Panasonic WV-SFV631L Installation Manual

Installation Guide
Included Installation Instructions
Network Camera
WV-SFV631L/WV-SFV631LT
Model No.
WV-SFV611L
(This illustration represents WV-SFV631L.)
● This manual describes the installation procedures, network camera installation, cable connec-
tions, and the angle of view adjustment.
● Before reading this manual, be sure to read the Important Information.
● This manual describes how to install the network camera using the WV-SFV631L model as an
example.
For U.S. and Canada: For Europe and other countries:
Panasonic Corporation
Panasonic System Communications
Company of North America,
http://panasonic.net
Unit of Panasonic Corporation
of North America
Panasonic System Networks Co., Ltd.
www.panasonic.com/business/
Fukuoka, Japan
For customer support, call 1.800.528.6747
Two Riverfront Plaza, Newark, NJ 07102-5490
Authorised Representative in EU:
Panasonic Canada Inc.
Panasonic Testing Centre
5770 Ambler Drive, Mississauga,
Panasonic Marketing Europe GmbH
Ontario, L4W 2T3 Canada
Winsbergring 15, 22525 Hamburg, Germany
(905)624-5010
www.panasonic.ca
PGQX1455XA avs1213-2064 Printed in China
© Panasonic System Networks Co., Ltd. 2014
Major operating controls
The component names of the camera are as follows. Refer to the illustration when installing or
adjusting the camera.
Direction marker for installation ( TOP)
Data Matrix: To our
● Points up when installing to a wall.
website*
MONITOR OUT terminal
(factory shipment: NTSC
monitor)
Screen display
top (TOP)
Dehumidifying
device
Direction marker
for installation
(FRONT )
• FRONT must posi-
tioned in front of the
camera (on the
Panasonic logo side).
Auto focus (AF) button
TELE button
(moves the camera to the "Tele" side)
WIDE button
(moves the camera to the "Wide" side)
SD slot 1 (SD1)
SD slot 2 (SD2)
SD ON/OFF button
*1 SDXC/SDHC/SD memory card is described as SD memory card.
*2 Depending on the scanning application used, the Data Matrix may not be able to be
read correctly. In this case, access the site by directly entering the following URL.
http://security.panasonic.com/pss/security/support/qr_sp_select.html
Standard accessories
Important Information ............................... 1 pc. CD-ROM
Installation Guide (this document) ............ 1 set Code label
Warranty card ........................................... 1 set
*1 The CD-ROM contains the operating instructions and different kinds of tool software pro-
grams.
*2 This label may be required for network management. The network administrator shall retain
the code label.
The following parts are used during installation procedures.
A Base bracket........................................ 1 pc. B Attachment plate .................................. 1 pc.
C Fixing screws for attachment plate D 4P alarm cable ..................................... 1 pc.
E
(M4 x 8 mm) ...................................... 5 pcs. MONITOR OUT conversion plug ......... 1 pc.
F
(of them, 1 for spare) Template A (for the attachment plate) 1 sheet.
G H
Template B (for the base bracket) .. 1 sheet. Bit ........................................................ 1 pc.
I J
2P power cable .................................... 1 pc. LAN cable cover .................................. 1 pc.
K
Waterproof tape ................................... 1 pc.
K
H
(Screw size 6.35 mm
{1/4 inches} torx wrench)
B Attachment
Camera
Enclosure
Dome cover
Light-blocking rubber ring
Panning table
IR LED
Azimuth adjustment ring Tilting table
Camera fixing screw
NTSC/PAL switch
● The MONITOR OUT terminal output can be switched for NTSC or PAL monitors.
IMPORTANT:
● This is valid if the [Monitor out] is set to [Switch priority] ([Switch priority] is selected by
default). For details, refer to the Operating Instructions (included in the CD-ROM).
2
INITIAL SET button
● How to initialize the camera
Follow the steps below to initialize the network camera.
1 Turn off the power of the camera. When using a PoE hub, disconnect the LAN cable from the cam-
era. When using an external power supply, disconnect the 2P power cable plug from the camera.
2 Turn on the power of the camera while holding down the INITIAL SET button, and then keep
holding down the button for 5 seconds or more. About 2 minutes later, The camera will start
up and the settings including the network settings will be initialized.
IMPORTANT:
● When the camera is initialized, the settings including the network settings will be initial-
ized. Note that the CRT key (SSL encryption key) used for the HTTPS protocol will not
be initialized.
● Before initializing the settings, it is recommended to write down the settings in advance.
● Do not turn off the power of the camera during the process of initialization. Otherwise, it
may fail to initialize and may cause malfunction.
ACT indicator
● When data is being sent via the network camera
LINK indicator
● When the camera is able to communicate with the connected device
SD MOUNT indicator
1
● When an SD memory card* is inserted and could
be recognized
● When data can be saved after the SD memory card is
inserted and the SD ON/OFF button is pressed
● When data can be saved to the SD memory card
● When the SD memory card is removed after holding down
the SD ON/OFF button for about 2 seconds
● When data cannot be saved to the SD memory card because
an abnormality was detected or the SD memory card is
configured not to be used
SD ERROR/AF indicator
● When AF (Auto Focus) operation is being executed
● When the set is being started
● When an SD memory card is recognized normally
● When an abnormality is detected in both SD1 and SD2
cards after the camera has started
● When an abnormality is only detected in the SD1 card
after the camera has started
● When an abnormality is only detected in the SD2 card
after the camera has started
Making connections
Turn off each system's power supply before making a connection. Before making connections,
................................................. 1 pc.
*1
prepare the required peripheral devices and cables.
.............................................. 1 pc.
*2
Connect a LAN cable (category 5 or better, straight)
IMPORTANT:
● Use all 4 pairs (8 pins) of the LAN cable (category 5 or better, straight).
● The maximum cable length is 100 m {328 feet}.
● Make sure that the PoE device in use is compliant with IEEE802.3af standard.
● When connecting both the 12 V DC power supply and the PoE device for power sup-
ply, 12 V DC will be used for power supply*.
* If a 12 V DC power supply and a PoE hub or router are used at the same time, net-
work connections may not be possible. In this case, disable the PoE settings.
Refer to the operating instructions of the PoE hub or router in use.
* In the situation where a 12 V DC power supply and a PoE hub or router are used at the
same time and the 12 V DC power supply is then disconnected, the power supply may
be stopped and the camera may restart depending on the PoE hub or router used.
● When the LAN cable is disconnected once, reconnect the cable after around 2 seconds.
When the cable is quickly reconnected, the power may not be supplied from the PoE device.
● When cables are used outdoors, there is a chance that they may be affected by lightning.
In this case, install a lightning arrester just before where the cables connect to the camera.
RJ45 (female)
Network cable
A Base bracket
plate (accessory)
(accessory)
Alarm input/output cable
Microphone/line input cable
Connect a monaural mini plug (ø3.5 mm).
C Fixing screws for
● Input impedance: Approx. 2 kΩ (unbalanced)
attachment plate
● Recommended cable length: Less than 1 m {3.28 feet} (for microphone input)
(accessory)
● Recommended microphone: Plug-in power type (option)
● Supply voltage: 2.5 V ±0.5 V
● Recommended sensitivity of microphone: –48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)
● Input level for the line input: Approx. –10 dBV
Waterproof treatment for the cable joint sections
Adequate waterproof treatment is required for the cables when installing the camera with cables
exposed or installing it under the eaves. The camera body is waterproof, but the cable ends are
not waterproof.
Be sure to use the supplied waterproof tape at the points where the cables are connected to ap-
ply waterproof treatment in the following procedure. Failure to observe this or use of a tape other
than the provided waterproof tape (such as a vinyl tape) may cause water leakage resulting in
malfunction.
<LAN cable>
Wind the tape in a
half-overlapping manner.
Blinks green (accessing)
IMPORTANT:
How to wind the supplied waterproof tape
Lights orange
● Also waterproof the 2P power cable (accessory), 4P
alarm cable (accessory), and external connections in
Lights off → Blinks green → the same way.
Lights off
● Stretch the tape by approx. twice (see the illustration)
Lights off → Lights green
and wind it around the cable. Insufficient tape stretch
causes insufficient waterproofing.
Lights green
● To prevent the LAN cable hook from coming loose
Lights green → Blinks green → Lights off
easily, fit the J LAN cable cover onto the pigtail
cable as illustrated, and then slide it in the direction
Lights off
indicated by the arrow.
The connector of the LAN cable used with this cam-
era must meet the following restrictions.
Height when inserted (From bottom to hook.):
Blinks red (Interval of 1 time/ second)
Max. 16 mm {5/8 inches}
Lights red
Connector width: Max. 14 mm {9/16 inches}
Lights red → Lights off
● To install this product outdoors, be sure to waterproof
Lights red
the cables. Waterproof grade (IEC IP66 or equiva-
Lights red → Blinks red lent) is applied to this product only when it is installed
(Interval of 1 time/ 3 seconds)
correctly as described in these operating instructions
Lights red → Blinks red
and appropriate waterproof treatment is applied. The
(Interval of 2 times/ 3 seconds)
internal parts of base brackets are not waterproofed.
Connect the alarm input/output cable
D 4P alarm cable (accessory)
<Ratings>
• ALARM IN1(DAY/NIGHT IN), ALARM IN2, ALARM IN3
Input specifi cation: No-voltage make contact input (4 V - 5 V DC, internally pulled up)
OFF:
ON:
• ALARM OUT, AUX OUT
Output specifi cation: Open collector output (maximum applied voltage: 20 V DC)
Open:
Close:
* The default of EXT I/O terminals is "Off".
IMPORTANT:
● Be sure to use the 4P alarm cable provided with this product.
● Off, input, and output of the external I/O terminal 2 and 3 can be switched by configur-
ing the setting. Refer to the Operating Instructions on the provided CD-ROM for fur-
ther information about the EXT I/O terminal 2 and 3 (ALARM IN2, 3) settings ("Off",
"Alarm input", "Alarm output" or "AUX output").
● When using the EXT I/O terminals as the output terminals, ensure they do not cause
signal collision with external signals.
● Install external devices so that they do not exceed the ratings above.
LAN cable (category 5 or better
Connect the power cable
straight)
Caution:
● A READILY ACCESSIBLE DISCONNECT DEVICE SHALL
4P alarm cable
Ⓓ
BE INCORPORATED TO THE EQUIPMENT POWERED
(accessory)
BY 12 V DC POWER SUPPLY.
● ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL
12 V DC (red)
1310/CSA 223) or LIMITED POWER SOURCE (IEC/EN/
GND (black) UL/CSA 60950-1).
Power cable
I 2P power cable (accessory)
Connect the output cable of the AC adaptor to the 2P power cable.
(12 V DC)
IMPORTANT:
● The 12 V DC power supply shall be insulated from the commercial AC power.
Microphone/line input cable (white)
● Be sure to use the 2P power cable provided with this product.
● Be sure to fully insert the 2P power cable into the 12 V DC power supply terminal.
Audio output cable (black)
Otherwise, it may damage the camera or cause malfunction.
● When installing the camera, make sure that excessive force is not applied to the
power cable.
Connect an external amplifier-embedded speaker to the audio output cable
Connect a stereo mini plug (ø3.5 mm) (Audio output is monaural.).*
● Output impedance: Approx. 600 Ω (unbalanced)
● Recommended cable length: Less than 10 m {32.8 feet}
● Output level: –20 dBV
Less than 10 m {32.8 feet} (for line input)
IMPORTANT:
● Connect/disconnect the audio cables and turn on the power of the camera after turn-
ing off the power of the audio output devices. Otherwise, loud noise may be heard
from the speaker.
● Make sure that the stereo mini plug is connected to this cable. When a monaural mini
plug is connected, audio may not be heard.
When connecting a monaural speaker with amplifier, use a locally procured conver-
sion cable (mono-stereo).
When connecting to a network using a PoE hub
Before starting the installation, check the entire system confi guration. The following illustration
gives a wiring example of how to connect the camera to the network via a PoE device (hub).
Powered speaker
< Alarm input/output cable, power cable, micro-
phone/line input cable, audio output cable>
Microphone
Wind the tape in a
half-overlapping
manner.
Powered speaker
Stretch the tape to
about twice.
Microphone
2x
<Required cable>
LAN cable*
Use a LAN cable*
J LAN cable cover
*1 Recommended cable length from the speaker: less than 10 m {32.8 feet}
Recommended cable length from the microphone: less than 1 m {3.28 feet}
*2 Shielded (STP) LAN cables must be used with this unit to ensure compliance with CE stan-
dards.
IMPORTANT:
● The adjustment monitor is used for checking the adjustment of the angular field of view when
installing the camera or when servicing. It is not provided for recording/monitoring use.
● Depending on the monitor, some characters (camera title, preset ID, etc.) may not be
displayed on the screen.
The hook engages
with the connector ● Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.
terminal
● If a PoE hub is not used, each network camera must be connected to a 12 V DC power
supply.
● When using 12 V DC, power supply from a PoE hub or router is not required.
GND (black)
ALARM IN3, AUX OUT (gray) (Terminal 3)
ALARM IN2, ALARM OUT (red) (Terminal 2)
ALARM IN1, DAY/NIGHT IN (green) (Terminal 1)
Open or 4 V - 5 V DC
Make contact with GND (required drive current: 1 mA or more)
4 V - 5 V DC by internal pull-up
Output voltage 1 V DC or less (maximum drive current: 50 mA)
Power cable
12 V DC
Red Positive
Black Negative
*
Use an external powered
speaker.
Adjustment monitor
PoE device (hub)
LAN cable
(category 5 or better,
straight)
PC
LAN cable
(category 5 or
better, straight)
LAN cable
(category 5 or better,
straight)
Adjustment monitor
Recommended total
extended cable length* 1
2
(category 5 or better, straight)
2
(category 5 or better, cross) when directly connecting the camera to a PC.