Do you have a question about the 1233 and is the answer not in the manual?
Questions and answers
Robert
April 9, 2025
Why die head produces good threads on 1233 machine then put on new machine and threads broke and flat
1 comments:
Mr. Anderson
April 10, 2025
The die head may break and flatten threads on the new machine due to several possible issues:
- The dies may be damaged, chipped, or worn out—replace them. - Incorrect or insufficient cutting oil—use only RIDGID® Thread Cutting Oil and ensure proper flow. - Die head may not be aligned properly—clean between the die head and carriage. - The pipe used may be of improper type or too thin—use black or galvanized steel pipe, schedule 40 or heavier. - Die head may not be set correctly—adjust for proper thread size. - Carriage may not be moving freely—clean and lubricate the rails. - Dies may be inserted in the wrong order—place them correctly in the die head. - Forcing the carriage feed handle during threading—do not force it once threading has started.
Any of these differences between the two machines could cause the new one to break or flatten threads.
Page 1
Hammer Wheel Chuck Scroll Jaw Insert Set Jaw Insert f/Coated Pipe Jaw Insert f/SS Pipe Chuck Jaw Set Chuck Cap Chip Guard Screws 6 - 32 x ″, Pkg of 6 ″ x 1 ″ Soc. Head Screw (6) 1233 999-998-716.10...
Page 2
Carriage Oil Line 47080 Oil Line Grommet 35117 Oil Line Insert 54152 Oil Intake Line 54142 Bulkhead Fitting 61897 Oil Filter Tube 58467 Filter Screen Assembly 45420 10-24 x ″ Screw 54517 Drip Pan Ridge Tool Company/Elyria, Ohio, U.S.A. 1233...
Page 3
52507 ″ NPT Close Nipple (2) 52512 ″ Coupling (2) 52517 Elbow Compression Fitting (2) 96830 Gear Case 96870 Gerotor Set Ridge Tool Company/Elyria, Ohio, U.S.A. 1233 3192R 3292R Ref. Catalog Description 96875 “O” Ring 96840 Cover Plate 96890 Screw #4 x ″...
Page 4
DO NOT order by Reference Number. Ref. Catalog Description 61902 Switch Mounting Screw 61907 Switch 54172 Switch Gasket 45420 10-24 x ″ Screw 44695 10-24 Nut 61912 Cord Clamp 92455 10-24 x ″ RH Screw 54232 Cord Grommet 46740 Power Cord 1233...
Page 5
36267 Pivot Pin 36272 Reamer Arm 52277 Reamer Cone 35355 Split Roll Pin Ridge Tool Company/Elyria, Ohio, U.S.A. 1233 NOTE: Order parts by Catalog Number only. DO NOT order by Reference Number. Ref. Catalog Description — 52452 763 Cutter Complete...
Page 8
Pipe and Bolt Threading Machine No. 100A Leg and Tray Stand No. 150A Wheel and Tray Stand No. 200A Wheel and Cabinet Stand Ridge Tool Company/Elyria, Ohio, U.S.A. 1233 NOTE: Order parts by Catalog Number only. DO NOT order by Reference Number. Ref. Catalog Description –...
Need help?
Do you have a question about the 1233 and is the answer not in the manual?
Questions and answers
Why die head produces good threads on 1233 machine then put on new machine and threads broke and flat
The die head may break and flatten threads on the new machine due to several possible issues:
- The dies may be damaged, chipped, or worn out—replace them.
- Incorrect or insufficient cutting oil—use only RIDGID® Thread Cutting Oil and ensure proper flow.
- Die head may not be aligned properly—clean between the die head and carriage.
- The pipe used may be of improper type or too thin—use black or galvanized steel pipe, schedule 40 or heavier.
- Die head may not be set correctly—adjust for proper thread size.
- Carriage may not be moving freely—clean and lubricate the rails.
- Dies may be inserted in the wrong order—place them correctly in the die head.
- Forcing the carriage feed handle during threading—do not force it once threading has started.
Any of these differences between the two machines could cause the new one to break or flatten threads.
This answer is automatically generated