Related Manuals for EuroLite LED Pixel Mesh
Summary of Contents for EuroLite LED Pixel Mesh
-
Page 1: User Manual
USER MANUAL LED Pixel Mesh © Copyright Keep this manual for future needs! Reproduction prohibited! -
Page 3: Table Of Contents
Features and Overview ………………………………...….……………….………….……….……….……………… Overall Requirements……….…………………….……………………….……………………….……………………..… Computer System Requirements……….……………………….……………………….………………………….…….. Set Up and Operation..............……..……………………………………………… LED Pixel Mesh Limitations ……………………………………………………………………….……...……….…….. Included with the Software Bundle………………………………………………………………………..………….. Communication Wire Facture…………………………………………………………………………………………. Making an additional Net-cable……………………………………………………………………………………… How to connect the Pixel Mesh……………………………………………………………………………………… .. IEC and Data Output Connections……………………………………………………………………………………... -
Page 4: Warning
WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP! SAFETY INSTRUCTIONS Every person involved with the installation, operation and maintenance of this dev ice has to: be qualified follow the instructions of this manual CAUTION! Be careful with your operations. -
Page 5: Operating Determinations
The user is responsible for correct positioning and operating of the LED Pixel Mesh. The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of this device. This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to earth. -
Page 6: Description
Description of the device Features The LED Pixel Mesh is a f abul ous LED Lightef fec t • Average Lifespan: 50,000~100,000hrs • Mounting system has rigging points and flexible configurations • Rated Power: 75W • Cooling: Direct air convection •... -
Page 7: Overall Requirements
• Windows XP computer with an available PCI slot • Graphics card with 2x DVI or 1x VGA + 1x DVI • LED Pixel Mesh Controll er; 1 controll er f or every 16 panel s w ide and 8 panel s high Computer System Requirements... -
Page 8: Included With The Software Bundle
Included with the Software Bundle User manual PC Sender Card DVI cable (DVI to DVI) Fig. 2 RS232 to RJ-11 cable CD with LED Studio 8... -
Page 9: Communication Wire Facture
Making an additional cable from the computer to the Scan Board A Standard NET CABLE cannot be used to replace the NET CABLE required to transmit the information for the LED Pixel Mesh. Please follow the following instructions in order to create extra NET CABLE. -
Page 10: How To Connect The Pixel Mesh
How to connect the Pixel Mesh Fig. 4 Note: Always make sure that all bolts are securely fastened. Do not use on systems larger than 5,12 meters in height ( 8 panels) -
Page 11: Iec And Data Output Connections
IEC and Data Output Connections AC Output AC Input 16 15 12 11 8 7 Data Input Data Output 14 13 Fig. 5... -
Page 12: Screen Control System Instruction
Screen Control System Instruction Sender card： • Make sure the PC is switched off. Take anti-static precautions, otherwise the entire PC can become damaged. • Install the sender card on the PCI slot of the PC; • Connect the DVI Port of the transmission card and DVI Display Port by DVI Cable; •... -
Page 13: System Connection Mode
System Connection Mode： • DVI Cable: connect the DVI Port between the PC and sender card (Fig. 7) • RS232 Serial Cable: connect the serial port between the PC and the sender card (Fig. 8). • SUPER CAT ISDN 8-Pin Cable: connect the sender card and receiving card with SUPER CAT ISDN 8- Pin Cable in order to achieve data transmission (Fig. -
Page 14: Mounting System To Led Screen Connection
Mounting System to LED Screen Connection Note: These bolts only need to be removed when a LED Panel needs to be moved or serviced. Each screen has to be fixed by its M6 holes on the side of each screen. There are 8 M6 holes in total. -
Page 16: Sender Card
Install the sender card in an available PCI slot in your computer. The sender card is the interface between your PC, LED Studio and the LED Pixel Mesh. You must use the DVI cable provided to connect from the computers DVI output to the DVI port on the sender card. -
Page 17: Backside View
Backside view Fig. 12... -
Page 18: Sender Card Installation
Sender card installation 1) Turn off your computer and disconnect from the powersource. Always take these precautions before opening the case and adding/removing components. 2) Insert the sender card into an available PCI slot in your computer. 3) Connect the DVI output from your computer’s display card to the DVI input on the sender card, Using the DVI signal cable provided. -
Page 19: Led Vision Studio Mx Control System Installation
LED Vision Studio MX Control System Installation • Put the LED Vision Studio MX CD in the PC and then enter the installation setup. If not, please double click the CD, choose LED Vision Studio MX Installation to start the installation. The Display shows LED Vision Studio MX (see Figure below). -
Page 20: Display Card Settings
Display Card Settings ATI Display Card Settings 1) Press the right MOUSE button, when standing on a blank desktop. Go to Properties, and set the screen resolution to 1024 x 768 pixels： 2) Press Advanced to set the refresh rate of the monitor to 60HZ：... - Page 21 3) Press the Display options and choose FPD, button will turn green: 4) Press cover options and choose copy mode options in the new popup screen to setup all the same:...
-
Page 22: Geforce Display Card Settings
GEFORCE Display Card Settings 1) Press the right MOUSE button, when standing on a blank desktop. Go to Properties, and set the screen resolution to 1024 x 768 pixels： 2) Press Advanced to set the refresh rate of the monitor to 60HZ：... - Page 23 3) Press the GeForce 7100 GS options, setting the nView. Choose the nView Display Settings menu, and press Clone： Choose Application and then Confirm. Now exit your Properties setup.
-
Page 24: Receiver Card Configuration
Receiver Card Configuration Configure the Recei v er Card after you have finished the LED Studio setup by installing main control card, receiving card, screen and connecting signal wire and power supply wire. Generally speaking, users do not need to configure the receiving card because the supplier has already set it before deliving the goods. - Page 25 3) Then type linsn on the keyboard and press enter. Note: there is no indication on the screen. After this a popup appears on the screen, requesting a password. You should enter the password in the popup. The password is“168”. Then press OK.
- Page 26 Receiver Setup The setup has already been perfected, so users do not need to do any work on the Receiver Setup. The configuration file is included with the LED Pixel Mesh: Pixel Mesh.RCG Users can refer to the following steps if they want to alter the configuration：...
-
Page 27: Maintenance
4. The electric power supply cables must not show any damages or material fatigue. The LED Pixel Mesh requires alm ost no m aintenanc e. How ever, you shoul d keep the unit c l ean. Otherwise, the fixture’s light-output will be significantly reduced.