Related Manuals for Agilent Technologies EXSLRSH110
Summary of Contents for Agilent Technologies EXSLRSH110
- Page 1 Vacuum Products Division SH-110 EXHAUST INSTRUCTION MANUAL SILENCER KIT Part No. 699904395 Rev. A April 2008...
-
Page 2: Sh-110 Exhaust Silencer Kit
SH-110 Exhaust Silencer Kit Copyright 2008 Agilent, Inc. -
Page 3: Warranty
SH-110 Exhaust Silencer Kit Warranty Products manufactured by Seller are warranted against defects in materials and workmanship for twelve (12) months from date of shipment thereof to Customer, and Seller’s liability under valid warranty claims is limited, at the option of Seller, to repair, replacement, or refund an equitable portion of the purchase price of the Product. - Page 4 SH-110 Exhaust Silencer Kit This page intentionally left blank.
-
Page 5: Documentation Conventions
SH-110 Exhaust Silencer Kit Preface Documentation Conventions This manual uses the following documentation conventions: Warnings indicate a particular procedure or practice, which WARNING if not followed correctly, could lead to serious injury. Cautions indicate a particular procedure or practice, which if CAUTION not followed, could cause damage to the equipment. - Page 6 SH-110 Exhaust Silencer Kit This page intentionally left blank.
- Page 7 Figure 1-3 shows the kit mounted at the exhaust of an SH-110 in the side position. Table 1-1 breaks down the kit parts and quantities. Table 1-1 Exhaust Silencer Kit for SH-110, P/N: EXSLRSH110 Part Name Filter/ Silencer Can NW 16 Clamp NW16 black 90°...
-
Page 8: Installation
SH-110 Exhaust Silencer Kit Installation To ensure proper operation, and to prevent damage, the kit NOTE must be installed and operated only as specified. To install: 1. Unscrew the ¼" NPT coupler for the pump's exhaust (unless using the small footprint version). - Page 9 SH-110 Exhaust Silencer Kit Do not use this kit If the application requires capture or WARNING containment of gases being pumped. Instead, route the pump exhaust to an appropriate collection system. Figure 1-2 shows the kit dimensions. Figure 1-2 : SH-110 Silencer/ Filter Can, Kit Dimensions Figure 1-3 SH-110 with Exhaust Silencer Kit Installed Figure 1-4 SH-110 with Exhaust Silencer Kit-small Footprint Version- No Resonator...
-
Page 10: Maintenance
SH-110 Exhaust Silencer Kit Performance Typical reductions are: 4 dB(A) measured at 1 m from the front of the pump, on a horizontal direction and an average of 3.8 db(A) from all three directions, under a 2-3 Torr load, and with the gas ballast open. - Page 11 Please follow these instructions whenever one of our products needs to be returned. 1) Complete the attached Request for Return form and send it to Agilent Technologies (see below), taking particular care to identify all products that have pumped or been exposed to any toxic or hazardous materials.
-
Page 12: Customer Information
This page intentionally left blank. 4) HEALTH and SAFETY CERTIFICATION AGILENT TECHNOLOGIES CANNOT ACCEPT ANY PRODUCTS CONTAMINATED WITH BIOLOGICAL OR EXPLOSIVE HAZARDS, RADIOACTIVE MATERIAL, OR MERCURY AT ITS FACILITY. Call Agilent Technologies to discuss alternatives if this requirement presents a problem. -
Page 13: Section 6) Additional Terms
Shipping Regulations (IATA, DOT, etc.) and carrier requirements. Customers receiving an Advance Exchange product agree to return the defective, rebuildable part to Agilent Technologies within 15 business days. Failure to do so, or returning a non-rebuildable part (crashed), will result in an invoice for the non-returned/non-rebuildable part. - Page 14 SH-110 Exhaust Silencer Kit This page intentionally left blank.
-
Page 16: Agilent Technologies
Agilent Technologies Vacuum Product Division United States & Canada India Southeast Asia Agilent Technologies Agilent Technologies Agilent Technologies Vacuum Products Division Vacuum Product Division Vacuum Products Division 121 Hartwell Avenue 205-A, “A” wing of Galleria, South East Asia (SEA) - Alex Ho...