Husqvarna LC247Li Operator's Manual page 13

LED lights
All LEDs are lit
LED 1, LED 2, LED 3 are
lit
LED 1, LED 2 are lit
LED 1 is lit
LED 1 flashes
To charge the battery
Charge the battery before the first use. The battery is
only 30% charged when supplied to the customer.
Note: The battery charger must be connected to the
voltage and frequency specified on the rating plate.
The battery does not charge if the battery temperature is
above 50°C. The battery charger decreases the
temperature of the battery before it starts to charge.
1. Connect one end of the power cord for the battery
charger into the socket of the battery charger.
2. Connect the other end of the power cord for the
battery charger in an grounded mains socket. The
LED on the battery charger flashes green one time.
(Fig. 30 )
3. Put the battery in the battery charger. The green light
on the charger comes on when the battery is
correctly connected to the battery charger.(Fig. 31 )
4. When all LEDs on the battery have come on the
battery is fully charged. Charge the battery for
maximum 24 hours.
5. To disconnect the battery charger from the mains
socket, pull the plug, not the power cord.
6. Remove the battery from the battery charger.
Battery charging status
A Husqvarna Li-ion battery can be charged or used at all
charging levels. The battery is not damaged. A fully
charged battery will not decrease its charge when the
battery is left in the charger.
LED display
LED 1 flashes
LED 1 is lit, LED 2 flashes 25%-50%
LED 1, LED 2 are lit, LED
3 flashes
LED 1, LED 2, LED 3 are
lit, LED 4 flashes
429 - 002 - 13.12.2017
Battery status
Fully charged (75-100%)
The battery is 50%-75%
charged
The battery is 25%-50%
charged
The battery is 0%-25%
charged.
The battery is empty.
Charge the battery.
Charging status
0%-25%
50%-75%
75%-100%
LED display
LED 1, LED 2, LED 3,
LED 4 are lit
To start the product
1. Put a charged battery in battery compartment
number 1 below the battery lid. For longer operation
time, put a second charged battery in battery
compartment number 2.
2. Turn the safety key to 1.(Fig. 32 )
3. Stay behind the product.
4. Press the ON/OFF button (A) on the control panel
and the green LED (B) comes on.(Fig. 33 ) When
you press the ON button, the two bars of the battery
indicator come on and show the levels of the two
batteries. After 2-3 seconds the battery indicator for
the battery not in operation goes off. The bar of the
battery in operation is shown for a longer time . (Fig.
34 )
5. Loosen the start inhibitor.(Fig. 35 )
6. Push the motor brake handle in the direction of the
handlebar.(Fig. 36 )
To use the drive on the wheels (LC
347VLi)
• Pull the drive bail in the direction of the handlebar to
start the drive.(Fig. 37 )
• Press + and - on the control panel to set the drive
speed in 4 steps.(Fig. 38 )
• Release the drive bail to disengage the drive, for
example when you go near an obstacle.
To use the SavE function
The product has a battery saving function (SavE) that
gives longer operation time.
1. Press the SavE button (A) to start the function. The
green LED comes on.(Fig. 39 )
2. Press the SavE button again to stop the function.
The green LED (B) goes out.
The SavE function stops automatically if the ground
conditions make it necessary to have a higher output.
The SavE function starts automatically when the ground
conditions let it.
High load function
When the product cuts long or wet grass, the motor
automatically increases rpm. The motor goes back to
standard mode when high load is not necessary.
To stop the product
The product stops automatically if you do not operate it
for 10 minutes. Always turn the safety key to 0 before
you let the product out of view.
Charging status
Fully charged
13