Universal Remote Control UR5L-9000L Operating Instructions

Operating Instructions For 1 4
Introduction Button Functions
PHAZR-5
The PHAZR-5 UR5L-9000L & UR5L-9020L is
designed to operate the CISCO / SA,
Pioneer, Pace Micro, Samsung and
Motorola digital set tops, Plus the majority
Cable Remote Control
of TV, AUD, DVD and AUX equipment on
the market as shown below.
CBL : Cable Set-top Box TV : Televisions
UR5L-9000L & UR5L-9020L AUD : Audio Receivers DVD : DVD Players
AUX : Media PC, Gaming System, etc.
2
Replacing Batteries
Before you program or operate the remote control,
you must install two new AA alkaline batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
5
Programming the Remote Control
3 IMPORTANT SETUP NOTE!
Operations
In this section when you are instructed to press a [DEVICE] button, that means to press either the CBL, TV, AUD,
DVD or AUX button, depending on what device you are programming the remote to operate.
DEFAULT STATE:
Device Default: Cable Set-Top Box (STB) There are four ways you can program your remote:
* Quick Set-Up Method
Channel Default: CABLE channel and numbers
* The Auto-Search Method
through the CABLE STB. You have the option of
controlling your CABLE channel and numbers The Quick Set-Up Method is a unique feature that enables the fastest and easiest setup by using a 1 digit
through the TV or AUD. Refer to section L for code. This is the quickest way to set up devices made by popular manufacturers.
programming steps.
The Pre-Programmed Code Method allows you to setup all of the buttons at once by entering 3-digit
code numbers that correspond with the components manufacture/brand. Code tables for this method
Volume Default: Volume and Mute control are
are on the backside of the operating instructions.
automatically transferred to the respective
Component based on the Device selected: The Auto-Search Method scans through all of the codes in the remote control, one at a time allowing you
to identify the correct code.
CBL:Cable Set-Top Box ; TV:TV ; AUD:AUD.
The Learning Method allows you to transfer functions from other remotes to the PHAZR-5one button at a time.
DVD:TV ; AUX:AUX. You have the option of
Universal Remote Control, Inc.
controlling CABLE Volume and Mute through IMPORTANT SETUP NOTE!
www.universalremote.com
the TV, DVD or AUD. Refer to section K for
This pertains to all programming steps. When you are in setup mode the device LED will light for 30 seconds. If you do
OCE-0087A Rev 09 (02/27/13)
programming steps.
not press a button within 30 seconds, the LED light will turn off and exit setup mode, and you will need to start over.
A. Quick Set-Up Method AUX
STEP1 Turn on the component you want to pro- Quick Number
gram. To program your TV, turn on the TV.
0
STEP2 Point the remote control at the compo-
1
nent.
2
STEP3 Press and hold the [DEVICE] key for 5 3
seconds until the Device LED will blink
4
once and stays on. Continue to hold the
5
[DEVICE] key and press the number key
6
assigned to your brand in the Quick
7
Set-up Code Table. The component
8
should turn off as soon as the number
9
key is pressed. (If it does not turn off,
release the [DEVICE] key and use the
C. Pre-Programmed 3-Dight Code Method
Pre-Programmed 3-Digit code Method
STEP1 Turn on the equipment that you want
or Scanning Method.)
the remote control to operate (Cable
STEP4 Release the [DEVICE] key to save the
Box, TV, DVD, etc.).
code. The Device LED will blink twice to
confirm that the code is stored. STEP2 Press the [DEVICE] button and the
[OK/SEL] button simultaneously for three
Repeat the steps above for all components (TV,
seconds. The corresponding device LED
AUD, DVD, AUX).
will turn on indicating that it is ready to
be programmed. The LED will remain on
B. Quick Set-up Code Tables
for 30 seconds. The next step must be
TV
entered while the LED is on.
Quick Number Manufacturer/Brand
STEP3 Point the remote control toward the
0 SANYO
equipment and enter the three-digit
1 SONY
code number assigned to your brand
2 SAMSUNG
from the code tables. If there are more
3 LG
than one three-digit number listed for
4 TOSHIBA
your brand, try one code number at a
5 PANASONIC
time until your equipment turns off.
6 PHILIPS
*Note : You can verify that you have selected the
7 HITACHI
correct code by pressing the [POWER]
8 SHARP
button. The equipment should turn back
9 VIZIO
on. Then try all of the functions on the
AUDIO
remote control (i.e. volume, mute, etc.) to
ensure you have the correct code. If any
Quick Number Manufacturer/Brand
of the functions do not operate as they
0 ROTEL
should, repeat the instructions from
1 DENON
STEP 3 above using the next three digit
2 YAMAHA
code number from the brand list.
3 MARANTZ
4 SONY STEP4 Store the three-digit code by pressing the
5 INTEGRA same [DEVICE] button once again. The
6 HARMAN KARDON
device LED will blink twice to confirm that
7 PIONEER
the code has been stored.
8 ONKYO
* The Pre-Programmed 3-Digit Code Method
D. Auto-Search Method
9 LEXICON
* The Learning Method
If none of the three digit code numbers assigned to
DVD
your brand of equipment works, or the code table
Quick Number Manufacturer/Brand
does not list your brand, you can use the Auto
0 HITACHI
Search Method to find the correct three-digit code
1 SONY
number for your equipment by following steps:
2 PHILIPS
STEP1 Turn on the equipment that you want
3 SAMSUNG
the remote control to operate (Cable
4 PHILIPS MAGNAVOX
Box, TV, DVD, etc.).
5 PANASONIC
STEP2 Press the [DEVICE] button and the
6 LG
[OK/SEL] button simultaneously for
7 JVC
three seconds. The device LED will turn
8 DENON
on indicating that it is ready to be
9 PIONEER
programmed. The LED will remain on STEP1 Press the [DEVICE] and [ASPECT] buttons
for 30 seconds. The next step must be
simultaneously for 3 seconds until the
Manufacturer/Brand
entered while the LED is on. Device LED light turns on.
BOSE
STEP3 Press the [CH5] or [CH6] button one at
STEP2 Press and hold both the [DEVICE] button
HP
a time or keep it pressed. The remote
you want to erase and the [PAUSE] button
APPLE / iPod
will emit a series of Power ON/OFF
for 5 seconds. The Device LED will blink
APPLE / iPod code signals. Release the [CH5] or [CH6]
twice to confirm the erasure.
MICROSOFT / XBOX button as soon as the equipment turns off.
STEP3 To exit, press and hold both the [DEVICE]
SONY / PS2
*Note : You can verify that you have selected the
and [ASPECT] buttons simultaneously
LUTRON
correct code by pressing the [POWER]
X-10
button. The equipment should turn back
H.To Identify the 3-Digit Code
X-10 on. Then try all of the functions on the
Programmed for a Device
MICROSOFT / XBOX remote control (i.e. volume, mute, etc.) to
ensure you have the correct code. If any of
STEP1 Press the appropriate [DEVICE] button
the functions do not operate as they should,
and the [OK/SEL] button simultaneously
repeat the instructions from STEP 3 above
for three seconds. The device LED will
to continue the Auto Search Method.
turn on for 30 seconds. The next step
STEP4 Press the same [DEVICE] button to store
must be performed while the LED is on.
the code. The Device LED will blink twice
STEP2 Press the [INFO] button. The device LED
to confirm that the code has been stored.
will blink a number of times indicating
E. The Learning Method the number of each digit for the code.
Each digit is separated by a one second
STEP1 Press the [DEVICE] button (TV,AUD, DVD,
interval of the LED being off.
or AUX) to be programmed and the
[ASPECT] buttons simultaneously for 3 Example :One blink, (pause) three blinks,
seconds until the Device LED light turns on.
(pause) eight blinks indicates the
STEP2 Point the PHAZR-5 at the other remote, code number 138.
head-to-head, 1 or 2 inches apart.
*Note : Ten blinks indicates the number 0.
STEP3 Press the button on the PHAZR-5 that
I. Programming the AUX Device
you want to teach a command to. For
example, press the [MUTE] button to
You can take advantage of the AUX function to
learn a command to the [MUTE] button.
program a devices such as a media PC, gaming
STEP4 Press and hold the button on the other console or satellite radio receiver. Follow the
remote that corresponds to the command instruction in section C to program an AUX
you want to teach until the PHAZR-5
device. You can also program the AUX button for
Device LED light blinks twice. a second TV, DVD or Audio Device. To do this
follow the instructions below.
*Note : The LED will blink 5 times if there
was an error in the learning process.
STEP1 Turn on the 5th device you want to
Repeat STEPS 3 and 4 if this occurs. program (TV, AUD, DVD, etc.).
Continue learning other buttons by
STEP2 Press the [AUX] button and the
repeating STEPS 3 and 4.
[OK/SEL] button simultaneously for 3
STEP5 Once you have completed teaching the seconds. The [AUX] device LED will
PHAZR-5 all desired commands for the turn on for 30 seconds.
component, save the learned commands
STEP3 Press the [Device] button For the type of
by pressing the [DEVICE] and [ASPECT]
device you want to setup. Point the remote
buttons simultaneously until the Device
control toward the device and enter the
LED blinks 3 times. Now test all of the
3-digit code number assigned to your brand.
buttons to make sure they operate correctly.
*Note : To program a second TV press TV, etc.
F. Erasing a Single Learned Command
STEP4 When the equipment turns off verify
STEP1 Press the [DEVICE] and [ASPECT] buttons
that you have selected the correct
simultaneously for 3 seconds until the code by pressing the [POWER] button.
Device LED light turns on.
The equipment should turn back on.
Then try all of the functions on the
STEP2 Press and hold the button you want to
remote control (i.e. volume, mute, etc.)
erase for 3 seconds. The Device LED
to ensure you have the correct code.
will blink twice to confirm the erasure.
If any of the functions do not operate as
STEP3 To exit, press and hold both the [DEVICE]
they should, enter the next 3-digit code
and [ASPECT] buttons simultaneously
number from the brand list.
until the Device LED blinks 3 times.
STEP5 Once you have found the correct 3-digit
G. Erasing All Learned Commands code, save it by pressing the [AUX] button
one more time. The [AUX] LED light will
from One Device
blink twice to confirm the code was stored.
J. Programming the System On/Off Button *Note : To return TV device to CBL channel 6
Set-up Code Tables
repeat steps above replacing [TV] with
This allows you to program the System On/Off
[CBL] in Step 3. CBL-CABLE Converters
button so it can send up to five power On/Off
commands with one button press.
Manufacturer/Brand
M. Programming a 'Macro' button.
STEP1 Press the [CBL] button.
CISCO/SA
If your remote model has custom-programmable
STEP2 Press the [SYSTEM ON/OFF] button PIONEER
Macro buttons available(See Section 4), they can
and the [OK/SEL] button simultaneously
PACE
be programmed to act as a 'Macro' or Favorite
for 3 seconds. The [CBL] button will turn SAMSUNG
Channel button in CABLE mode. This allows you to
on for 30 seconds.
MOTOROLA
program up to five 2-digit channels, four 3-digit
CE-LABS
STEP3 Press the first [DEVICE] button you want to
channels or three 4-digit channels that can be
DIGEO
store in the [SYSTEM ON/OFF] button and
accessed with one button press.
EVOLUTION FTA 158
then the [POWER] button. Repeat this for
GENERAL INSTRUMENT
STEP1 Press the [CBL] button to select the CBL
other Components until you have stored
HAMLIN
mode.
all the desired power commands into the
HITACHI
[SYSTEM ON/OFF] button.
STEP2 Press the [MACRO] button and
JERROLD
STEP4 Press the [CH5] button to save the [OK/SEL] button simultaneously for MAGNAVOX
power commands you stored. The 3 seconds. The [CBL] button will turn MEMOREX
[CBL] button will blink twice to confirm MOXI
on for 30 seconds.
the commands have been saved. NFUSION
STEP3 Enter the the 2, 3 or 4-digit code for the
PANASONIC
channel you want programmed first
K. Programming Volume Control PHILIPS
(for example, 007) using the Number
PULSAR
Volume and Mute control are factory programmed
Pad, then press the [STOP] button. RCA
to automatically transfer to the respective
Then enter the code for the next chan- REGAL
Device mode You select, as follows:
nel (for example, 050), then press the REGENCY
CBL : CBL T V : TV AUD : AUD SKY
[STOP] button. Repeat this process for
DVD : TV AUX : AUX SONY
the third channel. The [CBL] button will
SPRUCER
If you wish to store the TV volume control in CBL blink once for each channel entered.
TELNET
mode, use the following steps.
STEP4 Press the [CH5] button to store the
TOCOM
STEP1 Press the [OK/SEL] button and [CBL]
channels that were selected. The TOSHIBA
button simultaneously for three VIEWSTAR
[CBL] button will blink twice to confirm
seconds. The device LED will turn on
the storage of commands. ZENITH
for 30 seconds. The next step must
To access the programmed channels, press the TV
be performed while the LED is on.
[MACRO] button once. This will bring up the
STEP2 Press the [VOL5] button. The device Manufacturer/Brand
first channel. Press once again and it will bring
LED will blink.
up the second channel. Press again and it will A MARK
STEP3 Press [TV] button. The device LED will
bring up the third channel. ABEX
blink twice to confirm the programming. ACCURIAN
N. Low Battery Warning ADMIRAL
*Note : To return CBL device to CBL volume
AD NOTAM
repeat steps above replacing [TV] with
When the batteries are low and need to be
ADVENT
[CBL] in Step 3 .
replaced with fresh batteries, the Device LED
ADVENTURA
lights will blink 2 times in sequence whenever a
AFFINITY
L. Programming Channel Control
[POWER] button is pressed to turn on equip-
AIKO
ment.
You can program the channel controls (Channel AKAI
Up, Channel Down, Last and Numbers) from
O. Memory Lock System
ALBATRON
one Device to operate in another Device mode.
ALERON
Default channel control settings on the remote This remote control is designed to retain
AMERICA ACTION 043
control are as follows: programmed memory for 10 years even after
AMPRO
batteries are removed from the remote con-
CBL : CBL T V : CBL AUD : AUD
AMSTRAD
trol.
DVD : DVD AUX : AUX
ANAM
AOC
If you wish to store the TV channel controls in TV
P. Record Your Component Set-up
APEX
mode, use the following steps.
Codes APEX DIGITAL
STEP1 Press the [OK/SEL] button and [TV] button
AQUAVISION
TV Set-up Code Number:
simultaneously for three seconds. The
ASTAR
device LED will turn on for 30 seconds. AUDIOVOX
AUD Set-up Code Number:
The next step must be performed while
AVENTURA
DVD Set-up Code Number:
the LED is on. AVIELO
AUX Set-up Code Number: AVION
STEP2 Press the [VOL6] button. The device
AXION
For additional information about your remote
LED will blink.
BELCOR
control, go to www.universalremote.com
STEP3 Press [TV] button. The device LED will BELL&HOWELL 333 072
blink twice to confirm the programming. BENQ
TV
Manufacturer/Brand Set-Up Code Number
BOXLIGHT 266
Set-Up Code Number BRADFORD 043
BROCKWOOD 116
001 003 041 042 045 046
BROKSONIC 238
001 103 034 051 063 076 105
BYDESIGN 031 032
001 005 002
CANDLE 116 002 003 363
001 030
CAPEHART 058
002 111 148
CARY AUDIO DESIGN 266
164
CELEBRITY 001
153
CENTURION 116
CETRONIC 043
005 103 104
CHANGHONG 247
049 050 055
CITIZEN 116 002 003 363 043 258 103 143
103 055
CLARION 043
005 004 103 005 003 008 009 010 069
CLASSIC 043
010 012
CLP CLASSIC 333
052
COBY 640 641 671
111 252 153
COLORTYME 116
192 CONCERTO 363
044 047
CONCIERGE 073
006 012 013 020 085
CONTEC 043 050 051
052 CORNEA 116
047 CORONADO 143
049 050
CRAIG 043 054
057 CROSLEY 164
230 204 CROWN 043 143
108 CURTIS MATHES 116 258 363 143
047 CXC 043
354 CYBERHOME 015
DAEWOO 363 016 043 044 076 103 114 125 127
039 040 056
052 143
012 015 DAYTRON 363 143
DELL 320 164 363 618
052 060 093 100
DIGITAL PROJECTION 570
DIMENSIA 333
DREAMVISION 235
Set-Up Code Number
DUKANE 011 025
112 143 DUMONT 116 073
DURABRAND 096 052
025
DWIN 257
036
072 251 333 DYNASTY 043
DYNEX 400
672
EIKI 187
247 388
ELECTROBAND 001
002
ELECTROGRAPH 466
680
ELECTROHOME 143 024 076 196
103
ELEKTRA 072
116 146 248 404 405 473 475 323 387
ELEMENT 363 494 526 622
391 615
EMERSON 028 048 043 155 005 116 363 047 050
017
051 076 096 143 153 154 052 514
028
ENVISION 116
EPSON 324 590
073
ESA 323
052
FISHER 007 057
043 054 056 080 112
FUJITSU 246 198 410
116 363 112 058 616
FUNAI 028 043 052
572
FUSION 642
006
FUTURETECH 043
573 574
GATEWAY 242 268
477
GE 073 116 008 009 034 056 074 155 333
076 454 388
363
052
GEM 391
627 628
441 GIBRALTER 116 073
GO VIDEO 026
039
GOLDSTAR 113 116 102 363 106 112 127 143
116
GPX 674
GRUNPY 028 043
423 600