Advertisement
Set-up Device
Start Therapy
To access provider settings:
How to start
1. From the main menu, highlight Setup.
2. Press and hold ramp button and
control wheel simultaneously for 4-5
seconds until beep.
3. Provider Setup screen then appears.
To program device:
7XUQ FRQWURO ZKHHO WR VSHFLÀF VHWWLQJ
and press.
2. Turn control wheel to desired option
and press control wheel to select.
Stop Therapy
3. Turn control wheel to next setting
and repeat.
How to stop
4. To exit, turn control wheel to Back
and press.
View Information
In provider screen:
1. From the main menu, turn the control
1. Turn the control wheel to Info
wheel to Therapy and press.
and press.
2. The monitoring screen will be
2. Turn the control wheel to desired
displayed and the device will start.
option and press to view the
LQIRUPDWLRQ LGHQWLÀHG
Note: You can select the measured
3. To exit out of any option, turn the
parameter to display on the Monitor
Pressure screen. Choose from Leak,
control wheel to Back and press.
RR (Respiratory Rate), MinVent, or Vte
(Tidal Volume).
Comfort Settings
1. From the main menu, highlight
Comfort.
The Flex, Ramp Time, and Rise
Time comfort features will be shown
in this menu selection, if enabled.
7XUQ FRQWURO ZKHHO WR VSHFLÀF
1. Press and hold the control wheel for
setting and press.
2 seconds to turn the device off.
3. Turn control wheel to desired
option and press to select.
Note: You must be on the Main Menu
4. To exit, turn control wheel to
screen or in Therapy mode to turn
off the device.
Back and press.
Menus
Provider Setup Menu (cont.)
Provider Setup Menu
Therapy settings
Comfort settings
Mode
CPAP, S, S/T, T, PC
Flex Lock
CPAP
4-20
Flex
Rise Time Lock
AVAPS
Off (0), On (1)
(
not available on BiPAP S/T)
Rise Time
200-1500
Ramp Time
Tidal Volume
(
only when AVAPS is enabled)
Ramp Start Pressure
IPAP Max
4-30
+HDWHG 7XEH +XPLGLÀFDWLRQ
(only when AVAPS is enabled)
(only when using heated tube)
IPAP Min
4-30
Humidity Level
(only when AVAPS is enabled)
(only when using heated tube)
IPAP
4-30
Tube Temperature
EPAP
4 to IPAP
(only when using heated tube)
BPM
0-30
6\VWHP 2QH KXPLGLÀFDWLRQ
Inspiratory Time
0.5-3.0
+XPLGLÀHU
Tubing Type Lock
Tubing Type
System One Resistance Lock
System One Resistance (mask type)
Provider Setup Menu (cont.)
Alarm settings
Off (0), On (1)
Patient Disconnect Alarm
Off (0), 15 or 60 seconds
Off (0), 1, 2, 3
Apnea Alarm
Off (0), 10, 20 or 30 seconds
Off (0), On (1)
Low Minute Ventilation Alarm
Off (0), 1 to 99 lpm
1 (fastest) to 6 (slowest)
Off (0) to 45 minutes
Low Tidal Volume Alarm
Off (0), On (1)
4 to CPAP or EPAP setting
(only when AVAPS is enabled)
(depending on therapy mode)
System settings
Disable (0), Enable (1)
Backlight
Off, On
Language
Display language or Icon mode
1, 2, 3
hPa/cm H
O
hPa, cm H
2
Setup Parameter Display
1
Leak, RR, MinVent, Vte
Off (0), 1, 2, 3, 4, 5
Reset Blower Hours
Yes, No
Provider Mode
2
Off, On
Off (0) (classic mode),
Clear Patient Data
Yes, No
On (1) (System One humidity control)
Off (0), 1 (coolest) to 5 (warmest)
1. Setup Parameter Display
Off (0) (patient can adjust tubing size
You can select which measured parameters will display on the Monitor
diameter), On (1) (patient cannot
Pressure screen. Choose from Leak, RR (Respiratory Rate), MinVent,
adjust tubing size diameter)
or Vte (Tidal Volume). See the Measured Parameter section of the User
15 mm / 22 mm
Manual for more information.
Off (0) (patient can set mask type),
2. Provider Mode
On (1) (patient cannot set mask type)
You can choose "on" or "off" to enable or disable provider mode.
0, X1, X2, X3, X4, X5
Selecting "on" will put the device in provider mode (and the device will not
automatically return to user mode when the screen times out or you select
the Back option). Selecting "off" keeps the device in user mode.
O
2
Advertisement
