Chatsworth Products R.F. Mote Electronic Locking Swing Handle Installation

ations Specifications
ntents Package Contents
Electromechanical Data Rack Handle Lock with • 3525PRX Electromechanical Data Rack Handle Lock with
Reader Proximity Reader
unting Screws (qty 4) • M3x25 Mounting Screws (qty 4)
Electronic Locking Swing Handle - Installation
unting Screw (qty 1) • M3x14 Mounting Screw (qty 1)
miter (qty 1) • Rotation Limiter (qty 1)
qty 1) • Cam Bolt (qty 1)
ing Bracket (qty 1) • Top Mounting Bracket (qty 1)
unting Bracket (qty 1) • Bottom Mounting Bracket (qty 1)
Instructions (qty 1) • Installation Instructions (qty 1)
odule Actuator Module
12VDC to 24VDC (NOTE: Status LED will blink red if the Supply 12VDC to 24VDC (NOTE: Status LED will blink red if the
supply voltage is out of range.) Voltage supply voltage is out of range.)
Standby
50mA maximum at 12VDC 50mA maximum at 12VDC
Current
200mA maximum at 12VDC (with no external mechanical Operating 200mA maximum at 12VDC (with no external mechanical
load applied to handle) Current load applied to handle)
1A maximum at 12VDC (limited to 2 seconds) Stall Current 1A maximum at 12VDC (limited to 2 seconds)
1 second maximum (NOTE: Power must be present 1 second maximum (NOTE: Power must be present
during transit times. If power is removed while the lock Operating during transit times. If power is removed while the lock
slide is in transit, it will complete it's cycle when power Transit Time slide is in transit, it will complete it's cycle when power
RM
is restored.) is restored.)
RM
Electronic
3 seconds minimum 3 seconds minimum
RED - 12/24 VDC POSITIVE
RED - 12/24 VDC POSITIVE
Unlock Time
BLACK - 12/24 VDC NEGATIVE
BLACK - 12/24 VDC NEGATIVE
Open
WHITE - ACTIVATION TRIGGER
WHITE - ACTIVATION TRIGGER
Rated for supply voltage, maximum load Collector Rated for supply voltage, maximum load
YELLOW - 200 mA OUTPUT FOR ALARM
YELLOW - 200 mA OUTPUT FOR ALARM
Outputs BROWN - 200 mA OUTPUT FOR ALARM
BROWN - 200 mA OUTPUT FOR ALARM
ts 100mA/ output maximum Alarm Outputs 100mA/ output maximum
IS3525PRX
© 2015 RUTHERFORD CONTROLS INT'L | A DORMA GROUP COMPANY
1" *
WWW.RUTHERFORDCONTROLS.COM • PHONE: 1.800.265.6630 • FAX: 1.800.482.9795 • E-MAIL: SALES@RUTHERFORDCONTROLS.COM WWW.RUTHERFORDCONTROLS.COM • PHONE: 1.800.265.6630 • FAX: 1.800.482.9795 • E-MAIL: SALES@RUTHERFORDCONTROLS.COM
25mm
5.9" *
150mm
5.9" *
CAM Bolt
150mm
NOTE:
* 1) Cut-out dimensions.
2) Handing is determined by rotation
Bottom
Mounting Bracket
NOTE:
* 1) Cut-out dimensions.
2) Handing is determined by rotation
VIEWED FROM BACK VIEWED FROM BACK
limiter and bottom mounting bracket.
HANDLE ROTATION IS COUNTER CLOCKWISE HANDLE ROTATION IS COUNTER CLOCKWISE
FROM FRONT FROM FRONT
VIEWED FROM BACK VIEWED FROM BACK
HANDLE ROTATION IS COUNTER CLOCKWISE HANDLE ROTATION IS COUNTER CLOCKWISE
FROM FRONT FROM FRONT
Fig. 1
Package Contents:
Data Rack Handle Data Rack Handle
• Electromechanical Swing Handle with Proximity Reader
• M3 x 25mm Long Mounting Screws (qty 4)
• M3 x 14mm Long Mounting Screw (qty 1)
• Rotation Limiter
• Cam Bolt
Lock Plug
• Top Mounting Bracket
Proximity
• Bottom Mounting Bracket
Reader
• Installation Instructions
• Keys
Proximity Reader Module Proximity Reader Module
Voltage 12VDC to 24VDC Voltage
Operating Operating
20mA maximum
Current Current
Transmit Transmit
Handle
125kHz
Frequency Frequency
DATA Signal DATA Signal
5VDC
Voltage Voltage
DATA Pulse DATA Pulse
3525 Installation Instructions 40µs
Tri-Colour
Interval Time Interval Time
LED Indicator
DATA Signal DATA Signal
2ms
Delay Delay
3525PRX 3525PRX
Overall 8-1/4" H x 1-15/32" W x 2-1/8" D Overall
3525 Installation Instructions
Dimensions (210 x 37 x 54.3mm) Dimensions
Key Cylinder
© 2015 RUTHERFORD CONTROLS INT'L | A DORMA GROUP COMPANY
Fig. 1
Rotation Limiter
1" *
Fig. 1
1" *
25mm
25mm
CAM
Rotation Limiter
Top Mounting
CAM
Bracket Top Mounting
5.9" *
CAM Bolt
150mm
M3x14mm Screw
(1 place)
M3x14mm Screw
(1 place)
M3x25mm Screw
(4 places)
Bottom
Mounting Bracket
Mounting Bracket
NOTE:
M3x25mm Screw
* 1) Cut-out dimensions.
2) Handing is determined by rotation (4 places)
VIEWED FROM BACK
VIEWED FROM BACK VIEWED FROM BACK
limiter and bottom mounting bracket.
HANDLE ROTATION IS COUNTER CLOCKWISE
limiter and bottom mounting bracket.
HANDLE ROTATION IS COUNTER CLOCKWISE HANDLE ROTATION IS COUNTER CLOCKWISE
FROM FRONT
FROM FRONT FROM FRONT
Rotation Limiter
Viewed from back.
Rotation Limiter
Handle rotation is counter
clockwise from front.
Viewed from back.
VIEWED FROM BACK
HANDLE ROTATION IS CLOCKWISE
Handle rotation is anti-
FROM FRONT
VIEWED FROM BACK
VIEWED FROM BACK VIEWED FROM BACK
HANDLE ROTATION IS COUNTER CLOCKWISE
clockwise from front.
HANDLE ROTATION IS COUNTER CLOCKWISE HANDLE ROTATION IS COUNTER CLOCKWISE
FROM FRONT
FROM FRONT FROM FRONT
Rotation Limiter
Bottom Mounting Bracket
Viewed from back.
Bottom Mounting Bracket
Viewed from back.
Handle rotation is counter
Key rotation is counter
Viewed from back.
clockwise from front.
clockwise from front.
Key rotation is anti-clockwise
from front
VIEWED FROM BACK
HANDLE ROTATION IS CLOCKWISE
FROM FRONT
© 2015 RUTHERFORD CONTROLS INT'L | A DORMA GROUP COMPANY
Fig. 1
Tri-Color Status LED
-
+
Lock Plug
-
-
+
+
12VDC to 24VDC
20mA maximum
125kHz
5VDC
40µs
(Continued)
2ms
8-1/4" H x 1-15/32" W x 2-1/8" D
3525 Installation Instructions
(Continued)
(210 x 37 x 54.3mm)
Handle Mounting
1. Assemble handle according to the proper handing
Handle Mounting:
required.
Handle Mounting
1. Assemble handle according to the proper handing required.
Fig. 1
1. Assemble handle according to the proper handing
2. Rotation Limiter and Bottom Mounting bracket
2. Rotation Limiter and Bottom Mounting bracket determine handing.
required.
Rotation Limiter
determine handing.
2. Rotation Limiter and Bottom Mounting bracket
3. If existing cam or rod mechanism are installed on original handle
CAM
determine handing.
3.
If existing cam or rod mechanism are installed on
Top Mounting
remove and install on new handle.
3. If existing cam or rod mechanism are installed on
Bracket
original handle remove and install on new handle.
Bracket
original handle remove and install on new handle.
4. Ensure the proper cutout in the door
4. Ensure the proper cutout in the door. (See Fig. 1)
4. Ensure the proper cutout in the door. (See Fig. 1)
5. Install handle though cutout and install top & bottom mounting
5.
Install handle though cutout and install top & bottom
5. Install handle though cutout and install top & bottom
mounting brackets.
brackets.
mounting brackets.
6. Install wiring harness and route to hinge side of door
CAM Bolt
6. Install wiring harness and route to hinge side of door securing in
securing in place to ensure that nothing will bind or
6.
Install wiring harness and route to hinge side of door
catch. M3x14mm Screw
place to ensure that nothing will bind or catch.
securing in place to ensure that nothing will bind or
(1 place)
7. Proceed to wiring. (See Fig. 2)
catch.
7. Proceed to wiring
7. Proceed to wiring. (See Fig. 2)
M3x25mm Screw
Note:
(4 places)
Bottom
Handle rotation is determined by rotating
limiter and bottom mounting bracket
VIEWED FROM BACK
VIEWED FROM BACK
VIEWED FROM BACK VIEWED FROM BACK
HANDLE ROTATION IS COUNTER CLOCKWISE
HANDLE ROTATION IS CLOCKWISE
HANDLE ROTATION IS CLOCKWISE HANDLE ROTATION IS CLOCKWISE
FROM FRONT
FROM FRONT
FROM FRONT FROM FRONT
Rotation Limiter
Viewed from back.
Handle rotation is counter
clockwise from front.
VIEWED FROM BACK
HANDLE ROTATION IS CLOCKWISE
FROM FRONT
VIEWED FROM BACK
VIEWED FROM BACK
VIEWED FROM BACK VIEWED FROM BACK
HANDLE ROTATION IS COUNTER CLOCKWISE
HANDLE ROTATION IS CLOCKWISE
HANDLE ROTATION IS CLOCKWISE HANDLE ROTATION IS CLOCKWISE
FROM FRONT
FROM FRONT
FROM FRONT FROM FRONT
Bottom Mounting Bracket
Viewed from back.
Key rotation is counter
clockwise from front.
VIEWED FROM BACK
HANDLE ROTATION IS CLOCKWISE
© 2015 RUTHERFORD CONTROLS INT'L | A DORMA GROUP COMPANY
FROM FRONT
WWW.RUTHERFORDCONTROLS.COM • PHONE: 1.800.265.6630 • FAX: 1.800.482.9795 • E-MAIL: SALES@RUTHERFORDCONTROLS.COM
Specifications
Package Contents
• 3525PRX Electromechanical Data Rack Handle Lock with
Proximity Reader
• M3x25 Mounting Screws (qty 4)
• M3x14 Mounting Screw (qty 1)
Tri-Color Status LED
• Rotation Limiter (qty 1)
• Cam Bolt (qty 1)
• Top Mounting Bracket (qty 1)
• Bottom Mounting Bracket (qty 1)
• Installation Instructions (qty 1)
Actuator Module
Supply 12VDC to 24VDC (NOTE: Status LED will blink red if the
Voltage supply voltage is out of range.)
Standby
50mA maximum at 12VDC
Current
Operating 200mA maximum at 12VDC (with no external mechanical
Current load applied to handle)
Stall Current 1A maximum at 12VDC (limited to 2 seconds)
1 second maximum (NOTE: Power must be present
Operating during transit times. If power is removed while the lock
Transit Time slide is in transit, it will complete it's cycle when power
is restored.)
Electronic
3 seconds minimum
Unlock Time
Open
Collector Rated for supply voltage, maximum load
Outputs
(Continued)
Alarm Outputs 100mA/ output maximum
PCN15063 PCN15063
IS3525PRX
R11/15GR R11/15GR
Handle Mounting
1. Assemble handle according to the proper handing
required.
2. Rotation Limiter and Bottom Mounting bracket
determine handing.
3. If existing cam or rod mechanism are installed on
original handle remove and install on new handle.
(See Fig.1)
4. Ensure the proper cutout in the door. (See Fig. 1)
5. Install handle though cutout and install top & bottom
mounting brackets.
6. Install wiring harness and route to hinge side of door
securing in place to ensure that nothing will bind or
catch.
7. Proceed to wiring. (See Fig. 2)
.
(See Fig.2)
VIEWED FROM BACK
HANDLE ROTATION IS CLOCKWISE
FROM FRONT
Rotation Limiter
Rotation Limiter
Viewed from back.
Viewed from back.
Rotation Limiter
Handle rotation is
Handle rotation is
clockwise from front.
clockwise from front.
Viewed from back.
Handle rotation is
VIEWED FROM BACK
clockwise from front.
HANDLE ROTATION IS CLOCKWISE
FROM FRONT
Rotation Limiter
Bottom Mounting Bracket
Bottom Mounting Bracket
Bottom Mounting Bracket
Viewed from back.
Viewed from back.
Viewed from back.
Key rotation is clockwise
Handle rotation is
Key rotation is clockwise
Viewed from back.
from front.
from front.
clockwise from front.
Key rotation is clockwise from
front
2
1-905-884-5250
www.rfmote.com
info@rfmote.com
© 2015 RUTHERFORD CONTROLS INT'L | A DOR
WWW.RUTHERFORDCONTROLS.COM • PHONE: 1.800.265.6630 • FAX: 1.800.482.
.
v.160511 v.160511
2
Data Rack
Lock
VIEWED F
HANDLE
FROM FR
Proxim
Voltage
Operatin
Current
Transm
Frequen
DATA S
Voltage
DATA P
Interval
DATA S
Delay
3525P
Overall
Dimens
VIEWED FROM B
KEY ROTATION I
FROM FRONT