Advertisement
1
2
NOTICE
The projector signal port and remote control
How to use the projector correctly:
1 Do not face to lens by eyes, it will hurt your eyes from
hard Light of the projector when it's working.
2 Do not block the air outlet, to avoid damage from
internal electronic device by projector can not cooling.
3 Do not use chemicals, Cleaner or water to clean, and also
avoid rain, moisture and leucocratic liquid to corrode
circuit board.
4 Please put the projector and accessories on the place
that children can not reach.
5 Please make sure the projector working environment is
dry and windy.
6 Do not place projector in too warm or too cold room, the high
temperature or low temperature will Shorten lifespan of the
device. The working environment would be 5℃~35℃ better.
7 Do not put the projector in heating equipment(drying machine,
microwave oven)to make it dry.
8 Do not press hard or put something heavy on the projector, it
will damage projector.
9 Do not throw, beat, shake projector, it will damage circuit board
Power
in it.
10 Do not dismounting projector. Please contact after-sales service
Keystone up
if you have any problem.
11 Do not fix by yourself. If projector can not working normaly,
Arrow button
please consult with after-sales service or depot repair.
SET
VOL-
3
Focus adjustment
Wi-Fi Alliance
1：Plug the power cord into a power outlet.
2：Press the button"
Ⅱ Focus adjustment
1
2
Remote the focus slider button up and down slightly,
until the picture clear.
HDMI
HDMI Signal input
1/2
Multimedia interface
Network interface
PC-RGB
VGA input
AV
Composite Video Broadcast Signal
Earphone/3.5mm AUDIO OUT
focus
Menu
Mute
3
Keystone Down
Ⅲ Screen Size Adjustment
Screen Size
60"
72"
BACK
84"
VOL+
100"
Projection distance is proportional to projector area,
HOME
The farther the distance is, the larger the projection
image are,you can adjust the distance as needed.
(This data is for reference only)
4
Connect to the network
connect to WIFI
"on the projector or on the remote control.
settings→ Wireless and networks →WiFi → WLAN，
choose the WIFI and enter the password,wait conne-
ction succeeded,you can access network.
Connect to the ethernet
Projection distance
(m)
Note:You should disconnect WIFI before connectting
1.7
to the ethernet.
2.1
1. Put cable in the RJ45 port directly,for dial up router.
2.4
2. Dial-up operation:
2.9
settings → Wireless and networks → Ethernet → PPPoE
settings,enter Username:Username;enter Password:cord
select Connect,wait,then you can access network.
5
6
Connect to the external
3D fuction
1:Use the proper cables for each connection.
The projector supports a 3D fuction,press the
The projector can connect various external
"setting"on the remote during playing the 3D video,
equipment,you should choose proper cables to
press the arrow button to select"3D mode"menu
connect to the external equipment as needed.
2:Select corresponding signal source.
(as follows),you can do more settings in this mode.
You can select the following icons from the left
side of the homepage.
AV
HDMI
PC-RGB（computer VGA port）
Add:Different brand laptop output keys are as follows:
Lenovo
Fn+F3
Fujitsu
Fn+F10
Dell
Fn+F8
Haier
Fn+F3
HP
Fn+F4
NEC
Fn+F3
Remarks:
ThinkPad
Fn+F7
Panasonic Fn+F3
Asus
Fn+F8
Sharp
Fn+F5
You must to wear a pair of matched ActiveShutter
3D glasses,to achieve 3D effect.
Acer
Fn+F5
Hitachi
Fn+F7
Samsung
Fn+F4
TOSHIBA
Fn+F5
Sony
Fn+F7
The user of windows 7 or over win- dows7.Simply press
the
+P,select "copy"to connect.If the operation above
is invalid,Please update computer graphics driver.
Advertisement
