Advertisement
WARRANTY/DISCLAIMER
OMEGA Engineering, Inc. warrants this unit to be free of defects in materials
and workmanship for a period of 61 months from date of purchase. OMEGA
Warranty adds an additional one (1) month grace period to the normal five
(5) year product warranty to cover handling and shipping time. This ensures
that OMEGAÕs customers receive maximum coverage on each product.
If the unit should malfunction, it must be returned to the factory for evaluation.
OMEGAÕs Customer Service Department will issue an Authorized Return (AR)
number immediately upon phone or written request. Upon examination by
OMEGA, if the unit is found to be defective it will be repaired or replaced at no
charge. Omega's WARRANTY does not apply to defects resulting from any
action of the purchaser, including but not limited to mishandling, improper
interfacing, operation outside of design limits, improper repair, or unauthorized
modification. This WARRANTY is VOID if the unit shows evidence of having
been tampered with or shows evidence of being damaged as a result of
excessive corrosion; or current, heat, moisture or vibration; improper
specification; misapplication; misuse or other operating conditions outside of
OMEGAÕs control. Components which wear are not warranted, including but
not limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various
products. However, OMEGA neither assumes responsibility for any
omissions or errors nor assumes liability for any damages that result
from the use if its products in accordance with information provided by
OMEGA, either verbal or written. OMEGA warrants only that the parts
manufactured by it will be as specified and free of defects. OMEGA
MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY
KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF
TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies
of purchaser set forth herein are exclusive and the total liability of
OMEGA with respect to this order, whether based on contract,
warranty, negligence, indemnification, strict liability or otherwise, shall
not exceed the purchase price of the component upon which liability is
based. In no event shall OMEGA be liable for consequential, incidental
or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor
shall it be used: (1) as a ÒBasic ComponentÓ under 10 CFR 21 (NRC), used in
or with any nuclear installation or activity; or (2) in medical applications or
used on humans. Should any Product(s) be used in or with any nuclear
installation or activity, medical application, used on humans, or misused in any
way, OMEGA assumes no responsibility as set forth in our basic WARRANTY
/ DISCLAIMER language, and additionally, purchaser will indemnify OMEGA
and hold OMEGA harmless from any liability or damage whatsoever arising
out of the use of the Product(s) in such a manner.
RETURN REQUESTS / INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service
Department. BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER
MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGAÕS
CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING
DELAYS). The assigned AR number should then be marked on the outside of the
return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper
packaging to prevent breakage in transit.
FOR NON-WARRANTY REPAIRS,
FOR WARRANTY RETURNS, please
have the following information available
consult OMEGA for current repair
BEFORE
charges. Have the following information
available BEFORE contacting OMEGA:
contacting OMEGA:
1. P.O. number under which the
1. P.O. number to cover the COST of
the repair,
product was PURCHASED,
2. Model and serial number of the
2. Model and serial number of product,
product under warranty, and
and
3. Repair instructions and/or specific
3. Repair instructions and/or specific
problems relative to the product.
problems relative to the product.
OMEGAÕs policy is to make running changes, not model changes, whenever an
improvement is possible. This affords our customers the latest in technology and
engineering.
OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2017 OMEGA ENGINEERING, INC. All rights reserved.
This document may not be copied, photocopied, reproduced, translated, or reduced
to any electronic medium or machine-readable form, in whole or in part, without
prior written consent of OMEGA ENGINEERING, INC.
PATENT NOTICE: The ÒMeter Case Bezel DesignÓ is a trademark of
NEWPORT Electronics, Inc., registered in the U.S. USED UNDER LICENSE.
This product is covered by one or more of the following patents: U.S. Pat. No.
Des. 336,895; 5,274,577 / CANADA 2052599; 2052600 / ITALY 1249456;
1250938 / FRANCE BREVET No. 91 12756 / SPAIN 2039150; 2048066 /
UK PATENT No. GB2 249 837; GB2 248 954 / GERMANY DE 41 34398 C2.
OTHER INTERNATIONAL PATENTS PENDING.
MQS1865/0917
12502ML-98 Rev. A
5
To Set the Decimal Point Position:
1.
If it's not already shown, press
MENU until the meter displays:
SETPTS
/T1/T2
/DEV
MENU
RESET
2.
Press
/DEV. The meter
displays:
SETPTS
/T1/T2
/DEV
MENU
RESET
3.
Press
/T1/T2/
to move the
decimal point to the desired
location. Choices are FFFF.
and FFF.F.
SETPTS
/T1/T2
/DEV
MENU
RESET
4.
Press MENU to select the decimal point position
shown. The meter displays:
SETPTS
/T1/T2
/DEV
MENU
RESET
SETPTS
/T1/T2
/DEV
MENU
RESET
To Select the Temperature Unit
(Fahrenheit or Celsius):
1.
If it's not already shown, press
MENU until the meter displays:
SETPTS
/T1/T2
/DEV
MENU
RESET
2.
Press
/DEV. The meter
displays:
SETPTS
/T1/T2
/DEV
MENU
RESET
3.
Press
/T1/T2/
to display the
setting you want. Choices are
F and C.
SETPTS
/T1/T2
/DEV
MENU
RESET
4.
Press MENU to select the temperature unit
shown. The meter displays:
SETPTS
/T1/T2
/DEV
MENU
RESET
SETPTS
/T1/T2
/DEV
MENU
RESET
6
Begin Operation
Exit the Configuration Menu and reinitialize the meter:
¥
Press RESET twice, or
¥
Press MENU until RST
flashes on the display.
/T1/T2
SETPTS
/DEV
MENU
RESET
When the temperature appears, the
meter is up and running.
To View the Temperature
Differentials:
While in run mode, press
/T1/T2/
to display:
¥
T1: Temperature 1
¥
T2: Temperature 2
¥
T1-T2: Differential between T1 and T2.
WARNING: These products are not designed for use in, and should not be used
for, patient connected applications.
This device is marked with the international caution symbol. It is important
to read the Setup Guide before installing or commissioning this device as
it contains important information relating to safety and EMC.
It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI
regulations that apply. OMEGA is constantly pursuing certification of its products to
the European New Approach Directives.
The information contained in this document is believed to be correct but OMEGA
Engineering, Inc. accepts no liability for any errors it contains, and reserves the right
to alter specifications without notice.
TRADEMARK NOTICE:
omega.com
, and
are
trademarks of OMEGA Engineering, Inc.
QUICK START
For complete product manual:
www.omega.com/manualpdf/M1865.pdf
DP26-RTD
DIFFERENTIAL TEMPERATURE
METER WITH RTD
omega.com info@omega.com
Servicing North America:
Omega Engineering, Inc.
U.S.A.
Headquaters
Toll-Free: 1-800-826-6342 (USA & Canada only)
Customer Service: 1-800-622-2378
(USA & Canada only)
Engineering Service: 1-800-872-9436
(USA & Canada only)
Tel: (203) 359-1660
Fax: (203) 359-7700
e-mail: info@omega.com
For Other Locations Visit omega.com/worldwide
TM
Advertisement
