Miele WTZH 730 WPM Quick Start Manual

Applications Operation
ɉ Before using the washer-dryer for
the first time, ensure that it is correctly
installed and connected. Install and
connect the appliance as described in the
operating instructions.
It is essential to read the separate
operating instructions.
1 Display with sensors 6 Dispensing buttons
See points 11 to 16 for more For selecting automatic detergent
information. dispensing and CapDosing.
2 Start/Stop button 7 Options buttons
You can use this washer-dryer to: For starting the programme selected Various options can be added to the
and cancelling a programme once it has programmes.
– wash separately started. 8 Programme selector
with a maximum load of 8.0 kg, 3 Temperature button For selecting washing and drying
For selecting a wash temperature. programmes.
– dry separately 4 Spin speed button 9 Optical interface
with a maximum load of 5.0 kg, For selecting the spin speed. For service technicians.
5 Drying level button 10  button
or For selecting the drying level. For switching the washer-dryer on and
off.
– wash and dry in a continuous
sequence
with a maximum load of 5.0 kg.
Environmentally friendly washing and drying
– Load the maximum amount for the – Use the Express programme for small,
programme you are using. lightly soiled loads.
– When smaller amounts of laundry are – Modern detergents make it possible
washed, the Auto load control system to wash at lower temperatures (e.g.
will reduce the amount of water and 20°C). Using lower temperature
energy used. settings will save energy.
Separate washing
1. Preparing the laundry
ĺ
Empty all pockets.
ɉ Foreign objects (e.g. nails,
coins, paper clips etc.) can
cause damage to fabrics and to
components in the machine.
ĺ
Sort the laundry by colour and by care label. Most
garments have a textile care label in the collar or side
seam.
ĺ
Pre-treat stains and badly soiled areas (see the booklet
11  sensor "Miele's guide to laundry care").
Scrolls down the list to the next option
or decreases a value.
12 OK sensor 2. Selecting a programme
Confirms the programme selected, a
value set or opens a sub-menu. Switching the washer-dryer on
ĺ
13  sensor Press the  button.
Scrolls up the list to the next option or
increases a value. Selecting a programme via the programme selector
ĺ
14 Washing sensor Turn the programme selector to the required
For selecting the washing function. programme.
15 Drying sensor The maximum load for the wash programme selected will
For selecting the drying function. appear in the display. This will then be replaced by the
Delay start sensor 3
16 standard display.
For selecting Delay start.
Selecting a programme via "Further programmes"
ĺ
Turn the programme selector to Further programmes. 1 Detergent dispenser drawer
ĺ
Touch the  or  sensor until the programme you want 2 Control panel
appears in the display. 3 Access to filters, pumps and
ĺ
emergency release
Confirm the programme with the OK sensor.
The maximum load for the wash programme selected will 4 Door
appear in the display. This will then be replaced by the 5 Access panel for TwinDos
standard display. containers
– For precise dispensing, use automatic 3. Loading the drum
detergent dispensing.
– Selecting the highest possible spin Opening the door Closing the door
ĺ ĺ
speed for the wash programme will Reach under the door grip and pull the door open. Make sure that no items are caught between the door
save energy when drying in a tumble The load display will appear. and the seal.
ĺ ĺ
dryer afterwards. Unfold the laundry and load loosely in the drum. Shut the door with a gentle swing.
ĺ
Pay attention to the load indication. The display will ask you to enter the degree of soiling of
the laundry.
4. Selecting programme settings 6. Starting the programme
ĺ
Press the flashing Start/Stop button.
1 2
Selecting the degree of soiling The door will lock and the programme will
ĺ
Select the degree of soiling with the  or  sensor and start.
confirm with OK. The programme status will appear in the
The dosage display will appear. display.
ĺ Confirming the detergent dosage display
Confirm with OK. 7. At the end of the programme
The door remains locked during the anti-
Selecting the temperature crease phase.
ĺ ĺ
Press the Temperature button. Press the Start/Stop button.
ĺ ĺ
Set the temperature you want with the  and  Pull open the door.
ĺ
sensors and confirm your selection with the OK sensor. Remove the laundry.
ɉ Check that all items have been
Selecting the spin speed
ĺ
removed from the drum.
Press the Spin speed button.
ĺ ĺ
Set the spin speed you want with the  and  sensors Check the folds in the door seal for any
and confirm your selection with the OK sensor. small articles, e.g. buttons, which might
be lodged there.
Selecting options Note: For safety reasons, close the door.
ĺ ĺ
Use the ProgrammeManager, Stains or Further options Switch the washer-dryer off with the
buttons for selecting the options you want.  button.
ĺ
Remove any used capsules from the
Selecting Delay start detergent dispenser drawer.
ĺ
4 5
Select a Delay start time if required. Leave the detergent dispenser drawer
slightly open to allow it to dry.
See the section "After each washing
5. Adding detergent
or drying programme" in the chapter
Detergent can be dispensed via TwinDos, via the
"Washing and drying in a continuous
detergent dispenser drawer or with Caps.
sequence".
TwinDos
The optimum amount of UltraPhase 1 and UltraPhase 2
will be dispensed automatically according to the colour
mix of the load.
ĺ
Press the TwinDos button.
Detergent dispenser drawer
ĺ
Pull out the detergent drawer and add detergent to the
compartments ,  or .
CapDosing
There are different types of capsules available.
Each capsule contains the correct amount of detergent for
one wash cycle.
ĺ
Press the Cap  button, select the type of capsule
and place a capsule in the  compartment.
Separate drying
DRYING
Selecting drying Selecting thermospin
ĺ ĺ
Touch the Washing and Drying sensors ĺ Press the Spin speed button.
If you have washed a full load of laundry
until just the Drying indicator light remains Set the spin speed you want with the 
and you wish to dry the laundry in the
on. and  sensors and confirm your selection
washer-dryer afterwards, you will have
with OK.
to remove half the load and carry out the The Washing indicator light must not be
drying process in two loads. lit up as this would mean that the relevant
Selecting options
wash programme would begin before the ĺ
Select the option you want using either
drying process.
1. Preparing the laundry the ProgrammeManager or Further
ĺ
Sort the laundry according to the type options button.
3. Loading the drum
of fibre and weave, garment care label
symbol and the drying level required. Selecting Delay start
ĺ ĺ
Before drying, check the drying symbol Opening the door Select a Delay start time if required.
ĺ
on the care label. Reach under the door grip and pull the
door open.
ĺ
Load the laundry loosely in the drum. 5. Starting the programme
ĺ
2. Selecting a programme
Press the flashing Start/Stop button.
Do not overload the drum. Overloading
The door will lock and the drying
can cause unnecessary wear and tear of
Switching the washer-dryer on programme will start.
ĺ the laundry, give a disappointing drying
Press the  button. result and cause more creasing. The programme status will appear in the
display.
ĺ
Selecting a programme via the Remove foreign objects like detergent
The mains water tap must be kept open
programme selector dispensing devices from the laundry.
ĺ for drying.
Turn the programme selector to the
ɉ They can melt and damage the dryer
required programme.
and the laundry.
6. At the end of the programme
Selecting a programme via "Further The door remains locked during the anti-
programmes" Closing the door crease phase.
ĺ ĺ ĺ
Turn the programme selector to Further Shut the door with a gentle swing. Press the Start/Stop button.
ĺ
programmes. Make sure that no items are caught The door will be unlocked.
ĺ
Touch the  or  sensor until the between the door and the seal.
If you have unloaded the drum during the
programme you want appears in the anti-crease phase, make sure you spread
display.
ĺ out the laundry to cool it down.
4. Selecting programme settings
Confirm with OK.
ĺ
Pull open the door.
ĺ
Selecting the drying level Remove the laundry.
The maximum load for the wash ĺ
Press the Drying level button.
programme selected will appear in the See the section "After each washing
display. This will then be replaced by the Select the drying level or duration you want or drying programme" in the chapter
with the  and  sensors and confirm your
standard display. "Washing and drying in a continuous
selection with OK.
sequence".
ĺ
Switch the washer-dryer off.
Changing the programme sequence
Cancelling a programme
Changing the spin speed
ĺ
Press the Start/Stop button and select – is possible up to the start of the spin
Cancel programme. cycle.
ĺ ĺ
Touch the OK sensor. Press the Spin speed button and change
The suds will be drained away or the the spin speed.
laundry will be cooled down before the door
can be opened. Changing the drying level / drying
duration
Removing the laundry – is possible while a wash programme is
ĺ
Pull the door open and unload the drum. running.
ĺ
Press the Drying level button and change
Selecting another programme the drying level.
ĺ
Close the door.
ĺ
ĺ Select the required programme. Selecting or deselecting drying
Press the Start/Stop button. – is possible while a wash programme is
running.
ĺ
Touch the Drying sensor.
Interrupting a programme
ĺ
Switch the washer-dryer off with the Changing options
ĺ  button. – Some options can be selected or
To continue the programme, switch the deselected after a programme has
washer-dryer back on with the  button. started.
Changes cannot be made while the safety
ɉ Do not switch the washer-dryer off
lock is active.
before the end of a drying programme. If
this is done, all items must be removed
immediately and spread out to cool down.
Adding or removing laundry
You can add or remove items during the
first few minutes after the programme has
Changing
started.
ĺ
Press the Start/Stop button.
ĺ
Changing a programme Add laundry
Select using the  or 
– after the programme has started is not sensor.
possible.
If this message does not appear in the
display, then it is no longer possible to
Changing the temperature
add or remove items of laundry.
– is possible up to 5 minutes after the
ĺ
programme has started (not with the Confirm with OK.
Cottons programme). The programme will stop and the door will
ĺ
Press the Temperature button. unlock.
ĺ ĺ
Change the temperature using the  or Pull open the door and add or remove
 sensors and confirm your choice with items.
ĺ
OK. Close the door.
ĺ
Press the Start/Stop button.
ĺ
The programme will continue.
WTZH 730 WPM en - AU, NZ M.-Nr. 10 868 090/00