Related Manuals for Toshiba RAS-10PKVPG-E
Summary of Contents for Toshiba RAS-10PKVPG-E
-
Page 1: Installation Manual
INSTALLATION MANUAL ENGLISH AIR CONDITIONER (SPLIT TYPE) Indoor unit RAS-10PKVPG-E RAS-13PKVPG-E RAS-16PKVPG-E Outdoor unit RAS-10PAVPG-E RAS-13PAVPG-E RAS-16PAVPG-E 1 121451198... -
Page 2: Table Of Contents
CONTENTS PRECAUTIONS FOR SAFETY ............................1 ACCESSORY PARTS .................................5 INSTALLATION DIAGRAM OF INDOOR AND OUTDOOR UNITS ...................6 Optional Installation Parts ...............................6 INDOOR UNIT ..................................7 Installation Place ................................7 Cutting a Hole and Mounting Installation Plate .......................7 Piping and Drain Hose Installation ..........................8 Indoor Unit Fixing ................................9 In case of Indoor unit is fixed to Installation plate with screws ..................9 Drainage ..................................9... -
Page 3: Precautions For Safety
PRECAUTIONS FOR SAFETY Read the precautions in This appliance is filled with this manual carefully before R32. operating the unit. • Before installation, please read these precautions for safety carefully. • Be sure to follow the precautions provided here to avoid safety risks. The symbols and their meanings are shown below. - Page 4 DANGER • FOR USE BY QUALIFIED PERSONS ONLY. • TURN OFF MAIN POWER SUPPLY BEFORE ATTEMPTING ANY ELECTRICAL WORK. MAKE SURE ALL POWER SWITCHES ARE OFF. FAILURE TO DO SO MAY CAUSE ELECTRIC SHOCK. • CONNECT THE CONNECTING CABLE CORRECTLY. IF THE CONNECTING CABLE IS CONNECTED WRONGLY, ELECTRIC PARTS MAY BE DAMAGED.
- Page 5 • Do not use any refrigerant different from the one specified for complement or replacement. Otherwise, abnormally high pressure may be generated in the refrigeration cycle, which may result in a failure or explosion of the product or an injury to your body.
- Page 6 CAUTION • Exposure of unit to water or other moisture before installation could result in electric shock. Do not store it in a wet basement or expose to rain or water. • After unpacking the unit, examine it carefully for possible damage. •...
-
Page 7: Accessory Parts
ACCESSORY PARTS ACCESSORY AND INSTALLATION PARTS Parts name Parts name Wireless remote control* x 1 Installation plate* x 1 Battery x 2 Remote control holder* x 1 Mounting screw** ø4 x 25 Flat head wood screw ø3.1 x 16 Cap water proof*** x 2 (for some models only) Drain nipple*** x 1 (for heating model only) Owner’s Manual Installation Manual... -
Page 8: Installation Diagram Of Indoor And Outdoor Units
INSTALLATION DIAGRAM OF INDOOR AND OUTDOOR UNITS For the rear left and left piping Wall Insert the cushion between the indoor Hook Installation unit and wall, and tilt the indoor unit for plate better operation. The auxiliary piping can be connected to the left, rear left, rear right, right, bottom right or bottom left. -
Page 9: Indoor Unit
INDOOR UNIT Mounting the installation plate Installation Place Anchor bolt holes • A place which provides the spaces around the indoor unit as shown in the diagram Hook • A place where there are no obstacles near the air inlet and outlet •... -
Page 10: Piping And Drain Hose Installation
In case of bottom right or bottom left piping Piping and Drain Hose Installation • After scribing slits of the bush body with a knife or a making-off pin, cut them with a Piping and drain hose forming pair of nippers or an equivalent tool. * Since dewing results in a machine trouble, make sure to insulate both Slit connecting pipes. -
Page 11: Indoor Unit Fixing
Indoor Unit Fixing Drainage 1. Pass the pipe through the hole in the wall and hook the indoor unit on the 1. Run the drain hose sloped downwards. installation plate at the upper hook. NOTE 2. Swing the indoor unit to right and left to confirm that it is firmly hooked up on the installation plate. -
Page 12: Outdoor Unit
OUTDOOR UNIT Installation Place Refrigerant Piping Connection • A place which provides the spaces around the outdoor unit as shown in the diagram Flaring • A place which can bear the weight of the outdoor unit and does not allow an increase in noise level and vibration 1. -
Page 13: Evacuating
Tightening connection Compound pressure gauge Pressure gauge –101 kPa Align the centers of the connecting pipes and tighten the flare nut as far as (–76 cmHg) Manifold valve possible with your fingers. Then tighten the nut with a spanner and torque wrench as shown in the figure. -
Page 14: Electrical Works
ELECTRICAL WORKS The power supply can be selected to connect to indoor unit or outdoor unit. Choose proper way and connect the power supply and connecting cable by follow the instruction as following. Model RAS-10PKVPG-E RAS-13PKVPG-E RAS-16PKVPG-E Power source 50Hz, 220-240 V Single phase Maximum running current 8.50A... -
Page 15: Power Supply And Connecting Cable Connection
Power Supply and Connecting Cable Connection Power Supply Input at Indoor Unit Terminal Block (Recommend) Indoor Unit Outdoor Unit Power supply cable Stripping length of the power supply cable Terminal block Earth line 100 mm 10 mm Cord clamp 10 mm 90 mm Connecting Screw... -
Page 16: Power Supply Input Wiring Diagram
Power supply input Wiring Diagram Power supply input at Indoor unit Terminal Block (Recommend) Indoor Terminal Block Power supply input Outdoor EARTH Terminal Block CHASSIS Power supply input at Outdoor unit Terminal Block (Optional) Indoor Terminal Block Outdoor Terminal EARTH Block CHASSIS Power supply input... -
Page 17: Others
OTHERS Gas Leak Test Test Operation To switch to the TEST RUN (COOL) mode, press Temporary switch for 10 seconds. (The unit will make a short Pi sound.) Check places for the indoor unit. Temporary switch Check places for the outdoor unit. Auto Restart Setting •...