Table of Contents
Advertisement
9. Commisioning and troubleshooting
When error message occur, please refer to chapter Function description see Operating elements/LED
diagnosis.
An acoustic message only occurs in the SHE main operating panel with the door closed or the door contact
switch pressed!
1)
The control panel is completely installed, without the operating voltage applied
a) Check all mechanical and electrical components for damage.
b) Check the DIP slide switches in the control panel for their correct (required) position.
c) Check all screw and plug connections for tightness and/or firm seating.
d) Check that all external components are installed.
Actuators:Is the final module at the last or only actuator inserted?
Automatic detectors: Is the active end module at the last or only detector inserted?
Manual detectors: Is the jumper only inserted in the last or only operating panel?
2)
With mains voltage, without accumulator
Adhere to the relevant regulations!
a) Connect the mains cables and reapply the mains voltage.
b) The mains LED is ON, the operating LED is OFF, the accumulator LED is ON. The malfunction
message at the operating panels is ON.
3)
With mains voltage, with accumulator
a) Remove the protection film of the lateral adhesive tape for the 1.9 Ah battery, and firmly press the
two batteries together according to the picture (next page).
b) Remove the protection film from one face of the supplied foam rubber. Glue each foam rubber to the
bottom side of the accumulators. Connect the accumulators to the black accumulator bridge
according to the wiring diagram, then connect the red and the blue connection cable to the red and
the black flat plug. Remove the bottom protection film of the foam rubber and insert the batteries in
the control panel according to figure 1, and firmly press down to the housing bottom!
c) Plug the red connection cable to the + and the blue connection to the flat plug of the control panel.
Note: Check correct polarity!
d) The operating LED is ON, the accumulator LED is OFF. The malfunction message at the operating
panels is OFF.
4)
Ventilation keypad
Closely observe the actuators during opening and closing. They must not be impaired in any position by
the building structure. Also the motor connection cables must not be subject to pulling or crushing.
a) Briefly actuate the Open button to have the actuators move open up to the final position. With the
SW2/2 =ON (hold-to-run) setting, the actuators only move as long as the button is pressed. The
OPEN display (if existing) in the button is ON.
b) Briefly actuate the CLOSED button, the actuators close. The Open display is OFF.
c) Press both buttons simultaneously while running, this corresponds to stop. The ventilation Open
display is ON, the actuators stop.
d) Briefly press the Closed button again, the actuators fully close, the Open display is OFF.
5)
Break glass unit, primary
a) Open the door and press the red Open button. The actuators move open through to the end position.
The red alarm LED (also in the control panel) is ON, at the same time a permanent acoustic signal
sounds (door contact pressed!).
For the WSC 204KP, where the break glass unit is located in the door, the break glass unit must be
exposed before the buttons can be pressed. To expose the break glass unit, the white plastic lever
arm on the backside of the door must be turned counter clockwise, hereafter the glass can gently be
pushed upwards and the break glass unit is exposed. When the glass is to be locked again, the lever
arm is turned clockwise. This is only necessary when the break glass unit in the door is the only
primary break glass unit and the signal cannot be deactivated from another primary break glass unit.
b) While running, press the Closed button at the ventilation button, then press both buttons, the
actuators must neither close nor stop!
c) Press the reset/Closed button in the operating panel. The actuators close through to the end position.
The ventilation function is released again. The red alarm LED (also in the control panel) and the
signal generator are OFF.
6)
Break glass unit, secondary
a) Check as described under 5). „Operation", „Malfunction" and the acoustic signal are missing!
18
Hide quick links:
Advertisement
Table of Contents
