ISTRUZIONI D’INSTALLAZIONe STRUZIONI ORIgINALI avatriCe ommerCiale IMPORTANT SAF XCAe2765FQ WARNING: To reduce the risk of re, electric shock, or i precautions, including the following: W10837716A www.whirlpoolcommerciallaundry.com Read all instructions before using the dryer. Keep a minimum clearance of 100 mm (4 in.) between the...
Transporting Your Washer ............5 Si vous avez besoin d’assistance ou service ...... 20 If You Need Assistance or Service ......... 5 POUR LE PERSONNEL D’ENTRETIEN AUTORISÉ FOR WHIRLPOOL AUTHORIZED SERVICE PERSON PAR WHIRLPOOL Tools & Parts ................6 Outillage et pièces ..............21 Alternate Parts &...
WASHER SAFETY NOTE: Washer installation and service must be performed by a Whirlpool authorized service person. IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow...
No washer can completey remove oil. Do not Do not install or store the washer where it will be dry anything that has ever had any type of oil exposed to the weather. on it (including cooking oils). Doing so can result Do not tamper with controls.
You will need the washer model number and serial number. Both numbers can be found on the serial-rating plate located LIMITED WARRANTY on the washer. IF YOU NEED SERVICE: Contact your authorized Whirlpool Commercial Laundry distributor. To locate your authorized Whirlpool Commercial Laundry distributor, ® ® visit www.WhirlpoolCommercialLaundry.com.
TOOLS & PARTS Tools Needed: Level Pliers Utility Knife 14 mm (9/16") Flat-Blade Screwdriver Open-End Wrench or Adjustable Wrench Optional tools: Flashlight Bucket Parts Supplied: Drain Hose with Clamp, Water Inlet Hoses (2) Inlet Hose Washers (4) U-Form, and Cable Tie ALTERNATE PARTS &...
DIMENSIONS Front View Side View 686 mm 686 mm (27") (27") 210 mm ") 921 mm 1.080 m ") ") 25 mm (1") 25 mm (1") Back View 406 mm (16") 267 mm ") 140 mm ") 1.130 m ") 946 mm ") 933 mm...
LOCATION REQUIREMENTS Selecting the proper location for your washer improves Recessed Area or Closet Installation performance and minimizes noise and possible washer “walk.” This washer may be installed in a recessed area or closet. Your washer can be installed in a basement, laundry room, The installation dimensions shown are the minimum spaces or recessed area.
INSTALLATION INSTRUCTIONS 2. To avoid damaging floor, place cardboard supports from shipping carton on floor behind washer. Tip washer back and place on cardboard supports. Remove shipping base. Set washer upright. IMPORTANT: Removing shipping base is necessary for proper operation. If your washer includes a sound shield, please refer to the instructions included with the sound shield to install it at this time.
LEVEL WASHER IMPORTANT: Level washer properly to reduce excess noise 2. Use a 14 mm or 9/16" open-end or adjustable wrench to turn and vibration. jam nuts clockwise on feet until they are about 13 mm (1/2") from the washer cabinet. Then turn the leveling foot clockwise to lower the washer or counterclockwise to raise the washer.
CONNECT DRAIN HOSE Proper routing of the drain hose avoids damage to your floor 5. Place hose into standpipe (shown in picture) or over side due to water leakage. of laundry tub. Remove drain hose from the washer basket IMPORTANT: D rain hose is not to exceed 203 mm (8") into drain pipe;...
DRAIN SYSTEM Floor drain system Drain system can be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Select method you need. Floor standpipe drain system 710 mm (28") 990 mm (39") 203 mm (8") Floor drain system requires a Siphon Break Kit (Part Number 285320).
CONNECT INLET HOSES Connect Inlet Hoses to Washer Insert new hose washers (supplied) into each end of the inlet hoses. Firmly seat the washers in the couplings. 1. Attach cold water hose to cold water inlet valve marked with NOTE: Use new hoses supplied with the washer. Do not reuse a blue ring.
ELECTRICAL REQUIREMENTS EARTHING INSTRUCTIONS This washer must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of electric shock by providing a path of least resistance for electric current. This washer is equipped with a cord having an equipment-earthing conductor and an earthing plug.
Earthing Connection For Free Vend, an OPL kit can be purchased from Whirlpool. Whirlpool part number W10222023. The available terminal is designed for a metal thickness of 1.51–1.91 mm.
WASHER DISPOSAL This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help avoid potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste.
DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance, you should ask your retailer about buying an extended warranty.