Advertisement
(5
Reglstering the lndoor Unlt Wlth the Remote Controller )
(lnltlal reglstratlon mode operatlon)
Ап lпdoor uпit
must
Ье
reglstered wlth the remote
coпtroller lп а
group
arraпgemeпt
or
а
system where
dlffereпt refrlgeraпts
are used. Reglster
ап lпdoor uпlt us/пg
the
lпltlal reglstratloп
mode as
showп
below.
lп addltioп,
the
lпltlal reg/stratloп
mode
сап Ье
used to search for
ап lпdoor
unlt
reglstered to the group or to delete
а reglstratloп.
Thls remote
coпtroller саппоt Ье
used to perform
ап lпterlocklпg reglstratloп
of
lпterlocked uпlts.
The
ceпtral coпtroller
(MJ-103MTRA) or
пetwork
remote
coпtroller
(PAR-F25MA) must
Ье
used to make
lпterlocklпg reglstratloпs.
Settlng Procedure
Q)
Turп
off the
uпlt.
(Perform the
followlпg operatloп
after
"НО"
flashes
оп
the dlsplay.)
®
Hold
dowп
both
ТЕМР.
Ci::>
апd СУ::>
for more
thaп
2
secoпds.
Thls starts the
lпitlal registratloп
mode
апd
the set remote
coпtrol
ler address flashes
оп
the dlsplay.
' ' 1 / /
-
/П
/
_. IU
~' ""==~------
/
/ \
®
Press
ТЕМР. ~
to select the address of the
lпdoor uпlt
that you wlsh to register wlth thls remote
coпtroller.
After the
butloп
is pressed
опсе,
the remote
coпtroller
ad-
dress,
апd theп
the
lпdoor uпit
address ls dlsplayed. After-
wards, each press of the butlon
lпcreases
the
lпdoor
unlt
address
Ьу
1 as
showп
below.
Holdlпg
down the
buttoп
chaпges
the address more qulckly.
[101)
-+ [- - -]
-+
[001]
-+
[002)
-+
(Set remote controller address)
Flashes
-+
[049]
-+
[050]
@
Wheп
the address of the
iпdoor uпlt
that you wlsh to reglster
ls dlsplayed, press
~
to
beglп reglsterlпg.
lf the
reglstratloп
ls completed correctly, the dlsplay appears
as
showп
below.
пп
ии
IГ
IL
The lndoor unlt type, "IC",
ls dlsplayei:t.
lf the
reglstratloп
ls not completed correctly, "88" flashes ln
the dlsplay. Check that the selected lndoor unlt address or
the wirlng are correct.
Up to 16 lndoor
uпlts
can
Ье
reglstered.
®
After reglsterlng, hold
dowп
both
ТЕМР. ~
and
СУ::>
for
more
thaп
2
secoпds
to
епd
the lnltial reglstratlon mode and
the normal dlsplay appears.
NOTE:
• Up to 16 lndoor
uпlts сап Ье
reglstered.
Conflrmatlon of reglstered address
®
Dlsplay the addresses of the
lпdoor uпlts
that are reglstered
wlth thls remote controller.
Each press of
ТЕМР. СУ::> lп
step
®
or @ dlsplays the ad-
dress of
а
reglstered Jndoor unlt
апd
lts type, "IC".
lf no lndoor
uпlt
ls reglstered, "- - -" appears ln the address
dlsplay
апd по
type ls dlsplayed.
Address delectlon
(j)
Delete the address of
ап
lndoor unlt reglstered wlth thls re-
mote controller.
Hold down [ON/OFF] twlce for 2 seconds each tlme elther ln
step @ or after the reglstratlon ls complete to delete the regis-
tratloп
of the lndoor unlt that ls
curreпtly
dlsp/ayed.
пп
/
ии
1
When the dlsplay appears as
showп
above, hold down [ON/
OFF] twlce for 2
secoпds
each tlme.
J,
ии
/
[ nn. /
lf the reglstratlon ls deleted correctly, "- - " appears
lп
the
dlsplay.
lf the reglstratlon ls not deleted correctly, "88" flashes in the
dlsplay. Check that the selected lndoor unlt address and the
wlring are correct.
• lf the
reglstratloп
cannot
Ье
completed or deleted correctly, elther the set address or the wlrlng of the lndoor unlt whose
reglstratlon you wlsh to add or delete may
Ье
lncorrect. Check the wlrlng and the address that ls set.
( 6
Operatlng Durlng the Test Run )
1 .
How to Use the Test Run
The test run
свпnоt Ье
started uslng thls remote controller. Use the network or group remote controller to start the test run. During
а
test
run, thls remote controller appears as shown below. After two hours, the test run stops automat/cally.
2.
Press [ON/OFF] durlng the test run to
сапсеl
lt and turn off the
uпlt.
The room temperature cannot
Ье
set
durlпg а
test
ruп;
only the alr
speed
сап Ье
adJusted.
lndoor unlt address of the dlsolaved
оlов
temoerature
The address of the lndoor unlt reglsterad wlth thls remote controller ls dlsplayed. lf
more than one lndoor unlt ls reglstered, the addresses of the other unlts oan
Ье
dls-
played
Ьу
presslng
ТЕМР. ~-
Dlsplay range: 001 to 050
DJ
C'·S
0
~п Т
lndoor unlt plpe temperature
1
The plpe temperature of the lndoor unlt address shown ls dlsplayed.
1
,._-'
/
-
си·с
Q
-"
·~·
Dlsplay range:
-99°С
to
99°с
lf the temperature exceeds thls range,
"-99°С"
or
"99°С"
f\ashes on the dlsplay.
@
Remalnlng tlme of the test run
The amount of tlme remalnlng for the test run ls dlsplayed.
Dlsplay range: 2:00 to 0:01
Thls product ls deslgned and
lnteпded
for use ln
а
resldentlal, commerclal or llght-lndustrlal envlronment.
The product at hand ls based on the follow/ng EU regulatlons:
Low Voltage Defectlve
73/23/ЕЕС
Electromagпetlc
Compatlbllity Dlrectlve
89/336/ЕЕС
~
MITSUBISHI ELECTRIC CORPORATION
Advertisement
