Advertisement
Quick Links
TERAFRAME
Included Hardware:
ELS1000 Master kit:
M4X10mm Taptite screw 2 ea.
M4 Tooth Washer 2 ea.
M4 Washer, 1 ea.
M4 X 12mm screw 1 ea.
M6 X 11mm Clevis Pin, 2 ea.
6 mm E-ring Ext., 2 ea.
M10 Washer,1 ea.
ELS1000 latch box contains a set of standard fasteners, please select the items
below from the box:
M4 X 10mm Flanged Screw: 1 ea.
ELS1500 Master Kit:
M4X10mm Taptite screw 2 ea.
M4 Tooth Washer 2 ea.
M10 washer, 1 ea.
M5 X 16mm screw, 2 ea.
M6 X 35mm Hex screw, 1 ea.
M6 X 11mm Clevis Pin, 2 ea.
6 mm E-ring Ext., 2 ea.
M10 washer, 1ea.
Please select the spindle below from the ELS1500 latch box:
Tools Required:
#2 Philips screw driver
19 mm Wrench
10 mm wrench
Rivet gun
Installation Instructions
FRONT DOOR TWO-POINT ELS1000/ELS1500 LOCK
®
M16 Nut: 1 ea.
0.787" (20 mm)
IIS-739229, 11/27/13, Rev. 1, CPI/
800-834-4969 (USA & Canada) • www.chatsworth.com • techsupport@chatsworth.com
For international phone numbers, see our website or contact CPI Tech Support.
This drawing contains proprietary and confidential information and is protected by U.S. and international law. Unauthorized reproduction, disclosure or use of the drawing
or the information therein is expressly forbidden except as agreed to in writing by Chatsworth Products, Inc.
ELS1000/1500 Lock Preparation:
Locate the batteries from the lock box and install in the latch before assembly.
Please refer to the following Instruction documents for configuring the locks:
IIS-739226 (ELS1000), ISS-739228 (ELS1500).
Installation Notes:
The cabinet door must be disassembled in order to install or remove a
•
two-point latch, because the lock rods extend beyond the top and
bottom of the door.
ELS1000 Lock Assembly Sequence:
1. Install the two point ELS1000 (Fig. 1) onto TeraFrame front door.
M4 Tooth washer
Rear plate
ELS1000
Front plate 2
ELS1000
Front plate Border
ELS1000
ELS1000 lock
Page 1 of 6
M4 X 10mm
taptite screw
Lock rod
Clevis pin
Cam
M16 nut
M4 X 12mm
screw
M4 Washer
Fig. 1
ELS1000 Lock
E-ring
M4X10mm
Flanged screw
M10 Washer
Advertisement
Related Manuals for Chatsworth Products ELS1000
Summary of Contents for Chatsworth Products ELS1000
- Page 1 This drawing contains proprietary and confidential information and is protected by U.S. and international law. Unauthorized reproduction, disclosure or use of the drawing or the information therein is expressly forbidden except as agreed to in writing by Chatsworth Products, Inc.
- Page 2 3. Position the Rear plate inside the door over the latch cut-out and fasten 5. Secure the ELS1000 lock to the rear plate with the M4 X 12mm screws with two M4X10mm screws and M4 Tooth washer under each screw and M4 washer in the top and bottom holes (Fig.
- Page 3 7. Fasten the cam into the Lock spindle with M4X10mm flanged screws 9. Insert the cam assembly pins through the short rod (on top) and the and M10 washer in ELS1000 locks (Fig. 4). long rod (on bottom), then through the other half of the cam assembly (Fig.
- Page 4 Installation Instructions TERAFRAME FRONT DOOR TWO-POINT ELS1000/ELS1500 LOCK ® ELS1500 Lock Assembly Sequence: 2. Install lock rod guide brackets in the top and bottom door. Do not insert 1. Install the two point ELS1500 (Fig. 6) onto TeraFrame front door.
- Page 5 Installation Instructions TERAFRAME FRONT DOOR TWO-POINT ELS1000/ELS1500 LOCK ® 4. Place the ELS1500 lock with the Front plate border in front door with 6. Insert the cam into the Lock spindle and fasten with M6 X 35mm screws spindle orientation up and rear plate from other side of the door (Fig. 8).
- Page 6 Installation Instructions TERAFRAME FRONT DOOR TWO-POINT ELS1000/ELS1500 LOCK ® 7. Insert the lock rods through the guides, with the short rod on the top and the long rod on the bottom (Fig. 10). 8. Insert the cam assembly pins through the short rod (on top) and the long rod (on bottom), then through the other half of the cam assembly (Fig.