AMG AMG9162M-H User Manual
  1. Manuals
  2. Brands
  3. AMG Manuals
  4. Switch
  5. AMG9162M-H
  6. User manual

AMG AMG9162M-H User Manual

16 port 10/100tx + 2 port 10/100/1000t/mini-gbic combo managed industrial redundant ring switch
Hide thumbs
Table of Contents

Advertisement

Quick Links

16 Port 10/100TX + 2 Port 10/100/1000T/Mini-GBIC
Combo Managed Industrial Redundant Ring Switch
AMG9162M-H

User Manual

www.amgsystems.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AMG9162M-H and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for AMG AMG9162M-H

Summary of Contents for AMG AMG9162M-H

  • Page 1: User Manual

    16 Port 10/100TX + 2 Port 10/100/1000T/Mini-GBIC Combo Managed Industrial Redundant Ring Switch AMG9162M-H User Manual www.amgsystems.com...

  • Page 2: Fcc Warning

    FCC Warning This Equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy.

  • Page 3: Table Of Contents

    Content Introduction..............1 Features..............1 Software Specifications..........3 Package Contents............ 5 Hardware Description ..........1 Physical Dimensions..........1 Front Panel .............. 1 Top View ..............2 LED Indicators ............3 RJ-45 Pin Assignments..........5 Cabling..............8 SFP Connection............9 Wiring the Power Inputs......... 12 Wiring the Fault Alarm Contacts ......
  • Page 4 System Commands Set ........... 22 Port Commands Set ............25 Trunk Commands Set ............27 VLAN Commands Set............29 Spanning Tree Commands Set ........30 QOS Commands Set ............33 IGMP Commands Set ............34 Mac / Filter Table Commands Set ........34 SNMP Commands Set.............
  • Page 5 System Event Log – Syslog Configuration..... 54 System Event Log - SMTP Configuration ....55 System Event Log - Event Configuration ....56 Fault Relay Alarm ..........59 SNTP Configuration ..........59 IP Security.............. 62 User Authentication..........63 Port Statistics ............64 Port Control............
  • Page 6 QoS Policy and Priority Type ........... 90 Port-based Priority ............91 COS Configuration............92 TOS Configuration ............92 IGMP Configuration ..........93 X-Ring ..............94 Security ..............97 802.1X/Radius Configuration ........... 97 MAC Address Table............100 Factory Default............. 103 Save Configuration ..........103 System Reboot ............

  • Page 7: Introduction

    Introduction The managed industrial switch is a cost-effective solution and meets the high reliability requirements demanded by industrial applications. Using fiber port can extend the connection distance that increases the network elasticity and performance. Features System Interface/Performance » RJ-45 ports support Auto MDI/MDI-X Function »...
  • Page 8 » Support 802.1 Q Tag VLAN » GVRP X-Ring » X-Ring, Dual Homing and Couple Ring Topology...
  • Page 9 » Provide redundant backup feature and the recovery time below 20ms Port Trunk with LACP Support IEEE802.1ab LLDP QoS (Quality of Service) » Support IEEE 802.1p Class of Service » Per port provides 4 priority queues » Port Base, Tag Base and Type of Service Priority Bandwidth Control »...
  • Page 10 » Air Discharge: 8KV » Contact Discharge: 6KV...

  • Page 11: Software Specifications

    Software Specifications SNMP v1, v2c and v3 management Web interface management Management Telnet interface management Command Line Interface (CLI) management RFC 1215 Trap RFC 1213 MIBII RFC 1157 SNMP MIB RFC 1493 Bridge MIB SNMP MIB RFC 2674 VLAN MIB RFC 1643 RFC 1757 RSTP MIB...
  • Page 12 Supports 100 entries of MAC address for static MAC and Port Security another 100 for MAC filter TX packet only RX packet only, Port Mirroring Both of TX and RX packets Supports IGMP snooping v1, v2 and v3 IGMP Up to 256 multicast groups and IGMP query Supports 10 IP addresses that have permission to access IP Security the switch management and to prevent unauthorized...

  • Page 13: Package Contents

    Supports Primary and Secondary DNS Server Supports SNTP to synchronize system clock with an SNTP Internet time server TFTP firmware update Firmware Update TFTP configuration backup/restoration Configuration Supports binary configuration file for system quick Upload and installation Download Package Contents Please refer to the package content list below to verify them against the checklist.

  • Page 14: Hardware Description

    Hardware Description In this paragraph, we will describe the Industrial switch’s hardware spec, port, cabling information, and wiring installation. Physical Dimensions 16 10/100TX + 2 10/100/1000T/Mini-GBIC Combo w/ X-Ring L2 Managed Industrial Switch dimensions (W x H x D) are 72mm x 152mm x 105mm Front Panel The front panel of the 16 10/100TX + 2 10/100/1000T/Mini-GBIC Combo w/ X-Ring L2 Managed Industrial Switch is shown as below:...

  • Page 15: Top View

    Top View The top panel of the 16 10/100TX + 2 10/100/1000T/Mini-GBIC Combo w/ X-Ring L2 Managed Industrial Switch has one terminal block connector with six contacts. Top Panel of the industrial switch...

  • Page 16: Led Indicators

    LED Indicators The diagnostic LEDs located on the front panel of the industrial switch provide real-time information of system and optional status. The following table provides description of the LED status and their meanings for the switch. Status Meaning Green System power on No power inputs The industrial switch is the master device of the...
  • Page 17 Yellow Ethernet port full duplex (Lower LED) Blinking Collision of packets occurs (Lower LED) Ethernet port half duplex or not connected to (Lower LED) network Green Connected to network (Upper LED) Blinking Networking is active (Upper LED) P17 ~ P18 Not connected to network (10/100/1000T) (Upper LED)

  • Page 18: Rj-45 Pin Assignments

    RJ-45 Pin Assignments The UTP/STP ports will automatically sense for Fast Ethernet (10Base-T/100Base-TX) or Gigabit Ethernet (10Base-T/100Base-TX/1000Base-T) connection. Auto MDI/MDIX means that the switch can connect to another switch or workstation without changing straight through or crossover cabling. See the illustrations below for straight through and crossover cable schema.
  • Page 19 10/100Base-TX Cable Schema Schema Straight Through Cable Crossover Cable Schema 10/100/1000Base-T Pinouts The table below describes the gigabit Ethernet RJ-45 pinouts. Signal name Description BI_DA+ Bi-directional pair A+ BI_DA- Bi-directional pair A- BI_DB+ Bi-directional pair B+ BI_DC+ Bi-directional pair C+ BI_DC- Bi-directional pair C- BI_DB-...
  • Page 20 10/100/1000Base-T Cable Schema The following two figures illustrate the 10/100/1000Base-T cable schema. Straight Through Cable Schema Crossover Cable Schema...

  • Page 21: Cabling

    Cabling Use four twisted-pair, Category 5e or above cabling for RJ-45 port connection. The cable between the switch and the link partner (switch, hub, workstation, etc.) must be less than 100 meters (328 ft.) long. Gigabit Copper/SFP (mini-GBIC) combo port: The Industrial switch has the auto-detected Giga port—Gigabit Copper/SFP combo ports.

  • Page 22: Sfp Connection

    SFP Connection To connect the transceiver and the LC cable, please follow the steps shown below: First, insert the transceiver into the SFP slot. Notice that the triangle mark indicates the bottom of the slot. Insert transceiver into the SFP slot Transceiver Inserted...
  • Page 23 Second, insert LC connector of the fiber cable into the transceiver. LC connector to the transceiver...
  • Page 24 SFP Disconnection To remove the LC connector from the transceiver, please follow the steps below: First, press down the latches and pull the LC connector out of the transceiver. Press down the latches to remove the LC connector Second, push down the metal loop and pull out the transceiver by the handle. Pull the transceiver out of the slot...

  • Page 25: Wiring The Power Inputs

    Wiring the Power Inputs Please follow the steps below to insert the power wire. 1. Insert the positive and negative wires into the V+ and V- contacts on the terminal block connector. 2. Tighten the wire-clamp screws to prevent the DC wires from loosing.

  • Page 26: Wiring The Fault Alarm Contacts

    Wiring the Fault Alarm Contacts The fault alarm contact is in the middle of terminal block connector as the picture shows below. Inserting the wires, it will detect the fault status which the power is failure or port link failure (for managed model) and form an open circuit. Insert the wires into the fault alarm contacts (No.

  • Page 27: Installation

    Installation DIN-Rail Mounting Assembling the DIN-Rail Clip The DIN-rail clip is screwed on the industrial switch when out of factory. If not, please refer to the following steps to secure the DIN-rail clip on the switch. 1. Use the included screws to secure the DIN-rail clip on the industrial switch. 2.
  • Page 28 Hanging the Industrial Switch Follow the steps below to hang the industrial switch on the DIN rail. 1. First, position the rear side of the switch directly in front of the DIN rail. Make sure the top of the clip hooks over the top of the DIN rail. 2.

  • Page 29: Wall Mounting

    Wall Mounting To hang the Ethernet switch on the wall, please follow the steps below. 1. Remove the DIN-rail clip. 2. Prepare the two wall-mount plates and six screws included . 3. Align the screw holes bewteen the wall-mount plates and the unit as the figure illustrated . 4.

  • Page 30: Installation Steps

    Installation Steps 1. Unpack the Industrial switch 2. Check if the DIN-rail clip is screwed on the Industrial switch or not. If the DIN-rail clip is not screwed on the Industrial switch, please refer to the DIN-Rail Mounting section for DIN-rail installation. If users want to wall-mount the Industrial switch, then please refer to Wall-Mount Plate Mounting section for wall-mount plate installation.

  • Page 31: Console Management

    Console Management Connecting to the Console Port One end of the supplied cable is RS-232 connector and the other end is RJ-45 connector. Attach the RS-232 connector to PC or terminal and the RJ-45 connector to the console port of the switch. The connected terminal or PC must support the terminal emulation program.

  • Page 32: Login In The Console Interface

    Login in the Console Interface When the connection between Switch and PC is ready, turn on the PC and run a terminal emulation program or Hyper Terminal and configure its communication parameters to match the following default characteristics of the console port: Baud Rate: 9600 bps Data Bits: 8 Parity: none...

  • Page 33: Cli Management

    Console login interface CLI Management The system supports the console management – CLI command. After you log in on to the system, you will see a command prompt. To enter CLI management interface, type in “enable” command. CLI command interface...

  • Page 34: Commands Level

    The following table lists the CLI commands and description. Commands Level Access Exit Modes Prompt About This Mode Method Method The user commands available at the user level are a subset of Begin a Enter those available at the User EXEC session with switch>...

  • Page 35: Commands Set List

    privileged EXEC mode. Enter the To exit to interface of global fast Ethernet configuratio command n mode, Use this mode to switch Interface (with a enter exit. configure parameters configuration specific (config-if)# To exit to for the switch and Ethernet ports. interface) privileged while in global...
  • Page 36 [System Name] name system location Set switch system switch(config)#system location [System Location] location string system description Set switch system switch(config)#system [System Description] description string description xxx system contact Set switch system switch(config)#system contact [System Contact] contact window string show system-info Show system switch>show system-info information...
  • Page 37 dhcpserver subnetmask Configure subnet switch(config)#dhcpserver [Subnet mask] mask for DHCP clients subnetmask 255.255.255.0 dhcpserver gateway Configure gateway for switch(config)#dhcpserver [Gateway] DHCP clients gateway 192.168.1.254 dhcpserver dnsip Configure DNS IP for switch(config)#dhcpserver dnsip [DNS IP] DHCP clients 192.168.1.1 dhcpserver leasetime Configure lease time switch(config)#dhcpserver [Hours] (in hour)

  • Page 38: Port Commands Set

    function no security http Disable IP security of switch(config)#no security http HTTP server no security telnet Disable IP security of switch(config)#no security telnet telnet server Port Commands Set Commands Level Description Example interface fastEthernet Choose the port for switch(config)#interface [Portid] modification.
  • Page 39 switch(config-if)#no security bandwidth type all Set interface ingress switch(config)#interface limit frame type to fastEthernet 2 “accept all frame” switch(config-if)#bandwidth type bandwidth type Set interface ingress switch(config)#interface limit frame type to fastEthernet 2 broadcast-multicast- flooded-unicast “accept broadcast, switch(config-if)#bandwidth type multicast, and flooded broadcast-multicast-flooded- unicast frame”...

  • Page 40: Trunk Commands Set

    limit. show bandwidth Show interfaces switch(config)#interface bandwidth control fastEthernet 2 switch(config-if)#show bandwidth state Use the state interface switch(config)#interface [Enable | Disable] configuration fastEthernet 2 command to specify (config-if)#state Disable the state mode of operation for Ethernet ports. Use the disable form of this command to disable the port.
  • Page 41 [Group ID] activityport 2 [Port Numbers] aggregator group Assign a trunk group switch(config)#aggregator group [GroupID] [Port-list] 1 1-4 lacp workp 2 with LACP active. lacp workp [GroupID] :1~3 [Workport] switch(config)#aggregator group [Port-list]:Member port list, This parameter 2 1,4,3 lacp workp 3 could be a port range(ex.1-4) or a port list separate by a...

  • Page 42: Vlan Commands Set

    no aggregator group Remove a trunk group switch(config)#no aggreator [GroupID] group 2 VLAN Commands Set Commands Level Description Example vlan database Enter VLAN configure switch#vlan database mode Vlanmode To set switch VLAN switch(vlan)#vlanmode portbase [portbase| 802.1q | mode. gvrp] switch(vlan)#vlanmode 802.1q switch(vlan)#vlanmode gvrp no vlan No VLAN...

  • Page 43: Spanning Tree Commands Set

    [UntaggedVID] port belong to a trunk group, this command can’t be applied. Assign a trunk link for switch(vlan)#vlan 8021q port 3 vlan 8021q port [PortNumber] VLAN by port, if the trunk-link tag 2,3,6,99 trunk-link tag port belong to a trunk [TaggedVID List] group, this command switch(vlan)#vlan 8021q port 3...
  • Page 44 spanning-tree enable Enable spanning tree switch(config)#spanning-tree enable spanning-tree priority Configure spanning switch(config)#spanning-tree [0~61440] tree priority parameter priority 32767 spanning-tree max-age Use the spanning-tree switch(config)#spanning-tree [seconds] max-age global max-age 15 configuration command to change the interval between messages the spanning tree receives from the root switch.
  • Page 45 forwarding-time for the specified spanning- tree instances. The forwarding time determines how long each of the listening learning states last before the port begins forwarding. stp-path-cost Use the spanning-tree switch(config)#interface [1~200000000] cost interface fastEthernet 2 configuration switch(config-if)#stp-path-cost 20 command to set the path cost for Spanning Tree Protocol (STP)

  • Page 46: Qos Commands Set

    stp-admin-p2p Admin P2P of STP switch(config)#interface [Auto|True|False] priority on this fastEthernet 2 interface. switch(config-if)#stp-admin-p2p Auto stp-admin-edge Admin Edge of STP switch(config)#interface [True|False] priority on this fastEthernet 2 interface. switch(config-if)#stp-admin-edge True stp-admin-non-stp Admin NonSTP of switch(config)#interface [True|False] STP priority on this fastEthernet 2 interface.

  • Page 47: Igmp Commands Set

    show qos Displays the Switch#show qos information of QoS configuration no qos Disable QoS function switch(config)#no qos IGMP Commands Set Commands Level Description Example igmp enable Enable IGMP switch(config)#igmp enable snooping function Igmp-query auto Set IGMP query to switch(config)#Igmp-query auto auto mode Igmp-query force Set IGMP query to...

  • Page 48: Snmp Commands Set

    [MAC] show mac-address-table Show all MAC address switch#show mac-address-table table show mac-address-table Show static MAC switch#show mac-address-table static address table static show mac-address-table Show filter MAC switch#show mac-address-table filter address table. filter no mac-address-table Remove an entry of switch(config)#interface static hwaddr MAC address table of fastEthernet 2 [MAC]...
  • Page 49 snmp-server host Configure SNMP switch(config)#snmp-server host [IP address] server host 192.168.1.50 community public community information and trap-version v1 [Community-string] community string (remove) trap-version Switch(config)# [v1|v2c] no snmp-server host 192.168.1.50 snmpv3 context-name Configure the context switch(config)#snmpv3 context- name [Context Name ] name Test snmpv3 user Configure the...
  • Page 50 [Excluded|Included] sub-oid [OID] show snmp Show SNMP switch#show snmp configuration no snmp community- Remove the specified switch(config)#no snmp community. strings [Community] community-strings public no snmp-server host Remove the SNMP switch(config)#no snmp-server [Host-address] server host. 192.168.1.50 no snmpv3 user Remove specified switch(config)#no snmpv3 user [User Name] user of SNMPv3...

  • Page 51: Port Mirroring Commands Set

    Port Mirroring Commands Set Commands Level Description Example monitor Configure source port switch(config)#interface [RX|TX|Both] of monitor function fastEthernet 2 switch(config-if)#monitor RX monitor rx [Port ID] Set RX destination switch(config)#monitor rx 2 port of monitor function monitor tx [Port ID] Set TX destination switch(config)#monitor tx 3 port of monitor function...
  • Page 52 8021x system serverport Use the 802.1x switch(config)# 8021x system [port ID] system server port serverport 1815 global configuration command to change the radius server port 8021x system Use the 802.1x switch(config)# 8021x system accountport system account port accountport 1816 [port ID] global configuration command to change the accounting port...

  • Page 53: Tftp Commands Set

    configuration command to set the supplicant timeout. 8021x misc Use the 802.1x misc switch(config)#8021x misc servertimeout [sec.] server timeout global servertimeout 20 configuration command to set the server timeout. 8021x misc maxrequest Use the 802.1x misc switch(config)# 8021x misc [number] max request global maxrequest 3 configuration...

  • Page 54: Systemlog, Smtp And Event Commands Set

    backup Save configuration to switch(config)#backup flash:backup_cfg TFTP and need to flash:backup_cfg specify the IP of TFTP server and the file name of image. restore Get configuration from switch(config)#restore flash:restore_cfg TFTP server and need to flash:restore_cfg specify the IP of TFTP server and the file name of image.
  • Page 55 smtp account Configure switch(config)#smtp account [account] authentication account John smtp password Configure switch(config)#smtp password [password] 1234 authentication password smtp rcptemail Configure Rcpt e-mail switch(config)#smtp rcptemail 1 Address [Index] [Email address] Alert@test.com show smtp Show the information switch#show smtp of SMTP no smtp Disable SMTP switch(config)#no smtp...

  • Page 56: Sntp Commands Set

    event type no event systemlog Disable port event for switch(config)#interface system log fastethernet 3 switch(config-if)#no event systemlog no event smpt Disable port event for switch(config)#interface SMTP fastethernet 3 switch(config-if)#no event smtp show systemlog Show system log switch#show systemlog client & server information SNTP Commands Set Commands...

  • Page 57: X-Ring Commands Set

    sntp ip Set SNTP server IP, if switch(config)#sntp ip 192.169.1.1 [IP] SNTP function is inactive, this command can’t be applied. sntp timezone Set timezone index, switch(config)#sntp timezone 22 [Timezone] use “show sntp timzezone” command to get more information of index number show sntp Show SNTP...
  • Page 58 ring homingport Configure Dual switch(config)#ring homingport 3 [Dual Homing Port] Homing Port show ring Show the information switch#show ring of X - Ring no ring Disable X-ring switch(config)#no ring no ring master Disable ring master switch(config)# no ring master no ring couplering Disable couple ring switch(config)# no ring couplering...

  • Page 59: Web-Based Management

    Web-Based Management This section introduces the configuration and functions of the Web-Based management. About Web-based Management There is an embedded HTML web site residing in flash memory on CPU board of the switch, which offers advanced management features and allows users to manage the switch from anywhere on the network through a standard browser such as Microsoft Internet Explorer.

  • Page 60: System Login

    System Login Launch the Internet Explorer on the PC Key in “http:// “+” the IP address of the switch”, and then Press “Enter”. The login screen will appear right after Key in the user name and password. The default user name and password are the same as ‘root’...

  • Page 61: System Information

    System Information Assign the system name and location and view the system information System Name: Assign the system name of the switch (The maximum length is 64 bytes) System Description: Describes the switch. System Location: Assign the switch physical location (The maximum length is 64 bytes).

  • Page 62: Dhcp Server - System Configuration

    is to inform the user that when the DHCP client is enabled, the current IP will lose and user should find the new IP on the DHCP server. IP Address: Assign the IP address that the network is using. If DHCP client function is enabled, and then the user doesn’t need to assign the IP address.
  • Page 63 network administration because the software keeps track of IP addresses rather than requiring an administrator to manage the task. This means that a new computer can be added to a network without the hassle of manually assigning it a unique IP address. The system provides the DHCP server function.

  • Page 64: Dhcp Server - Client Entries

    DHCP Server – Client Entries When the DHCP server function is active, the system will collect the DHCP client information and displays it at this tab. DHCP Client Entries interface DHCP Server - Port and IP Bindings Assign the dynamic IP address to the port. When the device is connecting to the port and asks for IP assigning, the system will assign the IP address that has been assigned before to the connected device.

  • Page 65: Tftp - Update Firmware

    Port and IP Bindings interface TFTP - Update Firmware It provides the functions that allow user to update the switch firmware. Before updating, make sure the TFTP server is ready and the firmware image is located on the TFTP server. TFTP Server IP Address: Type in your TFTP server IP.

  • Page 66: Tftp - Restore Configuration

    Update Firmware interface TFTP – Restore Configuration You can restore the configuration from TFTP server. Before doing that, you must put the image file on TFTP server first and the switch will download back the flash image. TFTP Server IP Address: Type in the TFTP server IP. Restore File Name: Type in the correct file name for restoring.

  • Page 67: System Event Log - Syslog Configuration

    Backup Configuration interface System Event Log – Syslog Configuration Configure the system event mode to collect system log. Syslog Client Mode: Select the system log mode—Client Only, Server Only, or Both. System Log Server IP Address: Assign the system log server IP. When Syslog Client Mode is set as Client Only, the system event log will only be sent to the client which has logged in on the switch.

  • Page 68: System Event Log - Smtp Configuration

    Syslog Configuration interface System Event Log - SMTP Configuration You can set up the mail server IP, mail account, password, and forwarded email account for receiving the event alert. Email Alert: Enable or disable the email alert function. SMTP Server IP: Set up the mail server IP address (when Email Alert enabled, this function will then be available).

  • Page 69: System Event Log - Event Configuration

    will then be available). Mail Account: Set up the email account, e.g. johnadmin, to receive the alert. It must be an existing email account on the mail server, which you had set up in SMTP Server IP Address column. Password: Type in the password to the email account. Confirm Password: Reconfirm the password.
  • Page 70 server/SMTP server. Also, per port log (link up, link down, and both) events can be sent to the system log server/SMTP server with the respective checkbox ticked. After configuring, click to have the setting taken effect. Apply System event selection: There are 4 event types—Device cold start, Device warm start, Authentication Failure, and X-ring topology change.
  • Page 71 Event Configuration interface...

  • Page 72: Fault Relay Alarm

    Fault Relay Alarm Power Failure: Tick the checkbox to enable the function of lighting up the FAULT LED on the panel when power fails. Port Link Down/Broken: Tick the checkbox to enable the function of lighting up FAULT LED on the panel when Ports’ states are link down or broken. Fault Relay Alarm interface SNTP Configuration You can configure the SNTP (Simple Network Time Protocol) settings.
  • Page 73 Local Time Zone Conversion from UTC Time at 12:00 UTC November Time Zone - 1 hour 11am Oscar Time Zone -2 hours 10 am ADT - Atlantic Daylight -3 hours 9 am AST - Atlantic Standard -4 hours 8 am EDT - Eastern Daylight EST - Eastern Standard -5 hours...
  • Page 74 BT - Baghdad, USSR +3 hours 3 pm Zone 2 ZP4 - USSR Zone 3 +4 hours 4 pm ZP5 - USSR Zone 4 +5 hours 5 pm ZP6 - USSR Zone 5 +6 hours 6 pm WAST - West Australian +7 hours 7 pm Standard...

  • Page 75: Ip Security

    SNTP Configuration interface IP Security IP security function allows the user to assign 10 specific IP addresses that have permission to access the switch through the web browser for the securing switch management. IP Security Mode: When this option is in Enable mode, the Enable HTTP Server and Enable Telnet Server checkboxes will then be available.

  • Page 76: User Authentication

    IP Security interface User Authentication Change web management login user name and password for the management security issue. User name: Type in the new user name (The default is ‘root’) Password: Type in the new password (The default is ‘root’) Confirm password: Re-type the new password And then, click Apply...

  • Page 77: Port Statistics

    Port Statistics The following information provides the current port statistic information. Port: Displays the port number. Type: Displays the media type of the port. Link: The status of linking—‘Up’ or ‘Down’. State: The user can set the state of the port as ‘Enable’ or ‘Disable’ via Port Control. When the state is disabled, the port will not transmit or receive any packet.

  • Page 78: Port Control

    Port Statistics interface Port Control In Port control, you can view and set the operation mode of each port. Port: Select the port that you want to configure. State: Current port status. The port can be set to disable or enable mode. If the port state is set as ‘Disable’, it will not receive or transmit any packet.

  • Page 79: Port Trunk

    specified period of time. When disabled, the receiving device will drop the packet if too much to process. Security: Once the Security selection is set as ‘On’, any access from the device which connects to this port will be blocked unless the MAC address of the device is included in the static MAC address table.

  • Page 80: Aggregator Setting

    exchanging information between Partner Systems on a link to allow their Link Aggregation Control instances to reach agreement on the identity of the Link Aggregation Group to which the link belongs, move the link to that Link Aggregation Group, and enable its transmission and reception functions in an orderly manner. Link aggregation lets you group up to 4 ports into one dedicated connections.

  • Page 81: Aggregator Information

    Click Apply button. Delete button to delete Trunk Group. Select the Group ID and click Delete button. Port Trunk—Aggregator Setting interface (four ports are added to the left field with LACP enabled) Aggregator Information When you have setup the aggregator setting with LACP disabled, you will see the local static trunk group information in here.

  • Page 82: State Activity

    Port Trunk—Aggregator Setting interface (two ports are added to the left field with LACP disable) Port Trunk – Aggregator Information interface State Activity Having set up the LACP aggregator on the tab of Aggregator Setting, you can configure the state activity for the members of the LACP trunk group. You can tick or cancel the checkbox beside the state display.

  • Page 83: Port Mirroring

    Port Trunk – State Activity interface Port Mirroring The Port mirroring is a method for monitoring traffic in switched networks. Traffic through ports can be monitored by one specific port which means traffic goes in or out monitored (source) ports will be duplicated into mirroring (destination) port.
  • Page 84 Port Trunk – Port Mirroring interface Destination Port: There is only one port can be selected to be the destination (mirroring) port for monitoring both RX and TX traffic which come from the source port. Or, use one of two ports for monitoring RX traffic only and the other one for TX traffic only.

  • Page 85: Rate Limiting

    Rate Limiting You can set up every port’s frame limitation type and bandwidth rate. Rate Limiting interface Ingress Limit Frame type: Select the frame type you want to filter. The frame types have 4 options for selecting: All, Broadcast/Multicast/Flooded Unicast, Broadcast/Multicast, and Broadcast only.
  • Page 86 1 is 10Mbps; the user can set the effective egress rate of port 1 as 1Mbps, ingress rate 500Kbps. The switch performs the ingress rate by packet counter to meet the specified rate. » Ingress: Enter the port effective ingress rate (The default value is “0”). »...

  • Page 87: Vlan Configuration

    VLAN configuration A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain, which would allow you to isolate network traffic, so only the members of the same VLAN will receive traffic from the ones of the same VLAN. Basically, creating a VLAN from a switch is logically equivalent of reconnecting a group of network devices to another Layer 2 switch.
  • Page 88 on not only default PVID but also other information about the packet, such as the protocol. VLAN – Port Based interface Pull down the selection item and focus on Port Based then press Apply button to set the VLAN Operation Mode in Port Based mode. Click button to add a new VLAN group (The maximum VLAN group is up to 64 VLAN groups).
  • Page 89 VLAN—Port Based Add interface Enter the group name and VLAN ID. Add the port number having selected into the right field to group these members to be a VLAN group or remove any of them listed in the right field from the VLAN. And then, click button to have the settings taken effect.
  • Page 90 VLAN—Port Based Edit/Delete interface Delete button to delete the VLAN. button to modify group name, VLAN ID, or add/remove the members of Edit the existing VLAN group. [NOTE] Remember to execute the “Save Configuration” action, otherwise the new configuration will lose when switch power off.

  • Page 91: 802.1Q Vlan

    802.1Q VLAN Tagged-based VLAN is an IEEE 802.1Q specification standard. Therefore, it is possible to create a VLAN across devices from different switch venders. IEEE 802.1Q VLAN uses a technique to insert a “tag” into the Ethernet frames. Tag contains a VLAN Identifier (VID) that indicates the VLAN numbers.
  • Page 92 » Access Link: Single switch only, it allows the user to group ports by assigning the same Untagged VID. While this link type is set, the Untagged VID column field is available but the Tagged VID column field is disabled. »...
  • Page 93 802.1Q VLAN interface Group Configuration Edit the existing VLAN Group. Select the VLAN group in the table list. Click button. Edit...
  • Page 94 Group Configuration interface You can modify the VLAN group name and VLAN ID. Group Configuration interface Click button. Apply...

  • Page 95: Rapid Spanning Tree

    Rapid Spanning Tree The Rapid Spanning Tree Protocol (RSTP) is an evolution of the Spanning Tree Protocol and provides for faster spanning tree convergence after a topology change. The system also supports STP and the system will auto-detect the connected device that is running STP or RSTP protocol.

  • Page 96: Rstp - Port Configuration

    RSTP System Configuration interface RSTP - Port Configuration You can configure path cost and priority of every port. Select the port in the port column field. Path Cost: The cost of the path to the other bridge from this transmitting bridge at the specified port.
  • Page 97 Admin Edge: The port directly connected to end stations won’t create bridging loop in the network. To configure the port as an edge port, set the port to “True” status. Admin Non Stp: The port includes the STP mathematic calculation. True is not including STP mathematic calculation.

  • Page 98: Snmp Configuration

    SNMP Configuration Simple Network Management Protocol (SNMP) is the protocol developed to manage nodes (servers, workstations, routers, switches and hubs etc.) on an IP network. SNMP enables network administrators to manage network performance, find and solve network problems, and plan for network growth. Network management systems learn of problems by receiving traps or change notices from network devices implementing SNMP.

  • Page 99: Trap Configuration

    SNMP System Configuration interface Trap Configuration A trap manager is a management station that receives the trap messages generated by the switch. If no trap manager is defined, no traps will be issued. Create a trap manager by entering the IP address of the station and a community string. To define a management station as a trap manager, assign an IP address, enter the SNMP community strings, and select the SNMP trap version.

  • Page 100: Snmpv3 Configuration

    Trap Managers interface SNMPV3 Configuration Configure the SNMP V3 function. Context Table Configure SNMP v3 context table. Assign the context name of context table. Click to add context name. Click Remove to remove the unwanted context name. User Profile Configure SNMP v3 user table.. User ID: Set up the user name.
  • Page 101 SNMP V3 configuration interface Group Table Configure SNMP v3 group table.
  • Page 102 Security Name (User ID): Assign the user name that you have set up in user table. Group Name: Set up the group name. Click to add the context name. Click to remove the unwanted context name. Remove Access Table Configure SNMP v3 access table. Context Prefix: Set up the context name.

  • Page 103: Qos Configuration

    QoS Configuration Here you can configure Qos policy and priority setting, per port priority setting, COS and TOS setting. QoS Policy and Priority Type Qos Policy: Select the QoS policy rule. » Using the 8,4,2,1 weight fair queue scheme: The switch will follow 8:4:2:1 rate to process priority queue from High to lowest queue.

  • Page 104: Port-Based Priority

    QoS Configuration interface Port-based Priority Configure the priority level for each port. With the drop-down selection item of Priority Type above being selected as Port-based, this control item will then be available to set...

  • Page 105: Cos Configuration

    the queuing policy for each port. Port x: Each port has 4 priority levels—High, Middle, Low, and Lowest—to be chosen. Click Apply button to make the settings effective. COS Configuration Set up the COS priority level. With the drop-down selection item of Priority Type above being selected as COS only/COS first, this control item will then be available to set the queuing policy for each port.

  • Page 106: Igmp Configuration

    IGMP Configuration The Internet Group Management Protocol (IGMP) is an internal protocol of the Internet Protocol (IP) suite. IP manages multicast traffic by using switches, routers, and hosts that support IGMP. Enabling IGMP allows the ports to detect IGMP queries, report packets, and manage IP multicast traffic through the switch.

  • Page 107: X-Ring

    IGMP Configuration interface X-Ring X-Ring provides a faster redundant recovery than Spanning Tree topology. The action is similar to STP or RSTP, but the algorithms are different. In the X-Ring topology, every switch should enable X-Ring function and assign two member ports for connecting to the ring.
  • Page 108 The system also supports the coupling ring that can connect 2 or more X-Ring group for the redundant backup function and dual homing function that prevent connection lose between X-Ring group and upper level/core switch. Enable X-Ring: To enable the X-Ring function. Marking the check box to enable the X-Ring function.
  • Page 109 X-ring Interface Note When the X-Ring function enable, user must disable the RSTP. The X-Ring function and RSTP function cannot exist in a switch at the same time. Remember to execute the ‘Save Configuration’ action, otherwise the new configuration will lose when switch power off.

  • Page 110: Security

    Security In this section, you can configure the 802.1x and MAC address table. 802.1X/Radius Configuration 802.1x is an IEEE authentication specification which prevents the client from connecting to a wireless access point or wired switch until it provides authority, like the user name and password that are verified by an authentication server (such as RADIUS server).
  • Page 111 802.1x System Configuration interface 802.1x Per Port Configuration You can configure the 802.1x authentication state for each port. The state provides Disable, Accept, Reject, and Authorize. Reject: The specified port is required to be held in the unauthorized state. Accept: The specified port is required to be held in the Authorized state. Authorized: The specified port is set to the Authorized or Unauthorized state in accordance with the outcome of an authentication exchange between the Supplicant and the authentication server.
  • Page 112 802.1x Per Port Setting interface Misc Configuration Quiet Period: Set the period which the port doesn’t try to acquire a supplicant. TX Period: Set the period the port waits for retransmit next EAPOL PDU during an authentication session. Supplicant Timeout: Set the period of time the switch waits for a supplicant response to an EAP request.

  • Page 113: Mac Address Table

    Reauth period: Set the period of time which clients connected must be re- authenticated. Click Apply button. 802.1x Misc Configuration interface MAC Address Table Use the MAC address table to ensure the port security. Static MAC Address You can add a static MAC address; it remains in the switch's address table, regardless of whether the device is physically connected to the switch.
  • Page 114 Port No.: Pull down the selection menu to select the port number. Click button. If you want to delete the MAC address from filtering table, select the MAC address and click Delete button. Static MAC Addresses interface MAC Filtering By filtering MAC address, the switch can easily filter the pre-configured MAC address and reduce the un-safety.
  • Page 115 MAC Filtering interface MAC Address: Enter the MAC address that you want to filter. Click button. If you want to delete the MAC address from the filtering table, select the MAC address and click button. Delete All MAC Addresses You can view the port that connected device’s MAC address and the related devices’ MAC address.

  • Page 116: Factory Default

    All MAC Address interface Factory Default Reset switch to default configuration. Click button to reset all configurations to Reset the default value. Factory Default interface Save Configuration Save all configurations that you have made in the system. To ensure the all...

  • Page 117: System Reboot

    configuration will be saved. Click to save the all configuration to the flash Save memory. Save Configuration interface System Reboot Reboot the switch in software reset. Click to reboot the system. Reboot System Reboot interface...

  • Page 118: Troubleshooting

    Troubleshooting Verify that you are using the correct power cord/adapter. Don’t use the power adapter with DC output higher than the power ratings of the equipment. Select the proper UTP/STP cable to construct the user network. Use unshielded twisted-pair (UTP) or shield twisted-pair (STP) cable for RJ-45 connections: 100Ω Category 3, 4 or 5 cable for 10Mbps connections, 100Ω...

  • Page 119: Technical Specifications

    Technical Specifications IEEE 802.3 10Base-T IEEE 802.3u 100Base-TX IEEE 802.3ab 1000Base-T IEEE 802.3z Gigabit fiber IEEE 802.3x Flow Control and Back-pressure IEEE 802.3ad Port trunk with LACP Standard IEEE 802.1d Spanning Tree IEEE 802.1w Rapid Spanning Tree IEEE 802.1p Class of Service IEEE 802.1Q VLAN Tag IEEE 802.1x User Authentication (RADIUS) IEEE 802.1ab LLDP**...
  • Page 120 EIA/TIA-568 100-ohm (100m) 1000Base-T: 2-pair UTP/STP Cat. 5e or 6 cable EIA/TIA-568 100-ohm (100m) „ LC (Multi-mode): 50/125um or 62.5/125um Optical Cable „ LC (Single-mode): 9/125um Back-plane 7.2Gbps Packet Throughput 10.7Mpps at 64bytes Ability 12 ~ 48 V Power Supply Redundant power with polarity reverse protection and removable terminal block Power Consumption...
  • Page 121 CE EN61000-4-5 (Surge) CE EN61000-4-6 (CS) CE EN61000-4-8 CE EN61000-6-2 CE EN61000-6-4 Safety CE/EN60950-1 Class I/ Division 2 IEC60068-2-32 (Free fall) Stability Testing IEC60068-2-27 (Shock) IEC60068-2-6 (Vibration)

Table of Contents