.0
Operating Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
04.0
Condition and Preparation of Measuring Surface . . . . . . . . . . . . . . . . . .
05.0
Zeroing The Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0
6.0 Calibration Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
07.0
Transducer Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
008.0 Taking Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
09.0
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.0
Appendix A, Applications Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.0
Appendix B, Sound Velocity Of Common Materials . . . . . . . . . . . . . . .
12.0
Material Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.0
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT NOTE:
Inherent in ultrasonic thickness measurement is the possibility that the
instrument will use the second rather than the first echo from the back
surface of the material being measured. This may result in a thickness
reading that is TWICE what it should be. Responsibility for proper use of
the instrument and recognition of this phenomenon rests solely with the
user of the instrument.
- 1 -
C
ONTENTS
02
03
04
07
08
09
10
12
13
14
16
17
18

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TI-25P and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Check-line TI-25P

  • Page 1: Table Of Contents

    OTES ABLE OF ONTENTS 01.0 Introduction ..........02.0 Overview .
  • Page 2: Introduction

    NTRODUCTION OTES The TI-25P is a precision Ultrasonic Micrometer. Based on the same operating principles as SONAR, the TI-25P is capable of measuring the thickness of various materials with accuracy as high as ± 0.001 inches, or ± 0.01 millimeters.
  • Page 3: Overview

    2.2 Complete Kit The TI-25P is supplied as a ELECTROMACTIC Equipment Co., Inc. complete kit with the following: 600 Oakland Ave. Cedarhurst, NY 11516—USA a.
  • Page 4: Operating Elements

    Skin: Remove with water if desired. Eyes: Flush with water for 15 minutes. The PRB-0 key is used to “zero” the TI-25P in much the same way that Ingestion: For large quantities, induce vomiting and call a physician Inhalation: N/A a mechanical micrometer is zeroed.
  • Page 5: The Display

    Glass, flint 0.1680 4267 INMM/μs bars form the Stability Indicator. When Gold 0.1280 3251 the TI-25P is idle, only the left-most bar 0.1570 3988 1.8.8.8.8 and the underline will be on. When the Iron 0.2320 5898 gauge is making a measurement, six or Lead 0.8500...
  • Page 6: The Transducer

    TI-25P. The transducer must be used correctly in order for the TI-25P to produce accurate, reliable measurements. Below is a short description of the trans- ducer, followed by instructions for its use.
  • Page 7: Condition And Preparation Of Measuring Surface

    (refer to page 9) on a sample piece of known thickness, which is at or near the temperature of the material to be measured. This will allow the TI-25P to correctly calculate the velocity of sound through the hot material.
  • Page 8: Zeroing The Probe

    Sealed membrane, resistant to water and debris. petroleum products. 3. On the top of the TI-25P, above the display, is the metal probe-disc. Apply a Display Liquid-Crystal-Display, 4.5 digits, single droplet of ultrasonic couplant to the face of this disc.
  • Page 9: Programming The Sound Velocity

    In order for the transducer to do its job, there must be no air gaps between the In order for the TI-25P to make accurate measurements, it must be set to the cor- wear-face and the surface of the material being measured. This is accomplished rect sound-velocity for the material being measured.
  • Page 10: Transducer Selection

    TI-25P. Several factors affect the strength of ultrasound as it trav- Electromatic can provide assistance in choosing a transducer, and els.
  • Page 11 ® CHECK LINE • BY ELECTROMATIC TI-25P LTRASONIC HICKNESS AUGE Distributed by: ABQ Industrial LP USA Tel: +1 (281) 516-9292 / (888) 275-5772 eFax: +1 (866) 234-0451 Operating Instructions Web: https://www.abqindustrial.net E-mail: info@abqindustrial.net...

Table of Contents