Jinergy JNMP60 series Installation Manual
Crystalline photovoltaic modules
Hide thumbs
Also See for JNMP60 series:
- Installation and maintenance manual (24 pages) ,
- Installation manual (26 pages)
Table of Contents
Advertisement
Quick Links
Crystalline Silicon PV Module
Installation Guide (JET)
JINNENG CLEAN ENERGY TECHNOLOGY LTD
Add: No.1 Wenshui Economic Development Zone, Lvliang, Shanxi 032100, China
Tel: +86(358)3300916
E-mail: sales@jinergy.com
www.jinergy.com
THE FINAL RIGHT OF INTERPRETATION SHALL BE BORNE BY JINERGY. 20171116-D
Advertisement
Table of Contents
Related Manuals for Jinergy JNMP60 series
Summary of Contents for Jinergy JNMP60 series
- Page 1 Crystalline Silicon PV Module Installation Guide (JET) JINNENG CLEAN ENERGY TECHNOLOGY LTD Add: No.1 Wenshui Economic Development Zone, Lvliang, Shanxi 032100, China Tel: +86(358)3300916 E-mail: sales@jinergy.com www.jinergy.com THE FINAL RIGHT OF INTERPRETATION SHALL BE BORNE BY JINERGY. 20171116-D...
-
Page 2: Table Of Contents
CONTENT Introduction Purpose Limitation of Liability Others Safety General Safety Installation Safety Mechanical Installation Installation Condition Installation Methods Electrical Installation Installation Grounding Maintenance and Disposal Attachment Electricity performance List of manufacturers and types of components... -
Page 3: Introduction
Introduction 2.1.4 Follow all safety precautions of all components used in the system. 2.1.5 Do not shade portions of the PV module surface from the sun for a long period of time. The shaded cell may become hot (hot spot phenomenon), which can result in solder joints Purpose peeling off. -
Page 4: Mechanical Installation
and maximum series overcurrent protective device in the combiner box are recommended for Remark: As for above diagram, the solid red arrows indicate primary bolt positions; dashed green arrows indicate positions where bolts can be added for additional support. reverse current protection when more than three strings are connected in parallel. 2.2.16 The solar modules are recommended to be installed over a fireproof and insulating roof Bolts are inserted as described in the process below (Fig. -
Page 5: Electrical Installation
Each aluminum mounting clamp comes with an M8 bolt, a plain washer, a spring washer, and an M8 nut. To fasten the module: 1. Place the module on the two supporting bars (not provided). The bars should be made with stainless material or treated with an anti-corrosion process (e.g., anodic oxidation treatment). -
Page 6: Grounding 10
5.1 Regularly carry out a visual inspection for dirt, dust, bird dropping, leaves, and other ents of the National Electrical Code (NEC) in Article 690 shall be followed to address these detritus covering the modules. increased outputs. In installations not under the requirements of the NEC, the values of Isc and 5.2 If there is a buildup of dirt or dust on the module surface, wash the module with clean water Voc marked on this module should be multiplied by a factor of 1.25 when determining coonductor and a gentle implement (a sponge). - Page 7 6.1.4 Electrical specifications of JNMM72-xxx (xxx =290-340) Series 6 inch Mono-crystalline 6.1.2 Electrical specifications of JNMP60-xxx (xxx =240-285) Series 6 inch Polycrystalline solar solar modules modules JNMP60- JNMP72- Module Type Module Type Pmax(W) Pmax(W) Vmp(V) 29.67 29.88 29.98 30.25 30.51 30.71 30.80 31.00...
- Page 8 6.1.6 Electrical specifications of JNMP72(5BB)-xxx (xxx =285-340) Series 6 inch Polycrystalline solar modules JNMP72- Module Type Pmax(W) 35.15 35.41 35.68 35.93 36.19 36.43 36.85 37.13 37.32 37.63 37.88 38.08 Vmp(V) 8.11 8.19 8.27 8.35 8.43 8.51 8.55 8.62 8.71 8.77 8.85 8.93 Imp(A)