HDanywhere MHUB (8X6+2) Quick Start Manual

Q U I C K S T A R T G U I D E
6x MHUB RECEIVERS + 12x MOUNTING WINGS
The steps below describe how to connect a single HDMI source to a display location for outputs 1-6 and enable remote control (IR) signals to be sent from that location back
to your MHUB chassis. If you want to setup IR control on outputs 7 and 8, please refer to the product manual. Repeat the steps below as necessary for each source or display.
Connect a HDMI source device (e.g Satellite/Cable TV, Apple TV, Blu-ray,
1
DVD etc) to one of the ports labelled "SOURCE INPUT" on the MHUB
chassis using a good quality HDMI cable.
Connect a CAT cable between one of the HDBaseT output ports (labelled
2
A-F) on the MHUB chassis, and the "HDBASET" port on the MHUB receiver.
1
HDMI CABLE
CAT6 CABLE
INFRARED (IR) CABLE
NETWORK CABLE
POWER
CAT6 R ES O LUT I ON / D I STAN C E G UI D E
0m 10m
0ft 32ft
FU LL MANUA L O N SU P P ORT.HDAN YW HER E.CO M
I N T H E B O X
1 1
2 2
3 3
4 4
A b
5
5
6 6
7 7
8
8
1x MHUB 4K (8X6+2) CHASSIS
4
6
1 1 1 1 1
2 2 2 2 2
3 3 3 3 3
4 b 4 4 d 4 4
A 5 c 5 5 E 5
5
6 6 6 6 6
7 7 7 7 7
8 8 8 8 8
2
20m 30m
65ft 98ft
INFRARED (IR) CABLES 1x IEC POWER CABLE
1 1 1
2 2 2
3 3 3
4 4 4
c d E
5 5 5
6 6 6
7 7 7
8 8 8
Connect a HDMI cable between the port labelled "HDMI OUT" on the
3
MHUB receiver and a HDMI port on your display. Ensure that your display is
switched to the correct input. Note: MHUB receivers do not need any
power cables to work, power is delivered from the MHUB chassis. Check
the white LED light on the MHUB receiver is lit, this indicates a connection
with the MHUB chassis. Check that you are receiving a picture on the
connected display.
To control your HDMI source from your display location, connect an IR TX to
4
the "SOURCE IR (OUT)" port on the MHUB chassis, that matches the
"SOURCE INPUT" port number for the source you want to control. Connect
an IR RX to the "IR (IN)" port on the MHUB receiver.
Test the IR control is working by using the source device remote pointed
5
towards the IR receiver at your display location.
Connect the "HUB CONTROL IP" port to your router via an ethernet cable.
6
You can then download our uControl app which is available for iOS and
Android. The uControl App will also provide your MHUB IP address.
1 1 1
2 2 2
3 3 3
F 4 4 4
5 G 5 H 5
6 6 6
7 7 7
8 8 8
40m 50m
131ft 164ft
INPUTS
1 2 3
4 5 6
7 8
OUTPUTS
A B c
d
e f
g h
menu
ALL EDID
CLEAR OK
1x REMOTE CONTROL
1 1 1
2 2 2
3 3 3
4 4 4
F G H
5 5 5
6 6 6
7 7 7
8 8 8
3
60m
197ft
2x CHASSIS
MOUNTING BRACKETS
5
HD UHD
70m
230ft