Advertisement
1
2
NOTICE
The projector signal port and remote control
R out
R in
How to use the projector correctly:
1 Do not face to lens by eyes, it will hurt your eyes from
L out
L in
hard Light of the projector when it's working.
2 Do not block the air outlet, to avoid damage from
internal electronic device by projector can not cooling.
P C R G B
3 Do not use chemicals, Cleaner or water to clean, and also
1
avoid rain, moisture and leucocratic liquid to corrode
circuit board.
☆ Interface above for reference
only, different models are different,
4 Please put the projector and accessories on the place
please in kind prevail.
that children can not reach.
5 Please make sure the projector working environment is
dry and windy.
6 Do not place projector in too warm or too cold room, the high
temperature or low temperature will Shorten lifespan of the
device. The working environment would be 5℃~35℃ better.
Mute key: Open or close the volume.
7 Do not put the projector in heating equipment(drying machine,
Image effect reset:
microwave oven)to make it dry.
Can set the image brightness, soft
color or personality quickly inturn.
8 Do not press hard or put something heavy on the projector, it
Menu: Open or switch the parameter menu.
will damage projector.
9 Do not throw, beat, shake projector, it will damage circuit board
OK: Confirmation function.
in it.
Property: Display the file property under
Android mode.
10 Do not dismounting projector. Please contact after-sales service
if you have any problem.
11 Do not fix by yourself. If projector can not working normaly,
please consult with after-sales service or depot repair.
Numeric
3
Power
Y/Pb/Pr
Conponent video input
1：Plug the power cord into a power outlet.
Pr
Y
Video
AV input
2：Press the button"
Video
Pb
Lout/Rout
Audio output
H D M I 1
Lin/Rin
Audio input
PC-RGB IN
VGA input
H D M I 2
-
I N
HDMI1/2
HDMI Signal input
1/2
Multimedia interface
2
Network interface
Focus adjustment
1. Focal length setting: When the projector starts up, place it at the
position 1.9-3.5m from the projection screen, rotate the lens to
the left or right as illustrated in Fig.1 and Fig.2 to adjust the pict-
ure to the "clear" state to finish the focal length setting.
16:9, 4:3 switch key: Switch the display picture for 16:9 or 4:3.
Power key: For turning the power on.
H.Flip key: Adjust image left/ right rotate.
V.Flip key: Adjust image up/ down rotate,
not operational in USB mode.
Source: Select the source: AV, PC-RGB,
(1)
HDMI, etc.
Direction: Menu mode adjust parameter.
Keystone correction
1. Vertical keystone correction
Multimedia play:
① The vertical keystone correction
Function: play/ pause/ forward/ back.
is required when (1) and (3) be-
low appear during the first inst-
allation and use.
Back to previous operation.
（1）
（2）
（3）
② Dial the keystone button left and
right to adjust the picture to the
quadrangle as shown in (2) to fi-
nish the vertical keystone correc-
tion.
keystone button
4
Installation Method
The projector can be hung forwards on the ceiling with special ha-
nger frame and placed on the stable desk to project onto the scre-
"on the projector or on the remote control.
en forwards according to your operating environment and requir-
ements. In addition, the projector can be installed with other met-
R out
R in
Pr
Y
hods according to the following illustrations.
L out
L in
Video
Pb
H D M I 1
-
P C R G B
I N
H D M I 2
1
2
Screen
projector
Forward projection with
hanging frame
projector
projector
Screen
Forward projection on table
Attentions:
1) When the projector is installed in hoisting way, it shall not exceed the top
edge of the screen, if not, the image effect or the keystone correction will
(2)
be affected.
2) The projector shall be installed on the left-right symmetry axis of the
screen to avoid the keystone distortion of image to the left and right.
2. Horizontal keystone correction
3) The projector surroundings shall be well ventilated after the installation.
The air vents shall not be covered or blocked by any object.
4) The charged operation is not allowed during the installation to avoid the
electric shock hazard or the circuit fault of the projector.
5) When the newly installed projector is switched on for the first time, the top
and bottom margins of the image may show keystone distortion and blur.
①
②
③
Please adjust it according to debugging of the projector.
① If the picture is big in the left and small in
screen size
Projection distance(m)
the right, slightly swing the project to the
60"
right to correct the picture.
② Please refer to the picture. It is normal if
72"
the project is slightly oblique.
84"
③ If the picture is big in the right and small in
100"
the left, slightly swing the project to the
Remarks:
left to correct the picture.
As the optical parts have 3% optical error, the data in the table is for reference only.
R out
R in
Pr
Y
Please install the projector according to the screen size and actual measurements.
L out
L in
Video
Pb
H D M I 1
P C R G B
-
I N
H D M I 2
1
2
T V
5
Connect to the network
connect to WIFI
settings→ Wireless and networks →WiFi → WLAN，
choose the WIFI and enter the password,wait conne-
ction succeeded,you can access network.
Screen
projector
Backward projection with
hanging frame
Screen
Backward projection on table
Connect to the ethernet
Note:You should disconnect WIFI before connectting
to the ethernet.
1. Put cable in the RJ45 port directly,for dial up router.
2. Dial-up operation:
1.9~2.1
settings → Wireless and networks → Ethernet → PPPoE
2.3~2.6
settings,enter Username:Username;enter Password:cord
2.6~3.0
select Connect,wait,then you can access network.
3.1~3.5
6
Connect to the external
1:Use the proper cables for each connection.
The projector can connect various external
equipment,you should choose proper cables to
connect to the external equipment as needed.
2:Select corresponding signal source.
You can select the following icons from the left
side of the homepage.
AV
HDMI 1
HDMI 2
PC-RGB（computer VGA port）
YPBPR
NOTE：You can press"exit"on remote control to back to home
page when in external signal source condition.
Add:Different brand laptop output keys are as follows:
Lenovo
Fn+F3
Fujitsu
Fn+F10
Dell
Fn+F8
Haier
Fn+F3
HP
Fn+F4
NEC
Fn+F3
ThinkPad
Fn+F7
Panasonic Fn+F3
Asus
Fn+F8
Sharp
Fn+F5
Acer
Fn+F5
Hitachi
Fn+F7
Samsung
Fn+F4
TOSHIBA
Fn+F5
Sony
Fn+F7
The user of windows 7 or over win- dows7.Simply press
the
+P,select "copy"to connect.If the operation above
is invalid,Please update computer graphics driver.
Advertisement
