Advertisement
Quick Links
DOUBLE DOOR THREE-POINT ELS1000/ELS1500 LOCK
Included Hardware:
ELS1000 Master Kit:
M4 Washer, 1 ea.
M4X12mm screw 1 ea.
M10 Washer, 1 ea.
M6 X11mm Clevis Pin, 2 ea.
6 mm E-ring Ext., 2 ea.
ELS1000 latch box contains a set of standard fasteners, please select the items
below from the box:
M4X10mm Flanged Screw: 1 ea.
ELS1500 Master Kit:
M10 washer, 1 ea.
M5 X 16mm screw, 2 ea.
M6 X 35mm Hex screw, 1 ea.
M6 X 11mm Clevis Pin, 2 ea.
6 mm E-ring Ext., 2 ea.
Please select the spindle shown below from the ELS1500 latch box:
Tools Required:
#2 Phillips screw driver
19 mm Wrench
10 mm wrench
Installation Instructions
M16 Nut: 1 ea.
0.787" (20 mm)
IIS-739225, 11/22/13, Rev. 1, CPI/
800-834-4969 (USA & Canada) • www.chatsworth.com • techsupport@chatsworth.com
For international phone numbers, see our website or contact CPI Tech Support.
This drawing contains proprietary and confidential information and is protected by U.S. and international law. Unauthorized reproduction, disclosure or use of the drawing
or the information therein is expressly forbidden except as agreed to in writing by Chatsworth Products, Inc.
ELS1000/1500 Lock Preparation:
Locate the batteries from the lock box and install in the latch before assembly.
Please refer to the following Instruction documents for configuring the locks:
IIS-739226 (ELS1000), ISS-739228 (ELS1500).
Installation Notes:
The cabinet door must be disassembled in order to install or remove a
•
two-point latch, because the lock rods extend beyond the top and
bottom of the door.
ELS1000 Assembly Sequence:
1. Install the Three point ELS1000 (Fig. 1) onto double door.
Rear plate
ELS1000
Front plate Border
ELS1000
ELS1000
lock
Page 1 of 4
Clevis
E-ring
pin
M4 X 10mm
screw
M10 Washer
Cam
M16 nut
Lock rod
M4 X 12mm
screw
M4 Washer
Fig. 1
ELS1000 Lock
Advertisement
Related Manuals for Chatsworth Products ELS1000
Summary of Contents for Chatsworth Products ELS1000
- Page 1 This drawing contains proprietary and confidential information and is protected by U.S. and international law. Unauthorized reproduction, disclosure or use of the drawing or the information therein is expressly forbidden except as agreed to in writing by Chatsworth Products, Inc.
- Page 2 Installation Instructions DOUBLE DOOR THREE-POINT ELS1000/ELS1500 LOCK 2. Place the ELS1000 with the Front plate border on the double door with 5. Install the 3 point cam into the Lock Spindle with M4X10mm flanged spindle orientation up (Fig. 2) screw & M10 washer on ELS1000 spindle (Fig. 3).
- Page 3 2. Place the ELS1500 with the Front plate border on the double door with spindle orientation up (Fig. 5) 1. Install the Three point ELS1000 (Fig. 4) onto double door. 3. Position the Rear plate inside the double door over the latch cut-out and fasten to the lock with M5X16mm screw (Fig.
- Page 4 Installation Instructions DOUBLE DOOR THREE-POINT ELS1000/ELS1500 LOCK 4. Insert the lock rods through the guides, with the short rod at the top and the 5. Install the 3 point cam into the Lock Spindle with M6 X 35mm Hex screw &...