B.E.G. LUXOMAT PD2-M-DALI/DSI-SM Installation And Operating Instruction

LUXOMAT
Installation and Operating Instruction for B.E.G.-Occupancy detectors PD2-M-DALI/DSI-SM/-FC and PD4-M-DALI/DSI-SM/-FC
1a. Features
* For connection of up to 50 lamps
* Suitable for dimmable electronic
ballasts and control modules
* DALI/DSI output
* Constant light control
* Manual switching /dimming
* Semi or full automatic operation
* Luminance (brightness) set point,
switch-off delay time for LIGHT/HVAC
and orientation-light adjustable
* Sensor and power sections in one
housing
* Remote controllable
3a. Position DIP-Switches, LEDs and Potentiometer SM
Light
measurement
C
B
A
PD2-
Surface
mounting
DIP 1 = without function
DIP 2 = without function
DIP 3 = without function
4. Self test cycle
R2 20%
40
50 30
30 10
50
5
60
15
60
III II I
120
5
A
R2 20% R1
40
50 30
30 10 18 16
10
5
60
15 6
22
3
25
5
1
30
TE
R2
40
30
50
15
60
120 5
A
The product enters an initial
60-second self-test cycle, when
the supply is first connected.
The occupancy detector is
ready for operation. (red Led
flashes)
1b. Mounting preparations
Work on the 230 V mains supply
may only be carried out by quali-
fied professionals or by instructed
persons under the direction and
supervision of qualified skilled elec-
trical personnel in accordance with
electrotechnical regulations.
Disconnect supply before installing!
When in Master/Slave mode of
operation, the Master-appliance
must always be installed at the
location where there is least
daylight.
OFF ON
DIP
1 2 3 I II III
PD4-
Surface
mounting
Potentiometer A Lux Channel 1
Potentiometer B Time Channel 1
Potentiometer C Orientation lighting
5. Putting into operation / Settings
R1
LUX
Follow-up time for light control
2000
1200
The time can be set infinitely variably at between 1 and 30 minutes.
18 16 600
10
6 200
22
Symbol TEST: Test mode (Every movement switches on the light for a period
3
25
40
1
30
of 1 second, switching it off for a period of 2 seconds after that regardless
TE
of the level of brightness)
LUX
Twilight-switch for light control (relay 1)
2000
1200
The switch-on value for the light can be set at between 10 and 2000 Lux.
600
200
Using the rotary control, the luminance set points can be set as desired.
40
Symbol : Night-time operation | Symbol
Orientation lighting (fixed to 20%)
20% R1
2000
1200
The orientation lighting can be set infinitely variably at between 5 and 60
50 30 600
10 18 16
10
5
60 minutes resp. "ON" for permanent orientation lighting or "OFF" for no 6
22
3
25
orientation lighting. 1
30
TE
Pulse spacing PD-Slave
9s 2s
2 or 9 seconds can be set for the pause between 2 pulses sent to the
master. The setting can be made with activated (
LED indicator.
LED ON
LED OFF
For devices with a separate slave input, 2 sec. can be set.
PD2/PD4-M-DALI/DSI
®
2a. Installation of the LUXOMAT
PD4-M-DALI/DSI-
close open
The detector must be in stalled on a solid and level surface.
The circular cover ring must be removed prior to assembly.
To do this, twist the lens (C) of the PD4 or (D) of the PD2
anticlockwise through approximately 5° and lift off.
Having connected up the wires in accordance with regula-
tions, secure the detector with 2 screws. After installation
replace the lens and lock (turn clockwise). Mains to be
connected.
3b. Position DIP-Switches, LEDs and Potentiometer FC
I
C
Light
B
measurement
A
PD2-
False ceiling
mounting
LED I green Attention: The light sensor should be mounted
on the opposite side of the window.
LED II red
LED III white
: Daytime/Night-time operation
R2
LUX
40
50 30
60
60 15
120 5
200
A
40
) or deactivated ( )
R2 R2 20%
40 40
50 30
30 50 30 10
50
60
60
60 15 15
60
120 120 5
5
A
A
PD2/
®
SM
C
D
II III
A B C
3 1
2
The DIP switch settings are
remote control.
6. Settings carried out using remote control (optional)
1 2
20% R1 LUX
LUX
2000
2000
1200
1200
50 30 18 16 600
10 600
10
5
6 200
22 200
3
25 40
40
1
30
TE
1 2
20% R1 R1 LUX
LUX
2000
2000
1200 1200
50 30
18 16 600
10 18 16 600
10
10
5
5
6 200
22 6 200
22
3
3
25 25 40
40
1 1
30 30
TE TE
2b. Installation of the LUXOMAT
PD2/PD4-M-DALI/DSI-FC
68 mm
A circular opening of diameter 68 mm
must be produced in the ceiling. Having
connected up the cables in accor dance
with regulations, the detector is inserted
into the opening as shown in the drawing
opposite and fixed into position with the
assistance of the spring clips.
I II III
A B C
DIP
Light
measurement
OFF
PD4-
False ceiling
ON
mounting
using the
overriden
Remote control LUXOMAT IR-PD-DALI
®
1. Check Battery:
open battery compartment by pressing the
plastic springs together and removing the
battery-holder.
2. IMPORTANT
Please pay attention, that the setting is Potentio-
meter 1 at "TEST" and Potentiometer 2 not at
"SUN". All values which have been programmed
using the remote control will be deleted in the
event of power failure in the position "TEST /
SUN". Please switch Potentiometer 2 over to
"MOON" or any other value.
Caution:
Settings with remote control override the
potentiometer settings.
GB
®