AMX NMX-MM-1000 Enzo Quick Start Manual

Overview
The NMX-MM-1000 Enzo Meeting Presentation System (FG3211-01) enables easy
access to content and documents stored on USB, on the web, or in the cloud. The Enzo
Media Presentation System is a power-efficient device with no moving parts that is
powered using Power over Ethernet (PoE).
To install the NMX-MM-1000, the following items are needed:
• 1 HDMI cable (Type A female)
• 1 PoE injector or PoE-capable Ethernet switch (802.3af compliant)
• 2 Cat5 cables
• 1 HDMI monitor
• USB keyboard and/or mouse
FIG. 1 NMX-MM-1000 (FRONT PANEL)
What's in the Box?
The Enzo Meeting Presentation System ships with the following items:
• 1 Enzo Meeting Presentation System
• 1 V-Style Single Module Surface Mount Kit
• Rubber feet
Specif ications
The following table lists the specifications for the NMX-MM-1000:
NMX-MM-1000 SPECIF ICATIONS
Power: • Power over Ethernet (PoE), 802.3af
• Maximum Power Consumption: 13W
Environmental: • Operating Temperature: 32° to 104° F (0° to 40° C)
• Storage Temperature: –4º to 158ºF (–20º to 70ºC)
• Operating Humidity: 5% to 85%, non-condensing
Dimensions: 1 3/8" (3.48cm) x 5 3/16" (14.73cm) x 3 5/16" (8.34cm) HWD
Weight: 1.1 lbs. (0.49kg)
Certifications: • RoHS
• FCC
• IC
• CE
Included • AVB-VSTYLE-SURFACE-MNT V-Style Single Module Surface
Accessories: Mount Kit (FG1010-722)
• Rubber feet
Optional • PS-POE-AF-TC, PoE Injector, 802.3af Compliant (FG423-83)
Accessories:
Mounting the NMX-MM-1000
The NMX-MM-1000 can be mounted using an AVB-VSTYLE-SURFACE-MNT V-Style
Single Module Surface Mount Kit (FG1010-722). The NMX-MM-1000 also has rubber
feet which can be applied to the bottom of the unit for table-top mounting.
Attaching Brackets
The Surface Mount Kit is designed for mounting a single module (to a wall, on or under
a desk, etc.) The kit contains brackets and screws. The brackets may be attached to
mount the top or the bottom flush with the mounting surface.
Insert the #4-40 3/16 inch pan head screws (provided) as shown in FIG. 2 and tighten.
Brackets can either align flush with the top or with the bottom.
FIG. 2 INSERT SCREWS AND TIGHTEN
NMX-MM-1000 Enzo™
• IEC 60950-1
• cULus 60950-1
• VCCI
• C-Tick
Mounting on a Surface
Note: The #8 x 1/2 inch tapping pan head screws provided for mounting to a flat surface
are designed for wood. If the module needs to be mounted on a different type of surface,
use the appropriate type of fastener, e.g., dry wall anchors (not provided).
1. Place the NMX-MM-1000 in the desired final position on the mounting surface
and mark the screw position as indicated in FIG. 3.
FIG. 3 MARK SCREW POSITIONS
Important: The mark for the screw's position in each of the mounting holes needs to be
made in the end of the slots (all marks to either the top of the slots or all marks to the
bottom).
2. Set the device aside. If using the wood screws provided, drill pilot holes (drill size
29; hole diameter 0.136 in.) for the screws 1/2 inch (1.27 cm) deep. Insert the
screws in the holes, but do not tighten them completely.
FIG. 4 DRILL PILOT HOLES AND INSERT SCREWS, DO NOT TIGHTEN
3. Align the module with the center of the double key-hole slots over the screws and
slide into place as indicated in FIG. 4.
4. Tighten the screws.
Installation
Installing the NMX-MM-1000 is a quick and simple process. Before connecting the
NMX-MM-1000 to its peripheral devices and powering the device, be sure to mount the
device using the desired method.
FIG. displays the connections for the NMX-MM-1000.
Cat5 cable from PoE injector to provide power
Connect peripheral devices
FIG. 5 NMX-MM-1000 (REAR PANEL)
Step 1: Connecting the NMX-MM-1000 to a Video Output
The NMX-MM-1000 uses standard HDMI cabling to connect to a video output. Connect
the HDMI OUT port on Enzo (FIG. 6) to a display monitor.
VIDEO OUTPUT CONNECTION
FIG. 6
Note: AMX recommends using ONLY 720p or 1080p displays to connect to Enzo.
QUICK START GUIDE
Meeting Presentation System
HDMI out to monitor