Table of Contents
Advertisement
Quick Links
TURBO HD
Full Time Color Series
Turret Camera
User Manual
User Manual
Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.
This manual applies to the models below:
Model
DS-2CE72DFT-F
This manual may contain technical incorrect places or
printing errors, and the content is subject to change
without notice. The updates will be added to the new
version of this manual. We will readily improve or
update the products or procedures described in the
manual.
0100001080518
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-2CE72DFT-F
Summary of Contents for HIKVISION DS-2CE72DFT-F
-
Page 1: User Manual
This manual applies to the models below: Model DS-2CE72DFT-F This manual may contain technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual. - Page 2 Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
- Page 3 Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions”. Warnings: Serious injury or death may occur if any of the warnings are neglected.
-
Page 4: Product Features
Keep the camera away from liquid while in use for non-water-proof device. While in delivery, the camera shall be packed in its original packing, or packing of the same texture. Mark Description Table 0-1 Mark Description Mark Description DC Voltage 1 Introduction 1.1 Product Features... -
Page 5: Installation
2 Installation Before you start: Make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that all the related equipment is power-off during the installation. Check the specification of the products for the ... - Page 6 Expansion Bolts Self-tapping Screws Figure 2-2 Attach the Mounting Base to the Ceiling Note: The supplied screw package contains self-tapping screws, and expansion bolts. For cement wall/ceiling, expansion bolts are required to fix the camera. For wooden wall/ceiling, self-tapping screws are required.
- Page 7 Figure 2-5 Drill Template of the Junction Box Note: Drill the cable hole, when adopting the ceiling outlet to route the cable. 3. Take apart the junction box, and align the screw holes of the turret camera’s mounting base with those on junction box’s cover.
-
Page 8: Menu Description
3 Menu Description Purpose: Call the menu by clicking button on the PTZ Control interface, or call the preset No.95. Steps: 1. Connect the camera with the TVI DVR, and the monitor, shown as the figure 3-1. TVI DVR Camera Monitor Figure 3-1 Connection 2. -
Page 9: Exposure Mode
3.1 FORMAT You can set the video format as 2MP@25fps, or 2 MP@30fps. 3.2 EXPOSURE EXPOSURE describes the brightness-related parameters, which can be adjusted by EXPOSURE MODE, AGC, and SLOW SHUTTER. EXPOSURE GLOBAL EXPOSURE MODE MEDIUM SLOW SHUTTER BACK EXIT ... - Page 10 VIDEO SET TINGS WHITE BALANCE BRIGHTNESS CONTRAST SHARPNESS SATURATION 3 DNR MIRROR BACK EXIT SAVE & EXIT Figure 3-4 VIDEO SETTING WHITE BALANCE White balance, the white rendition function of the camera, is to adjust the color temperature according to the environment.
- Page 11 OFF: The mirror function is disabled. H: The image flips 180° horizontally. V: The image flips 180° vertically. HV: The image flips 180° both horizontally and vertically. 3.4 SMART LIGHT Under the SMART LIGHT sub-menu, you can set the mode as AUTO or OFF Figure 3-6 SMART LIGHT AUTO Under the AUTO mode, the white light turns on...
-
Page 12: Factory Default
be triggered. Up to 4 motion detection areas can be configured. Figure 3-8 MOTION Select a MOTION area. Set the MODE as ON. Click the up/down/left/right button to define the position, and the size of the area. Set the SENSITIVITY from 0 to 100. DPC (Defective Pixel Correction) Defective pixels are pixels in a CMOS image sensor, which fail to sense light levels correctly.