Advertisement
Quick Links
REAR SOLID DOOR TWO-POINT ELS1000/ELS1500 LOCK
Included Hardware:
ELS1000 Master Kit:
M4X12mm screw 1 ea.
M4 Washer, 1 ea.
M10 Washer, 1 ea.
M6 X 11mm Clevis Pin, 2 ea.
6 mm E-ring Ext., 2 ea.
ELS1000 latch box contains a set of standard fasteners, please select the items
shown below from the box:
M4X10mm Flanged Screw: 1 ea.
ELS1500 Master Kit:
M10 washer, 1 ea.
M5X16mm screw, 2 ea.
M6X35mm Hex screw, 1 ea.
M6 X 11mm Clevis Pin, 2 ea.
6 mm E-ring Ext., 2 ea.
Please select the spindle below from the ELS1500 latch box:
0.787" (20 mm)
Tools Required:
#2 Philips screw driver.
19 mm Wrench
Rivet gun
Installation Notes:
The cabinet door must be disassembled in order to install or remove a
•
two-point latch, because the lock rods extend beyond the top and
bottom of the door.
Installation Instructions
M16 Nut: 1 ea.
IIS-739227, 02/18/13, Rev. 1, CPI/
800-834-4969 (USA & Canada) • www.chatsworth.com • techsupport@chatsworth.com
For international phone numbers, see our website or contact CPI Tech Support.
This drawing contains proprietary and confidential information and is protected by U.S. and international law. Unauthorized reproduction, disclosure or use of the drawing
or the information therein is expressly forbidden except as agreed to in writing by Chatsworth Products, Inc.
ELS1000 Assembly Sequence
1. Install the two point ELS1000 (Fig. 1) onto rear solid door.
Rear plate
ELS1000
Front plate Border
ELS1000
ELS1000
Page 1 of 5
Lock rod
Clevis pin
Cam
M16 nut
M4 Washer
Fig. 1
ELS1000 Lock
E-ring
M4 X 10mm
screw
flanged
M10 Washer
M4 X 12mm
screw
Advertisement
Related Manuals for Chatsworth Products ELS1500
Summary of Contents for Chatsworth Products ELS1500
- Page 1 This drawing contains proprietary and confidential information and is protected by U.S. and international law. Unauthorized reproduction, disclosure or use of the drawing or the information therein is expressly forbidden except as agreed to in writing by Chatsworth Products, Inc.
- Page 2 Installation Instructions REAR SOLID DOOR TWO-POINT ELS1000/ELS1500 LOCK 2. Install lock rod guide brackets on top and bottom of rear door. Do not Lock rod Door back side insert the lock rods yet (Fig. 2). Guide Bracket 3. Position the ELS1000 lock with spindle orientation up and Front plate on the door over the latch cut-out and fasten with Rear plate using M4X12mm screws and M4 washer (Fig.
- Page 3 Installation Instructions REAR SOLID DOOR TWO-POINT ELS1000/ELS1500 LOCK 6. Insert the lock rods through the guides, with the short rod on the top Lock rod and the long rod on the bottom (Fig. 4). Guide 7. Insert the cam assembly pins through the short rod (on top) and the long rod (on bottom), then through the other half of the cam assembly (Fig.
- Page 4 Installation Instructions REAR SOLID DOOR TWO-POINT ELS1000/ELS1500 LOCK ELS1500 Assembly Sequence Lock rod Guide Bracket 1. Install the two point ELS1500 (Fig. 5) onto rear solid door. Lock rod Rear plate ELS1500 M6 X 35mm Hex screw Front plate Border...
- Page 5 Installation Instructions REAR SOLID DOOR TWO-POINT ELS1000/ELS1500 LOCK 5. Insert the cam assembly pins through the short rod (on top) and the Lock rod long rod (on bottom), then through the other half of the cam assembly Guide (Fig. 7) and locked with-ring.