This manual applies to the models below: Model DS-2CE71D8T-PIRL This manual may contain technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual.
Page 2
Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Page 3
Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions”. Warnings: Serious injury or death may occur if any of the warnings are neglected.
Keep the camera away from liquid while in use for non-water-proof device. While in delivery, the camera shall be packed in its original packing, or packing of the same texture. Mark Description Table 0-1 Mark Description Mark Description DC Voltage 1 Introduction 1.1 Product Features...
2 Installation Before you start: Make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that all the related equipment is power-off during the installation. Check the specification of the products for the ...
Page 6
Expansion Bolts Fixing Screw Figure 2-2 Attach the Mounting Base to the Ceiling Note: The supplied screw package contains self-tapping screws, and expansion bolts. For cement wall/ceiling, expansion bolts are required to fix the camera. For wooden wall/ceiling, self-tapping screws are required.
Page 7
Figure 2-5 The Drill Template 3. Disassemble the inclined ceiling mount by the screw driver. 4. Install the turret camera’s mounting base on the inclined ceiling mount’s cover with three PM4 screws. Figure 2-6 Install Turret Camera’s Mounting Base 5. Install the inclined ceiling mount’s body on the ceiling/wall with four PA4 ×...
Page 8
You need to purchase a junction box separately. Steps: 1. Paste the drill template on the ceiling/wall. 2. Drill screw holes and the cable hole (optional) in the ceiling/wall according to the holes of the drill template. Figure 2-9 Drill Template of the Junction Box Note: Drill the cable hole, when adopting the ceiling outlet to route the cable.
Page 9
Figure 2-12 Fix the Camera to the Junction Box 2.1.4 Wall Mounting Before you start: You need to purchase a wall mount separately. Steps: Drill four screw holes in the wall according to the holes of the mount. 2. Install the mount to the wall by aligning the four screw holes of the bracket with expansion screws on the wall.
3 Menu Description Purpose: Call the menu by clicking button on the PTZ Control interface, or call the preset No.95. Steps: 1. Connect the camera with the TVI DVR, and the monitor, shown as the figure 3-1. Figure 3-1 Connection 2.
3.2 LANGUAGE Supports English, and Chinese. 3.3 WHITE LIGHT The embedded white light source can be worked as the visible alarm. In the WHITE LIGHT, you can set the mode as ALARM, or OFF. 3.3.1 ALARM In the ALARM mode, you can select the TRIGGER MODE as DVR, or CAMERA.
Page 12
The wide dynamic range helps the camera provide clear images even under backlight circumstances. WDR balances the brightness level of the whole image and provides clear images with details. AGC (Auto Gain Control) It optimizes the clarity of the image in poor light conditions.
Page 13
SMART IR The Smart IR function is used to adjust the light to its most suitable intensity, and prevent the image from over exposure. The SMART IR value can be adjusted from 1 to 8. The higher the value is, the more obvious effects are.
Select a PRIVACY area. Set the DISPLAY status as ON. Click up/down/left/down button to define the position, and the size of the area. MOTION In the user-defined motion detection surveillance area, the moving object can be detected and the alarm will be triggered.
Need help?
Do you have a question about the DS-2CE71D8T-PIRL and is the answer not in the manual?
Questions and answers