Texts and values displayed on the device are marked by quotation marks and italics. Examples: ‘24ch’ , ‘OFF’ . 1.3 Symbols and signal words In this section you will find an overview of the meaning of symbols and signal words that are used in this manual. Xo8 LED Fx Strobe IP65 800W stroboscope...
Page 5
Warning signs Type of danger Warning – high-voltage. Warning – suspended load. Warning – danger zone. Xo8 LED Fx Strobe IP65 800W stroboscope...
There are no user-serviceable parts inside. Do not use the device if covers, protectors or optical components are missing or damaged. WARNING! Eye damage caused by high light intensity Never look directly into the light source. Xo8 LED Fx Strobe IP65 800W stroboscope...
Page 7
PVC floor and after some time cause permanent dark stains. In case of doubt, do not put the rubber feet directly on the floor, but use felt-pad floor protectors or a carpet. Xo8 LED Fx Strobe IP65 800W stroboscope...
UV rays). The seals and screw connections of the equipment must be checked regularly to ensure a fault-free operation. In cases of doubt, consult a specialist workshop in due time. Xo8 LED Fx Strobe IP65 800W stroboscope...
Possible data transmission errors For error-free operation make use of dedicated DMX cables and do not use ordinary microphone cables. Never connect the DMX input or output to audio devices such as mixers or amplifiers. Xo8 LED Fx Strobe IP65 800W stroboscope...
Page 10
Always work from a stable platform whenever installing, moving or servicing the unit. In doing so, the area underneath the unit must be cordoned off. 1 Quick lock openings for Omega brackets 2 Openings for safety cable Xo8 LED Fx Strobe IP65 800W stroboscope...
DMX input of the first slave device. Then connect the DMX output of the first slave device to the DMX input of the second slave device and so Please note that this device must not be connected to a dimmer. Xo8 LED Fx Strobe IP65 800W stroboscope...
Navigates upwards in a menu list. Increases the displayed value by one. [DOWN] Navigates downwards in a menu list. Decreases the displayed value by one. [ENTER] Selects an option of the respective operating mode, confirms the set value. Xo8 LED Fx Strobe IP65 800W stroboscope...
Page 13
Connections and controls Rear panel [DMX IN] DMX input (IP65 design) [DMX OUT] DMX output (IP65 design) [POWER OUT] Connection supply voltage outgoing (Power Twist IP65) [POWER IN] Connection supply voltage incoming (Power Twist IP65) Xo8 LED Fx Strobe IP65 800W stroboscope...
Connect the device to the power supply to start operation. After a few seconds, the display indicates that a reset is in progress. The device is then ready for use. The dis- play shows the operating mode that was selected when the unit was last powered off. Xo8 LED Fx Strobe IP65 800W stroboscope...
‘Auto’ ‘Strobe Program’ Stroboscope programme 0…5 No function 6…13 Stroboscope pro- gramme 1 14…21 Stroboscope pro- gramme 2 22…29 Stroboscope pro- gramme 3 30…37 Stroboscope pro- gramme 4 38…45 Stroboscope pro- gramme 5 Xo8 LED Fx Strobe IP65 800W stroboscope...
Page 16
0…255 ‘Program Speed’ 0…255 Running speed strobo- scope programme, increasing ‘Ground Dimmer’ 0…255 Brightness of coloured backlight (0 % to 100 %) ‘Ground Strobe’ 0…255 Strobe effect for the coloured backlight, increasing speed Xo8 LED Fx Strobe IP65 800W stroboscope...
Page 17
No automatic show 6…30 Automatic show 1 31…55 Automatic show 2 56…80 Automatic show 3 81…105 Automatic show 4 106…130 Automatic show 5 131…155 Automatic show 6 156…180 Automatic show 7 181…205 Automatic show 8 Xo8 LED Fx Strobe IP65 800W stroboscope...
Page 18
30 seconds, then the buttons are locked. To unlock the keys, press successively [ENTER], [UP], [DOWN], [UP], [DOWN] and then [ENTER] again. ‘System Info’ ‘Firmware’ ‘Software Version xxx’ Show firmware version of the device Xo8 LED Fx Strobe IP65 800W stroboscope...
Operating 7.3 Menu overview 7.4 Functions in 2-channel DMX mode Channel Value Function Strobe effect 0…10 Blackout 11…250 Strobe effect with increasing speed Colour macro for the backlight 0…5 Backlight off Xo8 LED Fx Strobe IP65 800W stroboscope...
Dimmer (0 % to 100 %) Stroboscope functions 0…5 Open strobe 6…10 Closed strobe 11…250 Strobe effect with increasing speed 251…255 Open strobe 0…255 Flash pulse duration, increasing Colour macro for the backlight 0…5 Backlight off 6…13 Xo8 LED Fx Strobe IP65 800W stroboscope...
Ramp-up effect with increasing speed 57…79 Random Ramp-down effect with increasing speed 80…102 Random strobe effect with increasing speed 103…127 Strobe-break effect with decreasing duration of interruptions 128…250 Strobe effect with increasing speed 251…255 Open strobe Xo8 LED Fx Strobe IP65 800W stroboscope...
Page 23
Colour macro for the backlight 0…5 Backlight off 6…13 14…21 Amber 22…29 Warm yellow 30…37 Yellow 38…45 Green 46…53 Turquoise 54…61 Cyan 62…69 Blue 70…77 Lavender 78…85 Mauve 86…93 Magenta 94…101 Pink 102…109 Warm white 110…117 White Xo8 LED Fx Strobe IP65 800W stroboscope...
Dimmer LED segment 1 (0 % to 100 %) 0…255 Dimmer LED segment 2 (0 % to 100 %) 0…255 Dimmer LED segment 3 (0 % to 100 %) 0…255 Dimmer LED segment 4 (0 % to 100 %) Xo8 LED Fx Strobe IP65 800W stroboscope...
Page 25
Colour macro for the backlight 0…5 Backlight off 6…13 14…21 Amber 22…29 Warm yellow 30…37 Yellow 38…45 Green 46…53 Turquoise 54…61 Cyan 62…69 Blue 70…77 Lavender 78…85 Mauve 86…93 Magenta 94…101 Pink 102…109 Warm white 110…117 White Xo8 LED Fx Strobe IP65 800W stroboscope...
Page 26
Intensity red (0 % to 100 %), background LED, segment 4 0…255 Intensity green (0 % to 100 %), background LED, segment 4 0…255 Intensity blue (0 % to 100 %), background LED, segment 4 Xo8 LED Fx Strobe IP65 800W stroboscope...
Operating supply voltage 100–240 V 50/60 Hz Protection class IP65 Temperature range –20 °C … +45 °C Dimensions (W × H × D) 585 mm × 285 mm × 220 mm Weight 15.2 kg Xo8 LED Fx Strobe IP65 800W stroboscope...
The unit offers a 3-pin XLR socket for DMX output and a 3-pin XLR plug for DMX input. Please refer to the drawing and table below for the pin assignment of a suit- able XLR plug. Configuration Ground, shielding Signal inverted (DMX–, ‘cold signal’) Signal (DMX+, ‘hot signal’) Xo8 LED Fx Strobe IP65 800W stroboscope...
DMX interface circuits. If the procedures recommended above do not succeed, please contact our Service Center. You can find the contact information at www.thomann.de. Xo8 LED Fx Strobe IP65 800W stroboscope...
Dispose of this device through an approved waste disposal firm or through your local waste facility. When discarding the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility. Xo8 LED Fx Strobe IP65 800W stroboscope...
Page 32
Notes Xo8 LED Fx Strobe IP65 800W stroboscope...
Page 33
Notes Xo8 LED Fx Strobe IP65 800W stroboscope...
Page 34
Notes Xo8 LED Fx Strobe IP65 800W stroboscope...