Advertisement
+01EN01BODY.fm Page 2 Thursday, June 27, 2013 4:35 PM
2
The remote controller
Remote controller (SX-U01EE)
1
8
9
2
10
3
11
4
12
5
6
13
7
18
14
19
15
20
16
17
21
Indicators
All icons on the display are shown for this explanation.
Icons related to heating do not appear for cooling only
models. Operations are not accepted when "SETTING" is
flashing.
1
Operation mode indicator
Indicates the operation mode selected.
2
Operation standby indicator
Indicates that the Super Modular Multi System
cannot cool if a different indoor unit is heating or
cannot heat if one is cooling; and that the Super
Heat Recovery Multi cannot heat or cool because
the outside temperature is outside the operating
range.
3
Remote controller sensor indicator
Displayed when the remote controller sensor is
used.
4
Setting indicator
Indicates that the model is being checked
automatically after a breaker is thrown or some
other occurrence.
5
Fan speed indicator
Indicates the selected fan speed:
"
Auto", "
High", "
Medium", " Low" or
"
Fix".
6
Test run indicator
Displayed during test run.
7
Louver position indicator
Indicates the louver position.
8
Pre-heat indicator
Displayed when the heating mode is energized or
defrost cycle is initiated.
While this indication is displayed, the indoor fan
stops or operate in fan mode.
9
Central control indicator
Displayed when the air conditioner is controlled
centrally and used with central control devices such
as the central remote controller.
If the use of the remote controller is prohibited by the
central control,
blinks when the ON/OFF,
MODE, or TEMP. button on the remote controller is
pushed, and the buttons do not function.
(Settings that can be configured on the remote
controller differ depending on the mode of the
central control. For details, read the Owner's
Manual of the central remote controller.)
10
Temperature setting indicator
The selected set temperature is displayed.
11
Service display
Displayed while the protective device works or a
check occurs.
12
Check code indicator
When a check occurs, alternately indicates the
indoor unit number and the check code.
13
Swing indicator
Displayed during up/down movement of the louver.
Operations
14
Set louver and swing button
Set automatic swing or the angle of the louvers.
15
Fan speed button
Selects the desired fan speed.
16
Test button
Used for test runs and for servicing.
*Not normally used.
17
Mode select button
Selects desired operation mode.
18
ON/OFF button
Turns on the unit when pushed, and turns off when
pushed again.
19
Temperature setting button
Adjusts the set temperature.
Select the desired set point by pushing temperature
button.
20
Operation lamp
Lights during operations. Blinks when a check
occurs or the protective device activates.
21
Remote controller sensor
Normally, the indoor unit's temperature sensor
detects the temperature, but it can also detect the
temperature near the remote controller. For details,
contact your dealer.
• Do not set during group control.
3
Correct usage
When you use the air conditioner for the first time or change the settings, follow the procedures below.
From next time, pushing the ON/OFF button starts running of the air conditioner with the chosen settings.
Cooling only models cannot do automatic operation (AUTO) and heating.
* See the Owner's Manual for the indoor unit regarding the operating limits of the functions for each button.
Standby
Operations are not accepted when "SETTING" is blinking.
REQUIREMENT
• Keep the power switch turned on during use.
• When you resume using the air conditioner after a long period of disuse, turn on the power switch at least 12 hours
before starting running.
Operations
1
5
4
3
2
1
ON/OFF button
Push the button to light the operation lamp and start
operations.
When heating
• The heated air comes out after a 3 to 5 minutes of
pre-heating with the indoor fan kept turned off.
2
Mode select button
Each time you push the button, the operation mode
and its icon change in the following order:
Auto
Heat
Dry
Cool
Fan
(Dehumidify)
(The indicator on the cooling only models does not
show: "
Auto" and "
Heat")
• For the multi-system, only Super Heat Recovery
Multi "
Auto" can be displayed and selected.
• With the Concealed Duct High Static Pressure
Type, "
Dry" is not available.
3
Fan speed button
Each time you push the button, fan speed and its
indication change in the following order:
Auto
High
Medium
Low
• "
Auto" cannot be selected in the Fan mode.
• It becomes "
Fix" for the Concealed Duct High
Static Pressure Type and other models that cannot
select the fan speed, so fan speed is fixed.
4
Temperature setting button
While the room temperature
is being shown,
push the temperature button to change LCD from
to
and select the desired set point.
The temperature setting range is 18.0 °C to 29.0 °C.
The temperature can be set in steps of 0.5 °C.
• LCD shows room temperature
5 seconds after
the temperature button was pushed.
• To change the set temperature, push the
temperature button again to change LCD to
and
select the desired set point.
• Contact your dealer for information on how to
switch the temperature indicator.
5
Set louver and swing button
• Refer to the Owner's Manual for the indoor unit
regarding the set louver and swing button, because
there is a slight difference depending on the model
of the indoor unit.
Advertisement
