Universal Remote Control PalAmino4 Operating Instructions

Operating Instructions
1
Introduction
For The PalAmino4
The remote control is designed to operate
the PalAmino4 of Set-Top Boxes (STBs) and
4-Function Remote Control the majority of TVs, VCRs, DVDs and AUDIO
components on the market today, as shown
below.
TV : TVs, Plasma TVs and LCD TVs
VCR : VCRs and DVDs
AUX :Audio Receivers and Amplifiers, etc
2
Replacing Batteries
Before you program or operate the remote
control, you must install two new AAA alka-
line batteries.
STEP1 Remove the battery compartment
cover on the back of your remote
control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment
cover.
4
Operations
Device Default: PalAmino4 Set-Top Box.
Volume Default: TV volume and mute through
the TV , with the option of controlling volume and
mute through the STB or AUDIO component.
Refer to section E for programming the volume
and mute through your STB or AUDIO compo-
nent.
Channel Default: STB channel and number keys
through the STB, with the option of controlling
Universal Remote Control, Inc.
channel and number keys through the TV or VCR.
www.universalremote.com Refer to section F for programming the channel
OCE-0040A Rev 12(06/08/12) and number keys through your TV or VCR.
3
Button Functions
5
Programming the Remote Control
A. Three-Digit Code Programming Method.
The remote control can be programmed by pressing in a three-digit code number that
corresponds to a particular manufacturer and brand of Audio/Video component.
The three-digit code numbers are listed in the Set-up Code Tables on the backside of this
instruction manual.
STEP1 Turn on the A/V component you wish to program. (TV, VCR, DVD or AUX).
STEP2 Press the [COMPONENT] button (TV, VCR, DVD or AUX) to be programmed and
the [OK] button simultaneously for 3 seconds. The selected component LED light
will turn on indicating the component is ready to be programmed.
*Tip : If you do not begin entering code numbers within 20 seconds, the component LED
light will turn off and exit set-up mode and you will need to start over.
STEP3 Point the remote control toward the selected component and enter the three-digit
code number assigned to your brand from the code tables.
*Tip : The component will turn off when the
STEP4 Press the same [COMPONENT]
correct three-digit code number has been button to store the code. The
entered. You can verify you have selected the component LED light will blink
correct code by pressing the [POWER] but- twice to confirm that the code has
been stored.
ton. The component should turn on or off.
*Note : 2 colons If there is more than one
C. To Find the Three-Digit Code Number
three-digit number listed for your
That was Stored in the component.
brand, try one code number at a time
until your component turns off.
STEP1 Press the [COMPONENT] button
(TV, VCR, DVD or AUX) you wish to
STEP4 Store the three-digit code number
verify and the [OK] button simultane-
by pressing the same [COMPONENT]
ously for 3 seconds.
button once again. The component
*Tip : If you do not press the [INFO] button
LED will blink twice to confirm that the
within 20 seconds, the component LED
code has been stored.
light will turn off and exit set-up mode
*Note : Try all the functions on the remote
and you will need to start over.
control. If any of the functions do
STEP2 Press the [INFO] button. The com-
not work as they should, repeat from
ponent LED light will indicate the
Step 2 using the next three-digit code
three digits that comprise the code
number from the same brand list.
number by blinking the correspond-
ing number of times for each digit,
B. Auto Search Method.
separated by a one second interval,
If the three-digit code numbers assigned to
during which time the component
your brand do not turn off your component or LED light will turn off.
the code tables do not list your brand, you
Example : One blink, three blinks and eight
can use the Auto Search Method to find the
blinks, separated by a one second
correct three-digit code number for your
interval during which time the
component by performing the following
component LED light turns off,
steps:
indicates a code number of 138.
STEP1 Turn on the component you wish to
*Note : Ten blinks is equal to the number 0.
operate.
D. Programming AUX to operate a
STEP2 Press the [COMPONENT] button (TV,
fourth component (i.e., a second
VCR, DVD or AUX) to be programmed
TV, VCR, or DVD or AUDIO)
and the [OK] button simultaneously
for 3 seconds. The component LED
STEP1 Turn on the component you wish to
will turn on.
operate.
*Tip : If you do not press either the CH5 or
STEP2 Press the [AUX] button and the [OK]
CH6 button within 20 seconds, the
button simultaneously for 3 seconds.
component button LED light will turn off
The [AUX] LED light will turn on.
and exit set-up mode and you will need
*Tip : If you do not press the desired com-
to start over.
ponent button within 20 seconds,
the [AUX] LED light will turn off and
STEP3 Press the [CH5] or [CH6] button
exit set-up mode and you will need
one step at a time or keep it pressed.
to start over.
The remote will emit a series of
Power ON/OFF commands. Release
STEP3 Press the [COMPONENT] button you
the [CH5] or [CH6] button as soon
wish to operate.
as the component turns off.
STEP4 Point the remote control toward the
*Tip : You can verify that you selected the
component you want to program
correct code by pressing the [POWER]
and enter the three-digit code num-
button again. The component should
ber assigned to your TV brand from
either turn on or off.
the code tables.
*
Note : The [AUX] LED light will blink once F. Programming Channel Control.
for each button pressed. Once you
By following the steps below, the user can
enter the correct code number, the
program the channel controls (Channel Up,
component will turn off. If the com-
Channel Down and Last) from one compo-
ponent does not turn off, press the
nent to operate in another component mode.
next code numbers listed for your
The default channel control settings on the
brand until the component turns off.
remote control is as follows:
STEP5 Store the three-digit code number
STB : STB TV : STB
by pressing the [AUX] button once
VCR : VCR AUX : AUX
again. The component LED light will
blink twice to confirm that the code
If you wish to store the TV channel control
has been stored.
in TV mode, use the following steps.
*Note : Now turn on the component and test
STEP1 Press the [TV] button and the [OK]
the component functions on the
button simultaneously for 3 seconds
remote control. If any function does
until the TV LED light turns on.
not work properly, repeat from STEP
*Tip : If you do not press the [VOL 6 ] button
2 using the next code number listed
within 20 seconds, the TV LED light
for your component brand until you
will tiurn off and exit set-up mode
find a perfect match.
and you will need to start over.
STEP2 Press the [VOL 6 ] button.
E. Programming Volume Control .
STEP3 Press the [TV] button.
By following the steps below, the user can
program the volume controls (Volume Up,
The TV LED light will blink twice to confirm
Volume Down and Mute) from one device
the programming.
to operate in another device mode. The
To return to the original default state:
default volume control settings on the remote
control is as follows :
If you wish to restore the STB channel con-
trol in TV mode, repeat the above steps by
STB : TV TV : TV
pressing [STB] in STEP3 .
VCR : TV AUX : AUX
G. Low Battery Warning.
lf you wish to store the STB volume control
in STB mode, use the following steps.
When the battery is low and needs to be
replaced with fresh batteries, the remote
STEP1 Press the [STB] button and the
control component LED lights will blink 2
[OK] button simultaneously for 3
times in sequence whenever a [POWER]
seconds until the component LED
button is pressed to turn on components
light turns on.
*Tip : If you do not press the [VOL 5 ] button
H. Memory Lock System.
within 20 seconds, the component LED
This remote control is designed to retain
light will turn off and exit set-up mode
programmed memory for 10 years even
and you will need to start over.
after batteries are removed from the
STEP2 Press the [VOL 5 ] button.
remote control.
STEP3 Press the [STB] button.
I. Write your component Set-up codes.
The STB LED light LED will blink twice to con-
TV Set-up Code Number :
firm the programming.
VCR Set-up Code Number :
To return to the original default state:
AUX Set-up Code Number :
If you wish to restore the TV volume
control in STB mode, repeat the above steps
For additional information about your remote
by pressing [TV] in STEP3 .
control, go to www.universalremote.com