Anviz D100 Operation Manual

D100/D200
Product Appearance
5
1. LCD
1
6
2.State Key(Clock Out)
Page Down
2
7
3.State Key(Clock In)
Fingerprint Employee Time Clock
3
Page Up
8
4.0-9 Num. Key
9
4
5.LED
10
1
2
Fingerprint Employee Time Clock
3
4
Illustration for placing finger
Correct method
(Place you finger flat on the sensor to insure maximum sensor coverage )
Place finger in the center of the sensor. Finger must remain flat and motionless
during enrollment and verification.
Incorrect method:
Moving finger before the Improper finger placement Finger placed on Removing finger from the sensor
backlight of sensor is off. on the sensor. sensor at an angle. during enrollment or verification process.
Operation Guide
Enroll User:
Each user can register two fingerprints and one password .
IN MENU User
▼
09 : 00 User Enroll
[M] [OK]
26
Setup Delete
10-11-17 WED System Info Verify Mode
Select [User] Select [Enroll]
Enroll Fingerprint:
Place the same finger on the sensor twice to enroll fingerprints.
Enroll Enroll FP Enroll FP
FP 1/2
[OK] [OK]
Password Place Finger #1 Place Finger #2
Esc-C Set-OK
Select [FP] Enroll fingerprint
Enroll Password:
Password length: 0-999999.
Enroll Enroll PWD Enroll PWD
FP 1/2
[OK] [OK] [OK] PWD ID
Password PWD ID
******
Confm
Esc-C Set-OK Esc-C Set-OK
Select [Password] Input password Input password again
Admin Setup:
Admin(Administrator) has full access permissions to the device. It is recommended to assign a minimum of two administrators to each unit.
IN
MENU User ▼
09 : 00 User Admin Setup
[M] [OK]
26
Setup Admin Clear
10-11-17 WED System Info
Select [User] Selelct [Admin Setup]
Desktop Series Fingerprint Employee Time Clock Operation Guide
Menu List
Press [OK] key about 3 seconds to turn on the device, press [M] key
to enter the system menu. Menu list:
Enroll
Dev ID
Delete
User
Time
Verify Mode
Language
Admin Setup
Workcode Scope
Admin Clear
Precision
System
Volume
Auto Off
5
Auto Update
6
Setup
Image Disp.
7
Log Alert
Log Setup
Re-Verify
8
Hardware Test Keypad, LCD, Voice, Sensor, Flash
9
System Info
10
:
Using the fingertip only. Moving finger during the process
of enrollment or verification.
Enroll
[OK]
ID 008101
Esc-C Set-OK (ID number range:0-999999)
Input user ID
Enroll FP
008101-1
Sav-OK
Press [OK] to save
Enroll PWD
[OK]
******
008101-P
Cancel-C Sav-OK
******
Press [OK] to save
Admin Setup Admin Setup Admin Setup
[OK] [OK] [OK]
ID 000000 008101
Esc-C Add-OK No-C Yes-OK
Input Admin ID
Set Time:
IN
09 : 00
26
10-11-17 WED
Other Setup
M→[User]→[OK]→[Verify Mode]→[OK]→[OK]→Input employee ID→[OK]→
Use [IN/ ]/[OUT/ ] to select 'ANY/PW+FP/ID+FP'→[OK]→[OK].
Item
Any Fingerprint only, Card only or ID+Password only
It requires both Password and Fingerprint verification
PW+FP
together
ID+FP Enter the user ID first, then verify the fingerprint
Factory default
setting
M→[Setup]→[OK]→[System]→[OK]→[Dev ID]→[OK]→
Dev ID:
Input the device's ID→[OK]→[C]→[OK].
Item
Device ID of the unit which is required in software
1-99999999
communication
Factory default
setting
M→ [Setup]→[OK]→[System]→[OK]→[WorkCode Scope]→[OK]
WorkCode:
→Input Max→[OK]→Input Min→[OK] →[C]→[OK].
Item
0-999999
Factory default
setting
Tips: WorkCode indicates the work type，easily distinguishes which
attendance record is related to which work type.
Wiring Diagram
Admin Setup
ID 008101
[OK]
Esc-C Add-OK
Setup successful
MENU System
▼ Setup
User System Dev ID 10000
[M] [OK] [OK]
 Setup  Time
Log Setup
System Info Hardware Test Language ENG
Select [Setup] Select [System] Select [Time]
M→[Setup]→[OK]→[System]→[OK]→[Language]→[OK]→
Use [IN/ ]/[OUT/ ] to select ENG/FRCH/GERM/...→[OK]→[C]→[OK].
Item
Explanation
Language
Factory default
setting
Any
Precision, Volume, Auto off, Auto Update, Image Disp., Log Alert, Re-Verify
Item
Precision
Explanation
Volume
Auto off
1
Auto Update
Image Disp.
Explanation
Valid scope for the Workcode
Log Alert
Max 999999
Min 0
Re-Verify
RJ11
PC USB Port
V1.2
Time MON Time THU
▼
00-00-0000 00:00 11-10-2010 15:30
[OK] [C]
Save?
↑
Set-C Next-OK No-C Yes-OK
Modify system time Press [OK] to save
Explanation
Contains 11 languages:
ENG(English), FRCH(French), GERM(German), SPAN(Spanish),
PTG(Portuguese), ITA(Italian), BULG(Bulgarian), SLVK(Slovak),
HUNG(Hungarian), SLVN(Slovenian), TURK(Turkish)
Related Language
Explanation
Set terminal fingerprint matching precision.
0-[Normal],1-[Good], 2-[Exact].
Set the terminal voice volume.
0-[mute], 5-[Max].
Set the time duration for an idle clock to go into sleep
mode.No-[Not Off], 250min-[Max Time].
Auto update means the previous lower quality fingerprint
template will be automatically replaced by the new higher
quality one during fingerprint verification.
Choose to display the fingerprint on the screen during the
verification process. [Yes] - show fingerprint image,
[No] - not show fingerprint image
The terminal will alarm when the memory capacity
is less than the [Log Alert] value.[No]-Not alarm,
Max. value 5,000.
The duration of time in which the terminal will ignore
repeated attempts for authentication.
[No]: Disable the function; Max. value is 250 min.