WARNING Magnets are used in the lower headgear straps and the frame of the AirFit F20. Ensure the headgear and frame is kept at least 2" (50 mm) away from any active medical implant (eg, pacemaker or defibrillator) to avoid possible effects from localized magnetic fields.
GENERAL WARNINGS • The mask must be used under qualified supervision for users who are unable to remove the mask by themselves. The mask may not be suitable for those predisposed to aspiration. • The mask must be fitted with the supplied elbow (containing the valve and vent assembly) to ensure safe and functional usage unless otherwise specified.
• Remove all packaging before using the mask. Using your mask When using your mask with ResMed CPAP or bilevel devices that have mask setting options, refer to the Technical specifications section in this user guide for the correct setting.
Fitting 1. Twist and pull both magnetic clips away from the frame. 2. Ensure that the ResMed logo on the headgear is facing outwards and is upright. With both lower headgear straps released, hold the mask against your face and pull the headgear over your head.
1. Attach the cushion to the frame by aligning the circular openings and pushing together until retained. 2. With the ResMed logo on the headgear facing outside and upright, thread the upper headgear straps into the frame slots from the inside.
5. Leave the headgear to air dry out of direct sunlight. Reprocessing the mask between patients Reprocess this mask when using between patients. Cleaning, disinfection and sterilization instructions are available on www.resmed.com/downloads/masks. If you do not have internet access, please contact your ResMed representative.
Mask could be the wrong size. Talk to your clinician to have your face size checked against AirFit F20 fitting template. Note that sizing across different masks is not always the same. Mask is too noisy.
Technical specifications Pressure-flow curve The mask contains passive venting to protect against rebreathing. As a result of manufacturing variations, the vent flow rate may vary. Pressure Flow (cm H (L/min) Dead space Physical dead space is the empty volume of the mask to the end of the swivel.
Page 15
Radiation Protection (ICNIRP) Service life The service life of the AirFit F20 mask system is dependent on the intensity of usage, maintenance, and environmental conditions to which the mask is used or stored. As this mask system and its components are modular in nature, it is recommended that the...
Page 16
Mask setting options For AirSense, AirCurve or S9: Select 'Full Face'. For other devices: Select 'MIR FULL' (if available), otherwise select 'FULL FACE' as the mask option. Notes: • This product is not made with PVC or phthalates such as DEHP, DBP or BBP.
Page 17
Symbols The following symbols may appear on your product or packaging: Catalog number Batch code Humidity limitation Temperature limitation Not made with natural rubber Fragile, handle with care latex European Authorized Manufacturer Representative Keep away from rain This way up Full face mask Device setting - Full Face Size - small...
7 days. This warranty is only available to the initial consumer. It is not transferable. If the product fails under conditions of normal use, ResMed will repair or replace, at its option, the defective product or any of its components. This limited warranty does not cover: a) any damage caused as a result of improper use, abuse, modification or alteration of the product;...
Page 19
Mask components / Composants du masque / Piezas de la mascarilla / Componentes da máscara AirFit F20 AirFit F20 for Her Elbow / Coude / Codo / Cotovelo — — Valve (AAV) / Valve (VAA) / Válvula (AAV) / Válvula (VAA) Vent / Orifice de ventilation / Ventilación / Respiradouro...
Page 20
AirFit F20 AirFit F20 for Her A+B+C Frame system / Entourage complet / 63460 (S) 63463 (S) 63461 (M) 63464 (M) Sistema de armazón / Sistema de armação 63462 (L) A+B+C+D Complete system / Masque complet 63400 (S) 63403 (S)