Table of Contents
Advertisement
Preface
Important Installation Information
It is the purchasers' responsibility to determine the suitability of this equipment and its derivatives for any given application. Any connection diagrams or usage information are
provided as examples only; each use will require independent evaluation. Advice regarding connections to/from 3
equipment manufacturer. When used with fire alarm systems the configuration and performance of the F-Link system should be confirmed with the fire alarm System Designer
and all other Interested Parties to establish that it complies with the system design and Fire Risk Assessment. Any references made to Standards / Codes of Practice are
provided for information only, and although believed to be correct at time of publication are subject to change.
Scope has, wherever possible, employed extra safeguards to monitor the system's performance. Certain system installations, operational requirements or budgets may,
however, limit the effectiveness of these safeguards. Again, the suitability of the system for any given application must therefore be decided by the installer and their customer,
relative to the application and risk. Good working practice dictates that a suitable system installation log must be generated, together with a record of the dates when the
system has been manually checked, (with the aid of signal strength meters etc.) enabling the system performance to be compared with the original installation data.
Installation must only be undertaken by a competent person (defined as a person with relevant and current training and experience, with access to the requisite tools,
equipment and information, and capable of carrying out the task), who shall ensure that all work is carried out in compliance with national wiring regulations and applicable
standards. This instruction manual is intended for use only by persons with a reasonable knowledge of electrical and electronic equipment, industry standard conventions and
terminology.
For UK equipment, Scope has no control of the use and application of the frequencies issued by OFCOM. Some equipment that is licensed may have greater protection than
other equipment which is operated on a WT Act License Exempt basis.
Important Safety Information
Scope products are designed to operate safely when installed and used according to general safety practices. The following requirements should be observed at all times:
This equipment is designed for indoor use, unless expressly stated otherwise, and must not be used in classified Hazardous Areas, including areas containing explosive or
flammable vapours, unless express authorisation has been given in writing by the manufacturer. If in doubt, consult your local product dealer for further information.
Do NOT subject this equipment to:
Do not obstruct any slots or openings in the product. These are provided for ventilation to ensure reliable operation of the product and to protect it from overheating. Only use
a damp cloth for cleaning (not liquid or aerosol based cleaners), and ensure that any power is removed from the unit prior to beginning the cleaning operation. Removal of
covers from the equipment must only be undertaken by authorised service personnel, who must ensure that power is isolated prior to removal.
Liability
Scope does not accept liability for any damage or injury, howsoever caused as the result of misuse of this equipment. It is the responsibility of the user to ensure that the
equipment is operated in the manner for which it was intended and that it is the correct item of equipment for the required task.
Warranty
This product is warranted as free from defects of workmanship and materials for a period of one year from the original purchase date. During this time, if there is a defect or
malfunction of this product, Scope will, with proof of purchase, repair or replace at its discretion any defective parts, free of charge. This does not include where the
adjustments, parts and repair are necessary due to circumstances beyond the control of Scope, including but not limited to fire or other casualty, accident, neglect, abuse,
abnormal use or battery leakage damage.
Hereby, the manufacturer Scope Communications UK Ltd declares that the radio equipment type: F-LINK4,
is in compliance with Radio Equipment Directive 2014/53/EU and ROHS Directive 2011/65/EU.
The full text of the EU Declaration of Conformity is available at the following internet address:
or from Scope at: Quantum House, Steamer Quay, Totnes, TQ9 5AL United Kingdom.
The supply of this equipment is governed by our standard terms and conditions of sale, which can be provided on request.
© Scope Communications UK Ltd, 2017 All Rights Reserved.
Ref: FLNK4red
F-Link Mk4 Supervised Transceiver System
Mechanical shock
Electrostatic discharge
Excessive humidity
www.scope-uk.com/technical/doc/DOCFLINK4.pdf
Page 2 of 23
rd
party equipment should always be sought from the
Moisture
Extremes of temperature
Corrosive liquids
Issue 1
Hide quick links:
Advertisement
Table of Contents
