Download Print this page

Casio 5238 Operation Manual

Hide thumbs

Advertisement

Quick Links

MA1106-EA
The configuration of your watch may differ
somewhat from that shown in the illustration.
Hour hand
Minute hand
Second hand
Day
Day of the week
To set the day
1. Pull the crown out to the first click.
2. Set the day by rotating the crown away from you (in the
direction indicated by the arrow in the illustration).
3. Push the crown back in to the normal position.
• Avoid changing the date setting while the current time is
between 9:00 p.m. and 1:00 a.m.
To set the day of the week
1. Pull the crown out to the first click.
2. Set the day of the week by rotating the crown towards you
(in the direction indicated by the arrow in the illustration).
3. Push the crown back in to the normal position.
• Avoid changing the day of the week setting while the current
time is between 11:00 p.m. and 2:00 a.m.
Using the Stopwatch
Stopwatch minute hand
The stopwatch lets you measure elapsed time up to 59 minutes, 59 seconds.
To measure elapsed time
1. Press A to start the stopwatch.
2. Press A to stop the stopwatch.
• You can resume the measurement operation by pressing A again.
3. Check the elapsed time.
• The example below shows an elapsed time of 2 minutes, 44 seconds.
Stopwatch second hand
[44 seconds]
• Press B to reset the stopwatch.
This will enter the Timekeeping Mode.
Notes:
• Do not try to perform stopwatch operations while the crown is pulled out either to
the first or second click. If you try to press a button, you might accidentally cause
the crown to rotate and change the current time or day setting.
• If the starting positions of the stopwatch minute hand and second hand become
misaligned, use the following procedures to adjust the positions of the hands so
they point to 12 o'clock when the stopwatch is reset.
To adjust the positions of the stopwatch hands
1. Press B to reset the stopwatch, and check the alignment of the stopwatch minute
hand and second hand.
2. Pull out the crown to the second click.
3. Press A to move the stopwatch minute hand and second hand.
4. If the stopwatch minute hand is aligned correctly, proceed to step 5. To return the
minute hand to the 12 o'clock position, press B.
5. After making the adjustments you want, push the crown back in to its normal position.
• Note that pulling the crown out also stops the timekeeping second hand. After
performing the above procedure, you should also adjust the timekeeping setting.
I For a watch with an elapsed time bezel
Rotate the elapsed time bezel to align the
minute hand.
After certain amount of time elapsed, read the graduation on
the elapsed time bezel which the minute hand points to.
The elapsed time is indicated.
• Some water resistant models are equipped with a screw lock
crown.
• With such models, you must unscrew the crown in the
direction noted in the illustration to loosen it before you can
pull it out. Do not pull too forcibly on such crowns.
• Also note that such watches are not water resistant while
their crowns are loosened. Be sure to screw the crowns
back in as far as they will go after making any setting.
Accuracy at normal temperature: ± 20 seconds a month
Display: 3 analog hands (timekeeping hour and minutes, stopwatch seconds),
3 dials (timekeeping seconds, day of the week, stopwatch minutes), day
Stopwatch function: Measuring capacity: 59'59''/Measuring unit: 1 second
Measuring mode: Elapsed time
Battery: One silver oxide battery (Type: SR626SW)
Approximately 2 years on type SR626SW (assuming one stopwatch operation 60 min./day)
Operation Guide 5238
To set the time
1. Pull the crown out to the second
click when the second hand is at
12 o'clock position and the
second hand stops.
First click
2. Set the hands by rotating the
(Setting day and
crown. Rotate the crown to
day of the week)
move the hands clockwise.
Move the minute hand four or
five minutes past the time you
want to set, and then back it up
to the proper setting.
Second click
• Carefully set the time, making
(Setting time)
sure to distinguish between
Crown
AM and PM.
(Normal position)
3. Push the crown back in to the
normal position to restart
timekeeping.
Stopwatch second hand
Stopwatch minute hand
[2 minutes]
mark with the
Elapsed time bezel
Specifications
1

Advertisement

loading