Philips FastCare GC7700 series Quick Start Manual

GC7700_HULK_4239.001.0130.1_AUS_cHR.pdf 1 03-11-15 10:46
Issue related to Problem
The appliance has
function was activated.
This happens automatically
when the steam generator
has not been used or the
steam trigger has not been
pressed for more than
15 minutes.
The appliance produces The water tank is empty.
a loud pumping sound.
Dirty water and impurities After the Calc-Clean
come out of the soleplate. process, remaining water
may drip out of the
soleplate.
The Calc-Clean process
has not been completed.
Impurities or chemicals
present in the water have
deposited in the steam
vents and/or soleplate.
You have accidentally
soleplate. started the Calc-Clean
process. See chapter 4
Calc-Clean.
The Calc-Clean process You have not set the
does not start. temperature dial to CALC
CLEAN, you have not
waited for the iron to heat
up or you have not pressed
the Calc-Clean button
for 2 seconds until the
appliance started beeping.
There are water droplets Water comes from the
visible in the appliance water path between the
when I detach the water tank and stand. This
water tank. is normal.
Steam output is low. You did not press the
steam trigger continuously.
Solution
again.
Fill the water tank with water and press the steam
trigger until the pumping sound becomes softer
and steam comes out of the soleplate.
Wipe the soleplate dry with a piece of cloth.
appliance still beeps, perform the Calc-Clean
process. See chapter 4 Calc-Clean.
You have to perform the Calc-Clean process
again. See chapter 4 Calc-Clean.
Perform the Calc-Clean process regularly.
See chapter 4 Calc-Clean.
again. Turn the temperature dial to the desired
temperature setting instead of CÁLC CLEAN.
Let the iron heat up until the 'iron ready' light
lights up steadily.
See chapter 4 Calc-Clean.
These water droplets are harmless. If you want,
you can wipe away the water droplets with a dry
cloth.
Keep the steam trigger pressed continuously
when you move the iron over the fabric.
4239.001.0130.1
Quick Start Guide
FastCare GC7700 series
Congratulations on the purchase of your Philips
Product support
FastCare steam generator iron! It has a large
output and a smooth SteamGlide Ceramic soleplate that reduces
ironing time. The carry lock and Smart CalcClean also make ironing
1
more convenient.
Start
1 2
Press the water tank Remove the water tank
release button. from the base.
X
Use only tap water Do not use the following types of water as they may cause
or demineralised leaking, brown staining and damage to your appliance:
water perfumed water, vinegar, descaling agents, ironing aids etc
Temperature setting Automatic steam setting
•
2
Use
••
•••
to LINEN
1 2
Check the fabric label. Set the temperature dial
to the recommended
temperature.
3
Extra features
2x
For a steam boost, Press the steam trigger
double press the trigger and move the iron up
in quick succession. and down the garment.
Any questions? Don't go back to the store,
Philips is here to help. Contact us directly.
Call: 1300 363 391
www.philips.com/support
3 4
Fill the water tank up to Push the water tank back
the MAX indication. until you hear a click.
Fabric type
Steam ironing is only
Synthetic fabrics (e.g., acetate, acrylic,
nylon, polyamide).
possible at silk, cotton,
Wool, viscose, polyester and silk.
and linen settings.
Cotton, linen.
3 4
Press and hold the Keep the steam trigger
steam trigger to release pressed when you move
steam for ironing. the iron over the fabric.
To save energy, the steam generator switches
15 minutes.
then switch on again.
Call: 0800 658 224