Samsung SR10M70 Series User Manual
Powerbot
Hide thumbs
Also See for SR10M70 Series:
- User manual (40 pages) ,
- Quick reference manual (16 pages) ,
- Quick reference manual (16 pages)
Related Manuals for Samsung SR10M70 Series
Summary of Contents for Samsung SR10M70 Series
- Page 1 POWERbot User manual SR10M70****, SR20M70**** Series • Before operating this unit, please read the instructions carefully. • For indoor use only. VR7000_EN_DJ68-00763D-09_SA.indd 1 2017-12-19 오후 4:17:27...
-
Page 2: Table Of Contents
Cleaning the dustbin / Cleaning the sensors and the camera / Cleaning the brush and Auto shutter tool / Cleaning the Driving wheel Samsung Connect App Notes and cautions Charging / Using / Cleaning and maintenance / About the battery / About the IrDA sensor... -
Page 3: Safety Information
Safety information SAFETY INFORMATION Before operating the appliance, please read this manual thoroughly and • retain it for your reference. WARNING Because these following operating instructions cover various models, the • characteristics of your vacuum cleaner may differ slightly from those WARNING described in this manual. - Page 4 Safety information IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should be observed, including the following: READ ALL INSTRUCTIONS BEFORE USING YOUR POWERbot. Unplug the battery charger / docking station from outlet when not in use and before conducting maintenance.
- Page 5 • Do not use extension cords or outlets with inadequate current carrying capacity. • Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord. • Do not mutilate or incinerate batteries as they will explode at high temperatures.
- Page 6 – There is a risk of fire or electric shock. gasoline, alcohol, thinners etc. f Please check with a Samsung Electronics f The POWERbot is intended for household service center when exchanging use therefore do not use it in an attic, batteries.
- Page 7 f When installing the docking station, do In use CAUTION not leave the cord carelessly on the floor since POWERbot may get tangled by it. f Using POWERbot on thick carpet may f Do not use POWERbot on black colored damage both POWERbot and the carpet.
-
Page 8: Installation
Installation The docking station must be plugged in and turned on at all times. Install the docking station in a place without obstacles and danger of falling. D C - I Connect the Connect the Connect the battery charger power cord power plug to jack to the to the battery... - Page 9 Accessories Remote control Batteries (AAA type) User manual Spare filter (Optional) (Optional) (Optional) Docking station Power cord Battery charger Boundary markers (Optional) ✻ ✻ Accessories may differ depending on the models. ✻ ✻ Refer to page 15 for the installation of boundary markers. ✻...
-
Page 10: Charging
Charging After completely charging the POWERbot for the first time (after purchase), it can be used for 60 min. in Nomal ( ) mode. (Refer to the page 39 for the charging time.) Smart Charging If POWERbot runs out of charge in Auto clean mode, it will automatically return to the docking station to be charged and will recommence the cleaning to complete the cleaning area after two- third of battery charging is done. -
Page 11: Battery (Lo
Automatic charging 1. SR10M701*** Series If the battery indicator blinks at 0.4 sec. intervals, the POWERbot will automatically return to the docking station to be charged. 2. SR10M70**** / SR2070**** Series When the battery indicator blinks during cleaning, the POWERbot will return to the docking station to charge itself automatically. -
Page 12: Using Powerbot
Using POWERbot You must turn on the emergency switch on the bottom of the unit before using POWERbot. Turning the power on/off Press the button for more than 3 seconds • When POWERbot is not used for 30 min.; SR10M70**U* / SR20M70**U* series: Turns to energy-saving mode. WARNING SR10M70**W* / SR20M70**W* series: Automatically returns to the docking station to be charged. - Page 13 Selecting cleaning modes Displayed icon SR10M702*** Cleaning mode How to select SR10M703*** SR10M701*** SR10M704*** SR20M70**** Auto clean Spot clean ✻ ✻ Press the [A,B type [C,D type ] on the remote Repeat clean controller first and then press the [Start/Stop ✻...
-
Page 14: Functions
Using POWERbot Cleaning method for each modes About 1.5 m Auto clean Spot clean Manual clean Repeat clean Automatically cleans the Cleans a localized area You can move Cleans repeatedly until set areas only once. intensely. It can be used POWERbot with the the battery is depleted. - Page 15 About the boundary markers To prevent the POWERbot from entering the following areas, attach the boundary markers on the floor in the shape at an interval of about 15 cm. About 15 cm About 15 cm About 5 cm Boundary Boundary markers markers where a raised spot is below 5 cm where there is a slide, swing, fireplace or any flammable substance or moisture.
-
Page 16: Using The Remote Control
Using the remote control [A Type] [B Type] 1, 2 1, 2 Refer to Refer to page 21 page 21 [C Type] [D Type] 1, 2 1, 2 Refer to Refer to page 22 page 22 ENGLISH-16 VR7000_EN_DJ68-00763D-09_SA.indd 16 2017-12-19 오후 4:17:43... -
Page 17: Cleaning Modes
[A Type] / [B Type] / [C Type] / [D Type] 1 Power / Recharging / Start/Stop Power Turn POWERbot's power on/off Select to recharge POWERbot at the docking Recharging station automatically Start/Stop Select to start or stop cleaning process 2 Cleaning modes Select to clean all set areas only once and Auto clean... - Page 18 Using the remote control 5 Manual clean mode & Direction control Move forward Select to move forward Turn left Select to turn left Turn right Select to turn right ✻ ✻ Moving backward is not available. 6 Point cleaning Available only with C, D type remote controllers. You can use the remote control to point and clean the desired spot while the POWERbot is in cleaning process.
-
Page 19: Name Of Each Part
Name of each part 1. Display panel 2. Remote control signal receiver 3. Obstacle sensor 4. Dustbin 5. Camera 6. Dustbin button 7. Bumper sensor 8. Auto shutter tool Bottom 1. Charge pins 2. Brush 3. Brush cover 4. Cliff sensor 5. - Page 20 Name of each part <SR10M702*** / SR10M703*** / SR10M704*** series> 1. Mute 2. Information Indicator 3. *Smart Control Off/On indicator 4. *Wi-Fi 5. Battery indicator 6. One-time/Daily schedule 7. Number display 8. Spot clean mode 9. Manual clean mode 10. Repeat clean mode 11.
-
Page 21: Setting Time/Schedule
Setting time/schedule [A Type, B Type] Only Auto clean mode can be scheduled. Setting the time You must set the current time before using the One-time/daily schedule. Start setting Select "Hour" Select "Minute" Setting complete Select "AM/PM" Skip to previous, next setting Setting the schedule Setting/cancelling the schedule can only be done while POWERbot is docked on the docking station. - Page 22 Setting time/schedule [C Type, D Type] Only Auto clean mode can be scheduled. Setting the time You must set the current time before using the One-time/daily schedule. Start setting Select "Hour" Select "Minute" Setting complete Select "AM/PM" Skip to previous, next setting Setting the schedule Setting/cancelling the schedule can only be done while POWERbot is docked on the docking station.
- Page 23 [SR10M701*** series] For the models which do not include a remote controller, schedule setting is available as below. Setting the schedule Setting/cancelling the schedule can only be done while POWERbot is docked on the docking station. When the schedule LED is turned Press for 3 sec.
-
Page 24: Cleaning And Maintaining
Cleaning and maintaining You must turn off the emergency switch before cleaning POWERbot. Cleaning the dustbin Press the button to Remove the dustbin Remove dust in the remove the dustbin cover dustbin and cyclone unit 'Click' Detach the cyclone Reassemble the Reinsert the dustbin unit from the dustbin dustbin... - Page 25 Cleaning the brush and Auto shutter tool Brush design may differ depending on the model. Remove the Remove the Clean the Clean the auto brush cover brush brush shutter tool Reassemble the brush Reassemble the brush cover Cleaning the Driving wheel Put a soft cloth on the floor and place Use a blunt rod or tweezers to remove POWERbot upside-down on the cloth.
-
Page 26: Samsung Connect App
Samsung Connect App The Samsung Connect App is only compatible with models that have a Wi-Fi function. Setting up the wireless router f Please refer to the user manual of your wireless router if you have access problems. f Samsung POWERbot supports only Wi-Fi 2.4 Ghz. - Page 27 – [iOS 10.0] or later / iPhone 6 or later is supported. f Visit Play Store or App Store to see if your mobile device is compatible with Samsung Connect.
- Page 28 4. [Android] The connection to your device will be progressed automatically. – [iOS] Open the setting app, and select [Robot vacuum] Samsung in the Wi-Fi list. 5. Provide the authentication when you are directed to do so.
- Page 29 Please wait for completing the update before using the POWERbot. Using the Samsung Connect APP f When you tap the device card on the Samsung Connect app, the plug-in for your device will be launched. 1. Power (on / off) 2.
-
Page 30: Notes And Cautions
The POWERbot cannot completely clean areas it cannot enter, such as corners, from the brush, contact an authorized between the wall and sofa, etc. Samsung service center. – Please use another cleaning tool to clean them regularly. ENGLISH-30 VR7000_EN_DJ68-00763D-09_SA.indd 30... - Page 31 Note f Different infrared signals may interfere f Purchase batteries at authorized with one another and cause the devices Samsung centers and check for the to malfunction if they are used together symbol ( ) which is stuck on the in a small space or in close proximity.
-
Page 32: Information Codes
Information codes <SR10M701*** series> The three Turn off the Information code indicators below emergency switch will disappear blink and an and check the when you turn on information below instructions the emergency codes alarm and take switch sounds. appropriate action Information codes animation Information codes Information codes... -
Page 33: Emergency Switch
<SR10M702***, SR10M703***, SR10M704***, SR20M70**** series> The information Turn off the Information code code below is emergency switch will disappear shown with an and check the when you turn on error alarm. below instructions the emergency and take switch appropriate action Information codes Checklist The POWERbot is caught, stuck or trapped while... -
Page 34: Troubleshooting
Troubleshooting Symptom Checklist fCheck if the emergency switch is on. fCheck if all the icons are displayed on the display panel. fCheck if the POWERbot's battery is depleted. – When "Lo" is displayed, place the POWERbot on the docking The POWERbot is not station to charge it. - Page 35 Or turn off the power supply of the POWERbot, phone is normally connected turn it on, wait for a minute or longer, and then run the Samsung to the POWERbot. Connect app again.
- Page 36 POWERbot and Smartphone, run the Samsung Connect App again and try the product registration. fThe same Samsung account should be used for the login of App and product registration. fAll users should use the Samsung account issued by the same country.
- Page 37 POWERbot is distant from a wireless router, connection cut may occur. A connection cut between fReset the POWERbot and the smart phone, and check the the Samsung Connect connection again. App and the POWERbot suddenly occurs during fIf the connection cut occurs repeatedly, try the product registration normal operation of the again.
-
Page 38: Open Source Announcement
It is also possible to obtain the complete corresponding source code in a physical medium such as a CD-ROM; a minimal charge will be required. The following URL http://opensource.samsung.com/opensource/VR7000_A20_TZ/seq/0 leads to the download page of the source code made available and open source license information as related to this product. -
Page 39: Specifications
Specifications <SR10M70**** series> Detail information SR10M702*** Classification Item SR10M701*** SR10M703*** SR10M704*** Size (D x H x L) 340 mm x 97 mm x 348 mm Weight 4 kg Mechanical specifications Ceiling shape recognition (Visionary mapping Sensor (POWERbot) plus TM) Button type of POWERbot Touch type Power voltage 100-240 V ~ , 50 Hz/60 Hz... - Page 40 If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. Country Customer Care Center Web Site AUSTRALIA 1300 362 603 www.samsung.com/au/support www.samsung.com/hk/support (Chinese) HONG KONG 3698 4698 www.samsung.com/hk_en/support (English) 1800-88-9999 MALAYSIA 603-77137477 (Overseas www.samsung.com/my/support...