RCA VR628HF User Manual page 3

IMPORTANT SAFEGUARDS
In addition to the careful attention devoted to quality standards in the manufacture of your product, safety is a major
factor in the design of every product. However, safety is your responsibility too.
This sheet lists important information that will help to assure your enjoyment and proper use of.the productand
accessory equipment. Please read them carefully before operating and using your product.
Installation
Read and Follow InstructionswAII
the safety and operating instructions
should be read before the product is
operated. Follow all operating
instructions.
2 Retain Instructions_The safety and
operating instructions should be retained for future
reference.
4
Heed Warnings--Comply with all warnings on the
product and in the operating instructions.
Polarization/GroundingwThis product is equipped
with either a polarized, non-polarized, or a grounding
type power cord plug. If equipped with the non-
polarized type (two blades of identical size), the
following does not apply.
• A polarized power plug (two blades,
one wider than the other) will fit into a
power receptacle only one way. This is a
safety feature. Do not defeat it. If you
are unable to insert the plug fully, try
reversing it, or have an electrician
change the receptacle. If you need an
extension cord, use only a polarized extension cord.
• A grounding type power plug (two
blades and a round pin) will fit only into
a grounding type receptacle with
matching openings. This is safety feature.
Do not defeat it. You may need an
electrician to install a grounding type
receptacle. If you need an extension cord, use only a
grounding type extension cord.
Power Source,s--This product should be operated
only from the type of power source indicated on the
product's marking label. If you are not sure of the type
of power supply to your home, consult yc_ur dealer or
local power company. For products intended to :
operate from battery power, or other sources, refer to
the operating instructions.
6 Overloading--I_o not overload
wall outlets or extension cords as
this can result in a risk of fire or
electric shock. Overloaded AC
outlets, extension cords, frayed
power cords, damaged or cracked
wire insulation, and broken plugs
are dangerous. They may result in a shock or fire
hazard. Periodically examine the cord, and if its
appearance indicates_damage or deteriorated
insulation, have it replacedby your service technician.
Tocom 15154100
10
11
Power-Cord Protection--_Power-supply cords should
be routed so that they are not likely to be walked on
or pinched by items placed upon or against them. Pay
particular attention to cords where they are attached
to plugs, convenience receptacles and at the point
where they exit from t_he product.
VentilationmSIots and openings in the enclosure are
provided for ventilation to ensure reliable operation of
the product and to protect it from overheating. These
openings must not be blocked or covered. :These
openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface
This product should never be placed near or over a
radiator or heat register, or another heat source
(including amplifiers). This product should not be
placed in a built-in installation such as a bookcase or
equipment rack unless proper ventilation is provided or
the product manufacturer's instructions have been
followed.
AttachmentsmDo not use attachments unless
recommended by the product manufacturer as they
may cause hazards.
Water and Moisture--Do not use this product near
water--for example, near a bath tub, wash bowl,
kitchen sink or laundry tub, in a wet basement, or near
a swimming pool and thee like.
AccessoriesmDo not place this product on an
unstable surface or support. The product may fall,
causing serious injury to a child or adult as well as
serious damage to the product. Any mounting of the
product should follow the manufacturer's instructions
and use only a mountinq accessory recommended by
the manufacturer.
11A A product and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the product and
cart combination to overturn.