Tsubaki T-ACE Instruction Manual

・ l Do not wet the product with water or oil nor give shock to it such as by dropping it. The product may fail.
・ l Do not disassemble or modify the product. Such a practice may cause fire or electric shock.
・ l Do not keep the product in places that are humid, hot or filled with dust.
・ l When the product will not be used, remove the battery and keep the product in the case.
・ l Do not bend the sensor microphone. To pull it out, hold the connector. Otherwise the product may fail.
!
Danger Do not use the product when the belt is running. Otherwise, your hand may get caught.
● PX tooth profile Unit: kg/m
Width Width
Type MASS Type
(㎜) (㎜)
4 0.006 40
P2M
6 0.008 60
UP14M
10 0.014 80
6 0.013 100
P3M
10 0.022 120
UP3M
15 0.034
10 0.041 6
P5M
DP3M
15 0.062 10
UP5M
25 0.103 15
15 0.084 10
25 0.139 DP5M 15
P8M
40 0.223 25
60 0.334
40 0.393 15
60 0.589 25
DP8M
P14M 80 0.786 40
100 0.982 60
120 1.178
15 0.076 40
25 0.127 60
UP8M DP14M
40 0.203 80
60 0.304 100
120
Basic formula
Tsubaki Belt Tension Meter T-ACE calculates the tension
using the following formula:
･Frequency
１ Ｔ
Ｆ ＝
２Ｌ Ｗ
･Belt tension
２ ２
Ｔ ＝ ４ × Ｗ × Ｌ × Ｆ
T: Belt tension
L: Span length
W: Belt unit mass
※ Even if the mounting tension is adequate, the vibration frequency may be out of the
measurable range of the product depending on a combination of measuring conditions used.
(A particular attention is required when the span length exceeds 1 m.)
T-ACE Instruction Manual
Thank you for your selection of Tsubaki Belt Tension Meter T-ACE.
(Measurement is possible only when the belt is at a stop.)
● Trapezoidal tooth profile
Width
Nominal
MASS Type MASS
Width (㎜)
0.304 3.2 3.2 0.004
0.456 4.8 4.8 0.006
MXL
0.608 6.4 6.4 0.008
0.760 9.5 9.5 0.012
0.912 12.7 12.7 0.016
0.015 025 6.4 0.017
0.025 031 7.9 0.021
XL
0.038 037 9.5 0.026
0.038 050 12.7 0.035
0.058 050 12.7 0.048
L
0.096 075 19.1 0.073
100 25.4 0.097
0.088 075 19.1 0.101
0.148 100 25.4 0.135
0.237 H 150 38.1 0.202
0.355 200 50.8 0.269
300 76.2 0.404
0.417 200 50.8 0.635
XH
0.626 300 76.2 0.953
0.835 400 101.6 1.270
1.043
1.252
･Span length
(Ｄｐ－ｄｐ)
２
Ｌ ＝ Ｃ －
４
F: Frequency
Dp: Large pulley pitch diameter
dp: Small pulley pitch diameter
c: Distance between shafts
For Safe Use
List of Unit Mass
Unit: kg/m ● Urethane
Width
Nominal
Type MASS Type
Width (㎜)
200 50.8 0.818
MXL
300 76.2 1.227
XXH
400 101.6 1.636
500 127.0 2.045
025 6.4 0.012
DXL
031 7.9 0.015
037 9.5 0.018
050 12.7 0.042
DL
075 19.1 0.062
100 25.4 0.083
075 19.1 0.084
100 25.4 0.112
DH 150 38.1 0.169
200 50.8 0.225
300 76.2 0.337
Model
Measuring range
Belt span length
Unit mass
２
Working temperature
Power supply
Mass and dimensions
Accessories
Width
Nominal
MASS Type
Width (㎜)
3.2 3.2 0.005
4.8
4.8 0.007
T2.5
6.4
6.4 0.009
025 6.4 0.015
031 7.9 0.019
T5
037 9.5 0.023
XL
050 12.7 0.034
075
19.1 0.052
100
25.4 0.068
037 9.5 0.036
050 12.7 0.046
T10
075 19.1 0.069
L
100 25.4 0.091
150
38.1 0.146
200
50.8 0.194
050 12.7 0.068
T20
075 19.1 0.096
100 25.4 0.127
H 150
38.1 0.191
200
50.8 0.254
300
76.2 0.380
400
101.6 0.538

Specifications

BDTM101
0.1～9999N , 30～600Hz
0.001～9.999m
0.001～9.999㎏/m
－10～60℃
Dry cell (AAA) x 4 pieces
160 g (main unit)
162 long x 61.6 wide x 30 thick in ㎜
Sensor microphone,
dry cells (AAA x 4 pieces), carrying case
Unit: kg/m
Width Width
MASS Type MASS
(㎜) (㎜)
3 0.005 10 0.038
5 0.008 15 0.057
AT5
7 0.011 25 0.095
10 0.015 50 0.190
5 0.016 25 0.170
AT10
10 0.032 50 0.340
15 0.048 75 0.510
20 0.064 50 0.550
AT20
25 0.080 75 0.825
15 0.075 5 0.012
20 0.100 10 0.024
DT5
25 0.125 15 0.036
50 0.250 20 0.047
75 0.375
25 0.180 15 0.079
DT10
50 0.360 20 0.106
75 0.540 25 0.132