Safety Instructions For Table Saw Safety is a combination of common sense, staying alert and knowing how your table saw works. Read this manual to understand this table saw. Safety Signal Words DANGER: means if the safety infor- mation is not followed someone will be seriously injured or killed.
Safety Instructions For Table Saw (continued) • Find and read all the warning labels found on the saw (shown below). When Installing Or Moving The Saw Reduce the Risk of Dangerous Environment. • Use the saw in a dry, indoor place protected from rain.
• If any part is missing, bent or broken in any way, or any electrical part does not work properly, turn the saw off and unplug the saw. • Replace damaged or missing parts before using the saw again. • Use the sawblade guard, spreader...
• Never cut more than one workpiece at a time. • Never turn your table saw “ON” before clearing everything except the workpiece and related support devices off the table.
Whenever Sawblade Is Spinning WARNING: Don't allow familiarity (gained from frequent use of your table saw) to cause a care- less mistake. Always remember that a careless fraction of a sec- ond is enough to cause a severe injury.
The pawls must stop a kickback once it has started. Replace or sharpen anti-kickback pawls when points become dull. (See “Maintaining Your Table Saw - Anti-Kickback Pawls” section.) • Plastic and composition (like hard- board) materials may be cut on your saw.
Glossary of Terms for Woodworking Anti-Kickback Pawls Device which, when properly maintained, is designed to stop the workpiece from being thrown towards the front of the saw at the operator during ripping operation. Arbor The shaft on which a cutting tool is mounted.
Page 10
Glossary of Terms for Woodworking (continued) Push Stick A device used to feed the workpiece through the saw during narrow ripping type operations which helps keep the operator’s hands well away from the blade. Push Block A device used for ripping type operations too narrow to allow use of a push stick.
Motor Specifications and Electrical Requirements Power Supply and Motor Specifications WARNING: To reduce the risk of electrical hazards, fire hazards or damage to the tool, use proper circuit protection. Your tool is wired at the factory for operation using the voltage shown. Con- nect tool to a power line with the appropriate voltage and a 15- amp branch circuit.
Motor Specifications and Electrical Requirements (continued) A temporary adapter may be used to con- nect this plug to a 2-prong outlet as shown if a properly grounded three prong outlet is not available. This temporary adapter should be used only until a prop- erly grounded three prong outlet can be installed by a qualified electrician.
Thermal Overload Protector This saw is equipped with a thermal over- load device which will automatically “trip” and cause the saw to shut down if the motor is overheating due to continuous heavy cutting or stalling. The overload device can only be reset manually by the user after the motor has been allowed to adequately cool.
WARNING: If any parts are miss- ing, do not attempt to use the table saw, plug in the power cord or turn the switch on until the missing parts are obtained and are installed correctly.
Getting to Know Your Table Saw Table Extension Lock Lever Rip Fence Sliding Table Miter Gauge Extension Table Rip Fence Front Fence Rail Storage MicroAdjust On-Off Rip Fence Switch MIter Gauge Thermal Storage Overload Device Elevation/Bevel Blade Tilt Handwheel Scale...
Page 16
Getting to Know Your Table Saw 1. Rip Fence...is locked in place by pushing the lock lever down until the lever rests on the stop. To move the fence, lift the lock lever and grasp the fence with one hand at the front.
Page 17
To turn saw OFF, PUSH lever in. Never leave the saw until the cutting tool has come to a complete stop. c. To lock switch in OFF position, hold switch IN with one hand, REMOVE key with other hand.
Page 18
Getting to Know Your Table Saw (continued) 17. Ind-I-Cut The plastic disk embedded in the table in front of the sawblade, is pro- vided for marking the location of the “sawcut” (kerf) on the workpiece. Check disk location: If it is above...
Blade Guard Storage Holds the blade guard when making non- thru cuts and transporting saw. Slide blade guard in as shown. Snap bottom edge of clear basket between latches on base. Wrench/Blade Storage Conveniently stores arbor wrenches as well as an extra sawblade. Secure wrenches and sawblade with blade stor- age washer and wing nut.
3/32 In., 5/32 In., 3/16 In. Remove Foam Motor Support A block of foam was placed under the motor at the factory for shipping. Lift up one edge of the saw base and remove the foam. Checking Table Insert WARNING: To reduce the risk of injury from accidental start, make sure switch is “OFF”...
Checking Heeling Adjustment or Parallelism of Sawblade to Miter Gauge Groove While cutting, the material must move in a straight line parallel to the sawblade. Therefore, both the miter gauge groove and the rip fence must be parallel to the sawblade.
Page 22
Alignment (continued) NOTE: Always review the section "Check- ing Blade Parallel to the Miter Gauge Groove" before proceeding with this sec- tion. 7. Loosen 1/2 turn the four alignment screws in the top of table next to the sawblade. This will allow the mecha- nism below the table to be shifted sideways.
3. Place the square against blade. Make sure square is not touching the tip of one of the saw teeth. A. If blade is square to table 1. Check pointer. If pointer does not point to the “0” mark on the bevel...
Page 24
2. Place an accurate square against blade. Make sure square is not touching the tip of one of the saw teeth. A. If blade is 45° to table; 1. Check pointer. If pointer does not point to the 45° mark on the scale, the scale must be adjusted.
Use these pages like a feeler gage to set the spacing between the bottom of the fence and the table top. 3. Rip fence should clear saw table sur- face just enough to allow eight pages to slide back and forth under rip fence. If...
Alignment (continued) Aligning Sliding Table Extension 1. Lock table extension lever. 2. Loosen the four nuts underneath the sliding table extension. 3. Use a combination square to make sure the top of the sliding table extension is the same height as the main table. 4.
To assure proper fence lock adjust- ment: a. Raise lock lever and push fence head toward rear of saw. b. Hold fence head down onto front guide bar while lifting rear of fence up and down. c. Tighten adjusting nut until fence clamp just barely touches rear guide bar.
2. Two (2) locator pins are on the blade guard. These locator pins fit into match- ing holes on a bracket located on the table saw trunnion. 3. Turn the blade guard locking knob clockwise to securely attach the blade guard in place.
7. Place rip fence on the right hand side of table. Carefully move it against blade so that it is parallel to the blade, and just touches tips of saw teeth. Tighten rip fence lock lever. 8. Insert folded paper between spreader and fence.
When installing the blade, make sure the teeth are pointing toward the front of the saw and that the blade and col- lars are clean, and free from any burrs. The hollow side of the collar must be against the blade.
Miter Gauge Alignment NOTE: The graduations are manufac- tured to very close tolerances which pro- vide ample accuracy for fine woodworking. In some cases where extreme accuracy is required, when mak- ing angle cuts, for example, make a trial cut and then recheck it. There are adjustable screw stops for the stop pin at 0°...
Alignment (continued) Marking the Ind-I-Cut: a. With blade 90° (square to table) and miter gauge in left groove, cross cut a piece of wood holding the wood firmly against miter gauge. b. Pull miter gauge back until freshly cut edge of wood is over disk. Using a sharp pencil, mark a line on disk at freshly cut edge of wood.
If table saw is to be used in a permanent location, it should be fastened securely to a firm supporting surface such as a work- bench, or legset using the mounting holes.
Workbench Mounting Using "C" Clamps An alternative method of securing your table saw is to fasten the saw base with "C" clamps. 1. Follow instructions for mounting to workbench, substitute "C" clamps at each mounting screw location.
• If any part is missing, bent or bro- ken in any way, or any electrical part does not work properly, turn the saw off and unplug the saw. To Reduce the Risk of Injury From Jams, Slips Or Thrown Pieces (Kickbacks Or Throwbacks) Inspect Your Blade.
• Tie back long hair. • Roll long sleeves above the elbow. • Noise levels vary widely. To reduce the risk of possible hearing dam- age, wear ear plugs or muffs when using table saw for hours at a time.
Plan the way you will push the workpiece through. • Never pull through. Start and finish the cut from the front of the table saw. • Never put your fingers or hands in the path of the sawblade or other cutting tool. Whenever Sawblade Is Spinning...
Many people custom build their own jigs and fixtures. Jigs and fixtures are often designed for a particular cut. You can use your table saw to easily make many jigs and fixtures. To get you started, we’ve included instructions for some simple ones.
2-1/2" from one end. Make a crosscut into the edge on the mark, stop- ping about 3/4" into the board. Set the saw and rip the width to 4-3/4" along the same edge as the stopped crosscut. Stop the ripcut where the two cuts intersect.
IMPORTANT: Make sure the screw heads do not stick out from the bottom of the base, they must be flush or recessed. The bottom must be flat and smooth enough to rest on the saw table without rocking. 3/4" Plywood Handle 3/8" Plywood Base Glue...
Fence Facing Select a piece of smooth straight wood approximately 3/4 inch thick, and the same length as the rip fence. Attach it to the fence with the three square head bolts, nuts and washers. (See “Hardware for Attaching Wood Facing”) in Repair Parts Figure 4.
Basic Saw Operations Using the Miter Gauge The miter gauge is used when crosscut- ting, miter cutting, bevel cutting, com- pound miter cutting, dadoing and when rabbeting across the end of a narrow workpiece. WARNING: For your own safety, always observe the following...
WARNING: To reduce the risk of kickback from twisting the work- piece, when clamping the block make sure that the end of the block is well in front of the saw- blade. Be sure it is clamped securely. Miter Gauge...
Basic Saw Operations (continued) Miter Crosscutting Miter cutting is cutting wood at an angle other than 90° with the edge of the wood. Follow the same procedure as you would for crosscutting. • Adjust the miter gauge to the desired angle, and lock it.
• When thru sawing, use an auxiliary fence and push block whenever the rip cut is between 1/2 and 2 inches from the blade. • Never thru saw rip cuts narrower than 1/2 inch. • Never rip anything shorter than 10” long.
Position the fence to the desired width of rip and lock in place. Before starting to rip, be sure: 1. Rip fence is parallel to sawblade. 2. Spreader is properly aligned with saw- blade. 3. Anti-kickback pawls are functioning properly.
(this may raise guard). WARNING: To reduce the risk of injury from blade contact never thru saw cuts narrower than 1/2" wide. Narrow strips thicker than the auxiliary fence/work support may enter the guard and strike the baffle. Carefully raise guard only enough to clear the workpiece.
Basic Saw Operations (continued) Using Featherboards for Thru Sawing Featherboards are not employed for thru sawing operations when using the miter gauge. Featherboards are used to keep the work in contact with the fence and table as shown, and to help stop kickbacks.
Using Featherboards for Non-Thru Sawing Featherboards are not employed during non-thru sawing operations when using the miter gauge. Use featherboards for all other non-thru sawing operations (when sawblade guard must be removed). Featherboards are used to keep the work in contact with the fence and table as shown and to stop kickbacks.
Depending on the thickness of the workpiece the width of the auxiliary fence/work support will have to be made so that it can be attached to the table saw top with “C” clamps. Clamp the auxiliary fence/work support to the table so that the...
The slot provided for the saw blade in the regular table insert is too small for the dado head to pass through. Therefore, a special dado insert must be purchased.
Basic Saw Operations (continued) Rabbeting Rabbeting is known as cutting out a sec- tion of the corner of a piece of material, across an end or along an edge. To make a rabbet requires cuts which do not go all the way through the material.
The molding head is assembled to the saw arbor in the same manner as the saw blade. It is not necessary to install the out- side loose collar before screwing on the arbor nut.
Maintaining Your Table Saw Maintenance WARNING: For your own safety, turn switch “OFF” and remove plug from power source outlet before maintaining or lubricating your saw. • Do not allow sawdust to accumulate inside the saw. Frequently blow out any dust that may accumulate inside the saw cabinet and the motor.
Troubleshooting WARNING: For your own protection, turn switch “OFF” and always remove plug from power source outlet before troubleshooting. General Trouble Probable Cause Excessive 1. Blade out of balance or Vibration damaged Cannot make 1. Miter gauge not square cut when adjusted properly.
Motor overheats 1. Motor overloaded 2. Improper cooling. (Air circula- tion restricted through motor due to sawdust, accumulating inside of saw.) Motor stalls 1. Voltage too low to permit (resulting in motor to reach operating blown fuses or speed.
Repair Parts Parts List for RIDGID 10 Inch Table Saw RIDGID parts are available on-line at www.ridgidparts.com Model No. TS24001 Figure 1 See Figure 5 See Figure 3 See Figure 4...
Page 59
Repair Parts Parts List for RIDGID 10 Inch Table Saw RIDGID parts are available on-line at www.ridgidparts.com Always Order by Part Number - not by Key Number Part No. Description 126317 * Bolt Carriage 1/4-20 x 1 827518 Mount Rail Extension...
Page 60
Repair Parts Parts list for RIDGID 10 Inch Table Saw Model No. TS24001 RIDGID parts are available on-line at www.ridgidparts.com Figure 2...
Page 61
Repair Parts Parts List for RIDGID 10 Inch Table Saw RIDGID parts are available on-line at www.ridgidparts.com Always Order by Part Number - not by Key Number Part No. Description 827483 Cover Blade 370625 * Screw Hex Wash Hd 1/4-20 x 1/2...
Page 62
Repair Parts Parts List for RIDGID 10 Inch Table Saw RIDGID parts are available on-line at www.ridgidparts.com Figure 3 - Miter Gauge Assembly Always Order by Part Number - Not by Key Number – 830338 826506-1 821063-5 826663 824723-1 123069-1...
Page 63
Repair Parts Parts List for RIDGID 10 Inch Table Saw RIDGID parts are available on-line at www.ridgidparts.com Always Order by Part Number - not by Key Number Part No. Description – 830421 Fence Complete 809492-5 Screw Pan Hd. Ty “T” 8-32x1...
Page 64
Repair Parts Parts List for RIDGID 10 Inch Table Saw RIDGID parts are available on-line at www.ridgidparts.com 16 17 Always Order by Part Number - not by Key Number Part No. Description – 827499 Guard Complete 62519 Spring, Pawl 827646...
Page 68
What is covered under the Limited Three Year Warranty This warranty covers all defects in workmanship or materials in this RIDGID® tool for the three year period from the date of purchase. This war- ranty is specific to this tool. Warranties for other RIDGID® products may vary.
Need help?
Do you have a question about the Table Saw and is the answer not in the manual?
Questions and answers