Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Acclaim Lighting AL Graze DC
Summary of Contents for Acclaim Lighting AL Graze DC
- Page 1 AL Graze DC (CV and DMX) User guide...
-
Page 3: Table Of Contents
Contents Introduction ..............2 Welcome Safety Supplied items Optional extras Installation ................5 Mount adjustment Removing and replacing brackets Fitting a glare shield Fitting a louver Fitting extender bars Power and control wiring Extending fixture runs beyond 12 feet DMX channel designations Operation ............... -
Page 4: Introduction
Available in 1’ and 4’ lengths these robust units can be connected in series to greatly simplify installation. In both 1’ and 4’ lengths, the AL Graze DC range is divided into two control methods: • AL Graze DC CV - controlled entirely by the power input. For non-dim applications simply attach a regulated 24VDC supply. -
Page 5: Supplied Items
1’ (30cm) [AGELC1] [AGDLC1] 5’ (1.5m) [AGELC5] [AGDLC5] 10’ (3m) [AGELC10] [AGDLC10] End caps [AGEEC] [AGDEC] T-cable (for AL Graze DC DMX models) [AGDT1] DMX/RDM tool plus male 5pin XLR lead (for AL Graze DC DMX models) [XMT350] continued overleaf www.acclaimlighting.com... - Page 6 120VAC input, 300W (powers 2 x 12’ runs) [M300L24DC] 277VAC input, 150W (powers 1 x 12’ run) [M150L24DC-277] 277VAC input, 300W (powers 2 x 12’ runs) [M300L24DC-277] 800W dimming driver (for AL Graze DC CV models) DMX, RDM, 0-10V or DALI input [ALD-800-24] www.acclaimlighting.com...
-
Page 7: Installation
Note: It may be necessary to temporarily remove the mounts from the AL Graze DC unit in order to fix them to the surface. See page 6 for details. -
Page 8: Removing And Replacing Brackets
Removing and replacing brackets Two types of mount brackets are supplied with each AL Graze DC fixture and these are easily changed. Use a 1/16th (1.5mm) Allen wrench to loosen the two grub screws on each bracket. Then slide the bracket to the center of the fixture where the rails widen to allow the feet of the bracket to be released. -
Page 9: Fitting A Glare Shield
To fit a louver 1 Lower the louver over the front face of the AL Graze DC until the four tabs of the louver click into place around the upper body of the fixture. -
Page 10: Fitting Extender Bars
Fitting extender bars A common fixing method is to use optional extender bars. These are available in 12” and 24” lengths. Two extender bars are required for each AL Graze DC fixture. Ø 0.24” (6mm) mounting holes (screws not supplied) -
Page 11: Power And Control Wiring
• AL Graze DC CV units require a regulated 24VDC power input only and so use 2-pin connectors. Dimming can be achieved using either a 24VDC constant voltage (CV) -
Page 12: Extending Fixture Runs Beyond 12 Feet
T-cable: continues the DMX control connection while terminating and replacing the power connection Where the T-cable body needs to be secured, Acclaim Lighting recommends the use of a standard 3/4” pipe strap: 3/4” pipe strap (not supplied) www.acclaimlighting.com... - Page 13 +24VDC These transformers can be connected alongside (or in place of ) an incumbent lighting fixture and convert the dimmed mains to the 24VDC supply required by AL Graze DC CV fixtures. Available in the following variants. • 120VAC input, 150W capacity (can power 1 x 12’ run) [M150L24DC] •...
- Page 14 (and the total length of fixtures plus cable lengths) is not exceeded. * AL Graze DC feed-in and link cables use 18AWG wires for their power connections. It is possible to increase the total fixture + cable lengths by using custom cables with larger power cores:...
-
Page 15: Dmx Channel Designations
Each XMT-350 DMX/RDM tool is supplied with a 5-pin male XLR lead that can be used to make a temporary control input link with the AL Graze DC DMX feed-in cable. Use a 3-pin terminal block, wire nuts, conn blocks or Wago® connectors to temporarily join the two... -
Page 16: Operation
Operation Addressing fixtures (AL Graze DC DMX models only) AL Graze DC DMX fixtures have no external controls and instead rely on RDM (Remote Device Management) for all configuration via the DMX interface. This allows multiple devices to be configured either before or after installation. -
Page 17: Testing Emitter Output
Testing emitter output (AL Graze DC DMX models only) After you have addressed each AL Graze DC DMX fixture we recommend that you also test each one prior to installation. This can be achieved with your RDM (Remote Device Management) tool. Various third party DMX/RDM tools are available; Acclaim Lighting recommends the Swisson XMT-350 for this task. -
Page 18: Further Information
Further information Troubleshooting Luminaire doesn’t turn on • Check that power is correctly applied to the fixture and that there is no damage to the power input cord. • (DMX models) Use an RDM tool (such as the Swisson XMT-350) to check the settings and internal temperature of the fixture. -
Page 19: Specifications
Specifications Color models 2700K, 3000K, 3500K and 4000K white All above + RGB, RGBW, RGBA or Dynamic White (2200-5000K) DMX: Beam angle options x 15 , 10 x 60 , 30 x 60 or 60 x 60 Illuminance (lm/ft 419 (4000K 30 x 60 variant @ 100% - 1 foot section) Lumen maintenance (L... -
Page 20: Limited Product Warranty
If the requested repairs or service (including parts replacement) are within the terms of this warranty, Acclaim Lighting™ will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in its original package. - Page 22 www.acclaimlighting.com...
Need help?
Do you have a question about the AL Graze DC and is the answer not in the manual?
Questions and answers